Fuyu A01 Bedside Table Instruction Manual

Fuyu A01 Bedside Table

Product Information

Specifications

• Product: Bedside Table with Biometric Lock
• Components: 4 feet, screws, power adapter
• Minimum Installation Distance: 15 cm between radiator and user body

Product Usage Instructions

Unpacking and Inspection:
Handle valuables with care. Check the appearance of the product after unpacking to ensure it is in good condition.

Assembly

1. Open the drawer and remove the accessories: 4 feet, screws, and power adapter.
2. Install the feet:
   • Place a soft cushion on the ground.
   • Turn the cabinet upside down and position the four feet on the corners of the cabinet.
   • Align the corners of the feet with the corners of the cabinet and secure them with small screws.

Biometric Lock Setup:

1. To add fingerprints:
   • Long press until the green light is on 3 times to enter setting status.
   • When the blue light is on, add fingerprints by pressing the sensor 5-12 times.
2. To delete fingerprints and restore factory settings:
   • Method 1: Long press with the registered fingerprint until red light is on, then release.
   • Method 2: Insert E-key, any fingerprint can unlock. Green light indicates success.between the radiator and user

Frequently Asked Questions (FAQ)
Q: What should I do if I encounter issues with adding fingerprints?
A: If facing difficulties in adding fingerprints, follow the steps mentioned in the manual carefully and ensure proper placement on the sensor.

Bedside table instruction manual

1. Please handle the valuables with care, and first check whether the appearance is in good condition after unpacking.

2. Open the drawer and take out the accessories inside: 4 feet, screws, power adapter。

3. Install the feet: Put a soft cushion on the ground, put the cabinet upside down, put the four feet on the four corners of the cabinet, the corners of the feet are aligned with the corners of the cabinet, and screw it directly with small screws to fix it.
   The corners of the feet are aligned with the corners of the cabinet when viewed from the front

4.  Connect one end of the power supply to the socket (the small light of the power supply lights up at this time) and the other end to the power interface of the cabinet (the touch switch on the cabinet panel lights up to indicate that the power supply is normally powered on). Click the touch switch light strip to adjust the three colors, long press the touch switch to adjust the brightness of the light strip, and long press the touch switch to turn off the light of the switch when the light strip is off.

5.  Place the mobile phone with wireless charging function on the center point of the panel to charge the mobile phone. At present, it supports most mobile phones with wireless charging function on the market (some mobile phones are not compatible). Note: Be sure to focus on the center point, wait for a few seconds after placing it, and wait for the device to respond. If there is a mobile phone case that will affect the charging, you can remove it first.

6. For the style with fingerprint lock configuration, please refer to the fingerprint lock setting steps on the back.

7. long press until green light on 3 times（enter setting status） remove finger

8. Blue light on（add fingerprints）press sensor for 5~12 times

9. Success：green light on;Fail：red light on ,follow the steps and try again

10. Blue light on, repeat the above steps to register more fingerprints or waiting for exit （allow register 10-20）

Add fingerprints：

Put the same finger on,until green light on 3 times（enter setting system）then remove and register new fingerprints.

E-key function（restore factory）
If you haven’t entered your fingerprint.You can insert E-KEY to usb port,put any fingerprint to unlock.
Delete fingerprints and restore factory(Two choices)

1. Method 1.Long press with the registered fingerprint until red light on then
   release,green light on mean success

2. Method 2.Inseting E-key,any fingerprint unlock ,green light on mean success
   Low battery tips：When it unlock ， red light on，reminder low battery ， user should change new battery for the lock.If haven’t change battery ,the lock will stop work.
   If can’t unlock mean running out of battery,can use micro USB inset to pannel USB socket and unlock ,please change the battery after unlock.

• Green light on 1 times：unlock/locking
• Green light on 3 times：enter setting status
• Blue light on：add fingerprints
• Red light on：reminder

FCC Warning Statement

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment must be installed and operated with a minimum distance of 15 cm between the radiator and user body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>