BOSCH BSP3200 SmartphoneGrip Phone Holder Instruction Manual

BSP3200 SmartphoneGrip Phone Holder
Instruction Manual

|
---|---

Safety Instructions

Read all the safety information and instructions. Failure to observe the safety information and follow instructions may result in electric shock, fire, and/or serious injury.

Save all safety warnings and instructions for future reference.

• Read and observe the safety warnings and directions
  contained in all the eBike system operating instructions and in the operating instructions of your eBike.

• Do not allow your attention to be diverted from surrounding traffic when using Bosch eBike components and always ride with both hands on the handlebars. Always observe the applicable legal provisions in your country for the permitted use of your bicycle in road traffic. In particular, note that it is prohibited to pick up or hold your smartphone in your hand in road traffic.

• Set the display brightness so that you can adequately see important information such as speed and warning symbols. Incorrectly set display brightness may lead to dangerous situations.

• The contact surfaces of the display holder may become very hot (> 60 °C). Allow the contact surfaces to adjust to the ambient temperature before you touch them. This is particularly important when using a SmartphoneGrip.

• Consult a doctor before using fitness app programs.
  Fitness apps may cause people to overexert themselves physically.

• Always observe local restrictions for using electronic devices.

• Avoid operation near your body for extended periods.

• Do not stand your bicycle upside down on its saddle and handlebars if the SmartphoneGrip or its holder protrudes from the handlebars. This may irreparably damage the  SmartphoneGrip or the holder.

• Do not use the SmartphoneGrip as a handle. Lifting the eBike up by the SmartphoneGrip can cause irreparable damage to the SmartphoneGrip.

• Do not open the SmartphoneGrip. Opening the SmartphoneGrip may damage it beyond repair and void any warranty claims.

• Caution! When using the SmartphoneGrip with Bluetooth® and/or Wi-Fi, interference can occur with other devices and equipment, aircraft, and medical devices (e.g. pacemakers, hearing aids). Likewise, injury to people and animals in the immediate vicinity cannot be excluded entirely. Do not use the SmartphoneGrip with Bluetooth® in the vicinity of medical devices, petrol stations, chemical plants, areas with a potentially explosive atmosphere or on blast sites. Do not use the SmartphoneGrip with Bluetooth® in airplanes. Avoid operation near your body for extended periods.

NOTICE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device must not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

NOTICE: Changes or modifications made to this equipment not expressly approved by Robert Bosch GmbH may void the FCC authorization to operate this equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Radiofrequency radiation exposure Information: The radiated output power of the device is far below the FCC radio frequency exposure limits. Nevertheless, the device shall be used in such a manner that the potential for human contact during normal operation is minimized.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

ISED Notice (Canada)
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with Canada’s radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Product Description and Specifications

Intended Use

The Bosch SmartphoneGrip is designed to hold and charge a smartphone on the handlebars of a Bosch eBike system.
In addition to the functions shown here, changes to software relating to troubleshooting and functional modifications may be introduced at any time.
The manufacturer accepts no liability for damage to mobile devices caused by using this product. The manufacturer accepts no liability for defects related to damage or loss due
to factors outside of the manufacturer’s control, or for products that were modified or damaged due to improper or incorrect use.

Product Features

The numbering of the components shown refers to the illustrations on the graphics pages at the beginning of the manual. All illustrations of bike parts except for the drive unit, SmartphoneGrip (including operating unit), speed sensor, and the corresponding holders are schematic representations and may differ on your eBike.

1. Front retraining bracket, movable
2. Rear retaining bracket, fixed
3. USB port with USB cap
4. Release mechanism
5. SmartphoneGrip mount
6. Snap-in hook
7. Socket contacts
8. SmartphoneGrip contacts
9. Status LED
10. Inductive charging coil
11. Display mount fastening screw
12. Removal blocker
13. Keypad lock
14. Hex key
15. Smartphone
16. Adapter tray

Technical Data

SmartphoneGrip

Efficiency > 67 %
Maximum RF output power| | 40.36dBuA/m at 3m distance
Frequency range| KHz| 110-205
Operating temperature| °C| -5 to 40
Storage temperature| ° C| 10 to 40
Protection rating| | IP54
Weight, approx.| g| 75

Assembly

SmartphoneGrip Assembly (see figure A)
Press and hold the release mechanism (4) to position the SmartphoneGrip. Place the upper edge of the Smartphone grip next to the snap-in hook (6) of the display holder (5) ➊. Pull the SmartphoneGrip towards you and push the SmartphoneGrip onto the display holder ➋. Let go of the release mechanism (4). Press the release mechanism (4) while pulling it towards you ➊ to remove the SmartphoneGrip. Remove the SmartphoneGrip and let go of the release mechanism (4) ➋.

