Schneider Electric C2535E250 Trip unit MicroLogic Instructions

Schneider Electric C2535E250 Trip unit MicroLogic

Product Information

Specifications

• Model: ComPacTTM NSX100-250
• MicroLogic Versions: 2.2, 5.2, 6.2, MicroLogic 5/6/7
• Support: www.se.com/support
• Document Numbers: NNZ4765407, DOCA0187EN, DOCA0187FR, DOCA0187ES, DOCA0187ZH, DOCA0188EN, DOCA0188FR, DOCA0188ES, DOCA0188ZH

FAQ

Q: Can I install the product myself?

A: No, electrical equipment should be installed by qualified personnel to ensure safety and proper functioning.

Q: How do I confirm the power is off before working on the equipment?

A: Always use a properly rated voltage sensing device to verify that the power is off before conducting any maintenance tasks.

Q: What should I do if I encounter a hazard while using the product?

A: Stop using the equipment immediately, follow safety procedures, and contact qualified personnel for assistance.

MicroLogic 2.2/5.2/6.2 Trip Units

www.se.com/support

Retain instruction sheet for future use. Visit our website at www.se.com to download the documents listed above (user guides or instruction sheets ) and other documents

PLEASE NOTE

• Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel.
• No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material.
• All pertinent state, regional, and local safety regulations must be observed when installing and using this product.

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH

• Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E, CSA Z462, NOM-029-STPS or local equivalent.
• This equipment must only be installed and serviced by qualified electrical personnel. p Turn off all power supplying this equipment before working on or inside equipment.
• Always use a properly rated voltage sensing device to confirm power is off.
• Put back all devices, doors, and covers before turning on power to this equipment. p Beware of potential hazards, and carefully inspect the work area for tools and objects that may have been left inside the equipment.
• Failure to follow these instructions will result in death or serious injury.

WARNING: This product can expose you to chemicals including lead and lead compounds, which are known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov.

Required for Installation

Before Working on Equipment

1. Turn off all power supplying this equipment before working on or inside equipment.
2. Use push-to-trip button to trip the device.
3. Use a properly rated voltage sensing device to confirm power is off.

Installation

WARNING

HAZARD OF FIRE

• When installing the MicroLogic trip unit, check that the snap-off screws break A when tightened.
• It is mandatory to use snap-off screws LV429513 to install a MicroLogic trip unit. p In case of replacement of the trip unit by a trip unit with a different rating, you must: p re-define the trip unit settings
• adapt the connection characteristics. Failure to follow these instructions can result in death, serious injury, or equipment damage.

MicroLogic 2.2

MicroLogic 5.2/6.2

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
Install MicroLogic 5/6 trip units with the internal rubber insulation screen in the right position.
Failure to follow these instructions will result in death or serious injury.

3P/4P

Reinstall Front Cover

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
Put back front cover or accessories before energizing device to prevent access to live terminals.
Failure to follow these instructions will result in death or serious injury.

NOTICE

HAZARD OF EQUIPMENT DAMAGE

• Be careful not to pinch wires when installing front cover.
• Tighten all front cover screws to stated torque.
• Do not overtorque screws.
• Do not use power equipment to torque screws.
• Failure to follow these instructions can result in equipment damage.

1. Put back front cover and accessories as indicated in instruction sheet shipped with device.
2. Device is ready to be placed in service.

Tripping Test

MicroLogic 2.2: Trip Unit Adjustment

MicroLogic 5.2/6.2: Trip Unit Adjustment

Trip Unit Supply

Settings with Rotary Dia

Sealing

To install the sealing accessory,consult the instruction sheet GHD16296AA.

MicroLogic 2.2

3P/4P

MicroLogic 5.2/6.2

Manufacturing Date

The product’s manufacture date is coded PP-YYYY-Www-D, where:

• PP: plant code
• YYYY: year of manufacture
• Www: week of manufacture
• D: weekday of manufacture (Monday = 1)
  Eg: 7Q-2019-W20-3 = product manufactured at plant 7Q on Wednesday 15 May 2019

Schneider Electric Industries SAS 35, rue Joseph Monier
CS 30323
F – 92506 Rueil Malmaison Cedex www.se.com
NNZ4765207-02

Schneider Electric Limited Stafford Park 5
Telford, TF3 3BL
United Kingdom
www.se.com/uk

© 2023 Schneider Electric – All rights reserved.

References

• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>