Schneider Electric Harmony XB5 Pilot Light Instructions
- July 8, 2024
- Schneider Electric
Table of Contents
Schneider Electric Harmony XB5 Pilot Light
Specifications
-
Manufacturer: Schneider Electric Industries SAS
-
Brand Name: Schneider Electric
-
Product Function: The function of the complete
the pilot light unit is to provide a signal when receiving rated voltage input -
Product Reference: XB5AVB3
-
Total Representative Product Mass: 28g
-
Representative Product Dimensions: H41.5mm x L54mm x D30mm
-
Date of Information Release: 10/2023
Product Usage Instructions
Installation
Follow these steps to install the Harmony XB5 Pilot Light:
- Ensure the power is off before starting installation.
- Mount the pilot light securely using appropriate screws or brackets.
- Connect the electronic board for communication if required.
Operation
To operate the pilot light
- Apply the rated voltage input to trigger the signal indication.
- Observe the LED block for visual feedback.
Maintenance
Regularly check for any signs of damage or wear and tear. Clean the
diffuser and bezel as needed to maintain visibility.
Schneider Electric Harmony XB5 Pilot Light
The information provided in this document assumes that the product is completely de-energized and uninstalled (refer to the instructions provided in the appropriate product manuals). Dismantling/disassembling the product may entail hazards caused by, for example, shared edges, chemical aggression, or selected parts.
WARNING
HAZARD DUE TO INSUFFICIENT PROTECTION • Implement all safety measures required by the applicable regulations and by the processes used to dismantle/disassemble and dispose of the product. • Use all necessary personal protective equipment such as gloves and goggles. Failure to follow these instructions can result in death or serious injury.
End-of-Life Instructions
Recommendation| Number on
drawing
| Component / Material| Weight
(in g)
| Comment
---|---|---|---|---
To be depolluted| 1| Bezel, Base, LED Block Housing| 15.20| Plastics With FR
To be dismantled| 2| Cap, Diffuser, Gasket| 5.69| Plastics Without FR
To be dismantled| 3| Washer, Screw, Bracket| 6.36| Metal Parts
To be depolluted| 4| Electronic Board (Communication) > 10cm| 0.5106| PCBA
Other| | Liquid and pasty substances| 0.1| Glue
---|---|---|---|---
Product Description
| Manufacturer identification | Schneider Electric Industries SAS |
|---|---|
| Brand name | Schneider Electric |
| Product function | The function of a complete pilot light unit is to |
provide a signal when receiving rated voltage input.
Product reference| XB5AVB3
Total representative product mass| 28 g
Representative product dimensions| H41.5mm x L54 mm x D30 mm
Accessories| No accessories needed
Date of information release| 10/2023
Additional information
Legal information
| This product family is in the scope of European Union directive 2012/19/EU
on Waste Electrical and Electronic Equipment (WEEE). The product family must
be disposed of according to the legislation of the country. This document is
intended for use by end-of-life recyclers or treatment facilities. It provides
the basic information to ensure an appropriate end-of-life treatment for the
components and materials of the product.
---|---
In case of special transportation:
transportation method
| No specific means of transportation are required.
Recyclability potential
|
22%
| The recyclability rate has been calculated based on the REEECY’LAB tool developed by
Ecosystem, for components/materials not covered by the tool, data from the “ECO’DEEE recyclability and recoverability calculation method” was taken. If no data was found a conservative assumption was used (0% recyclability).
Schneider Electric Industries SAS Country Customer Care Center http://www .schneider-electric.com/contact
CS 30323 F- 92500 Rueil Malmaison Cedex RCS Nanterre 954 503 439 Capital social 928 298 512 €
www.se.com ENVEOLI2308027_V1
Published by Schneider Electric © 2023 – Schneider Electric – All rights reserved
FAQ
Q: How should I dispose of the Harmony XB5 Pilot Light at the end of its
life?
A: To dispose of the product, follow the end-of-life instructions
provided in the manual. Ensure de-pollution and dismantling as recommended
based on the component/material list.
Q: Is there a need for special transportation for recycling this
product
A: No specific means of transportation are required for recycling the
product. Check with local regulations for proper disposal methods