Inserting the Removal Blocker (see figure B)
Insert the removal blocker (12) into the adapter tray (16) from below until you hear the removal blocker (12) click into place.
From this point onwards, you can no longer remove the SmartphoneGrip from the display mount (5) without removing the display mount (5) from the adapter tray (16)
by loosening the two fastening screws (11).
Note: The removal blocker (12) is not an anti-theft device.

Smartphone Assembly (see figure C)
The SmartphoneGrip can hold smartphones in the following sizes:

The specified dimensions include any phone cases. Smartphones with folio cases must not be used. The total weight must not exceed 276 g.
Pull the front retaining bracket (1) forwards ➊. Insert your smartphone (15) with the long side of the phone positioned against the fixed retaining bracket (2) ➋. Release the
front retaining bracket and place your smartphone (15) in the center of the SmartphoneGrip ➌.

• Be careful not to pinch your fingers between the movable retaining bracket and the SmartphoneGrip when inserting your smartphone.
  Once you have inserted your smartphone, check that the smartphone cannot come into contact with any hard parts on the bike even in case of vibrations, as this could cause lasting damage to the smartphone.

Keypad Lock Assembly (see figure D)
To remove the keypad lock (13), unscrew the securing screw with a hex key (1.5 mm) (14) ➊ and remove the keypad lock (13) ➋.
To insert the keypad lock (13), slide the keypad lock (13) into the provided opening and screw it into place with a hex key (1.5 mm) (14).
Note: The keypad lock is not an anti-theft device. The keypad lock prevents the SmartphoneGrip from being quickly removed from the holder. The keypad lock does not affect  the smartphone in any way
Note: Never leave your smartphone unattended in the SmartphoneGrip.

Operation

Starting Operation

Place your smartphone in the SmartphoneGrip.
Start the eBike Flow app to have riding data displayed.

http://www.bosch-ebike.com/qr/flow-app-packaging

Depending on the smartphone’s operating system, the eBike Flow app can be downloaded free of charge from the Apple App Store and the Google Play store.

Use your smartphone to scan the code in order to download the eBike Flow app.

Charging your Smartphone
While the smartphone is in the SmartphoneGrip, it can be charged at the same time as displaying riding data. If your smartphone has an inductive charging function, you can charge the smartphone without needing a cable.

Inductive Charging
The charging process starts automatically when you place a smartphone with an inductive charging function in the SmartphoneGrip. The status LED (9) lights up yellow. When the smartphone is fully charged, the status LED (9) will light up green permanently.
The charging voltage is switched off when you remove the smartphone from the holder.

Charging via USB
If your smartphone does not have an inductive charging function, you can charge your smartphone via the USB  port (3). To do so, open the USB cap and connect a separate
USB cable (not included in the scope of delivery) to the Micro-AB USB port. Pay attention to the type of plug required for your smartphone when purchasing the USB cable.

Status Indicators

The status LED (9) indicates the following statuses with different colors and lighting patterns:

The following alarm states are detected and will lead to the inductive charging process being interrupted:

• Detection of foreign objects, e.g. coins, keys or other metallic objects

• Temperature alarm
  The charging process will switch off at temperatures above 78 °C. The charging process is continued once the temperature drops below 56 °C.

• Overvoltage alarm at voltages above 6 V

• Undervoltage alarm at voltages below 4.2 V

Maintenance and servicing

Maintenance and cleaning
Use a soft cloth dampened only with water for cleaning. Do not use cleaning products of any kind.

• Have all repairs performed only by an authorized bike dealer.
  Do not clean any of the components with pressurized water.

Transport

• If you transport your bike attached to the outside of your car, e.g. on a bike rack, remove the SmartphoneGrip and the eBike battery to avoid damaging them.

After-sales service and advice on using products
If you have any questions about the eBike system and its components, contact an authorized bicycle dealer.
For contact details of authorized bike dealerships, please visit www.bosch- ebike.com.

Disposal

The drive unit, on-board computer incl. operating unit, battery, speed sensor, accessories and packaging should be disposed of in an environmentally correct manner.
Check that your personal data has been deleted from the device. Do not dispose of eBikes and their components with household waste.
Please return Bosch eBike components that are no longer usable free of charge to an authorized bicycle dealer.
Subject to change without notice.

Robert Bosch GmbH
72757 Reutlingen
Germany
www.bosch-ebike.com

References

• Bosch eBike Systems | Premium eBike systems & smart features - Bosch eBike Systems

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>