MAGNET BARON MK-A2 Questoris Imperial Knight No Drill Magnetization Kit Instruction Manual
- July 6, 2024
- MAGNET BARON
Table of Contents
- MK-A2 Questoris Imperial Knight No Drill Magnetization Kit
- Product Specifications:
- Product Usage Instructions:
- 1. Parts Identification:
- 2. Magnetization Process:
- 3. Magnetization Tools:
- 4. Part Preparation:
- 5. Magnet Attachment:
- 6. Additional Notes:
- Q: How do I ensure the magnets are aligned correctly during
- Q: Can I reuse the magnets if I need to disassemble the
- Q: What should I do if a magnet does not hold securely?
MK-A2 Questoris Imperial Knight No Drill Magnetization Kit
“`html
Product Specifications:
- Total Magnets: 36
- Magnet Diameter (mm): 2, 4, 5, 10, 12
- Magnet Thickness (mm): 1, 1.5, 2, 3, 4
Product Usage Instructions:
1. Parts Identification:
Each part in the kit has an alphanumeric code for
identification. Make sure to carefully identify and sort the parts
before starting the magnetization process.
2. Magnetization Process:
Follow these steps to magnetize the Questoris Knight model:
Step 1: Waist Joint
- Model Parts: Hip Cap (Questoris 84), Torso Bottom (25)
- Magnets Used:
- 1 x 10mm x 3mm
- 1 x 12mm x 2mm
Refer to the provided picture for visual guidance on this
step.
3. Magnetization Tools:
Ensure you have the necessary tools for magnetization, such as
tweezers, glue, and a marker for identifying codes on parts.
4. Part Preparation:
Before magnetizing, carefully remove parts from sprues. Use a
marker to highlight codes if they are difficult to see.
5. Magnet Attachment:
Attach magnets to the designated areas as per the provided
instructions. Ensure correct polarity alignment for proper
assembly.
6. Additional Notes:
For a detailed process on magnetizing specific parts like Armpit
Arms, Torso components, and Missile Pods, refer to the respective
codes and sizes mentioned in the manual.
Frequently Asked Questions (FAQ):
Q: How do I ensure the magnets are aligned correctly during
assembly?
A: To maintain proper alignment, mark one side of the magnet and
its corresponding placement area to ensure consistent polarity.
Q: Can I reuse the magnets if I need to disassemble the
model?
A: Yes, carefully detach the magnets using a flat tool and store
them properly for future use.
Q: What should I do if a magnet does not hold securely?
A: Reapply adhesive or glue to ensure a strong bond between the
magnet and the part.
“`
Questoris Knight Magnetization Instructions.
Please follow the normal assembly instructions as they come with the plastic
kit. The instructions below are only for the magnetization of the parts
pictured and do not show the full assembly process. In several pictures, the
parts are held together with double-sided tape or poster putty for
illustrative purposes.
To keep track of the polarity of the magnets, we use a set of Magnicator
tools. We may refer to the polarity of the magnets as “red” or “blue,” after
which magnicator is attracted to that magnet’s surface. If you do not have
those or similar tools, ensure you have some other method of tracking a
magnet’s polarity. For example, you might color one surface of a spare, large
magnet with a marker and reference back to it every time you use a magnet.
Possibly attach that large magnet to a tool that you can keep nearby but you
won’t need to use; A hammer or wrench, for example.
As of the time we are writing this guide, the box GW sells is called Questoris Knight. It can make the Imperial Knights Crusader, Errant, Gallant, Paladin, Preceptor, Warden, and the Chaos Knight Despoiler. We will refer to the knight you are building using this guide as the Questoris.
This article explains how to magnetize the Questoris Knight model using the kit from The Magnet Baron.
The kit comes with seven (7) sprues and a set of 36 magnets (potentially with some extras). The individual parts on the sprues have an alphanumeric code recessed into the part to help you keep track.
Magnet Diameter (mm) Magnet Thickness (mm) #
2
2
12
4
1.5
4
5
3
4
6
2
10
10
3
1
12
2
1
12
3
4
Total
36
Code Name
Magnet (mm) # Sprue
Kit
A1 Armpit Arm
12mm x 3mm 2 Medium Knight Shoulders
B
A2 Armpit Torso
12mm x 3mm 2 Medium Knight Shoulders
B
G1 Armpit Guide
–
1 Medium Knight Shoulders
B
A3 Stock Plug
5mm x3mm 1 Questoris Triple Gun Barrel
Q
A4 LasMel Plug
5mm x3mm 2 Questoris Triple Gun Barrel
Q
A5 BCan Plug
5mm x3mm 1 Questoris Triple Gun Barrel
Q
A6 Stock Side
4mm x 1.5mm 1 Questoris Triple Gun Side
Q
A7 Mel Side
4mm x 1.5mm 1 Questoris Triple Gun Side
Q
A8 BCan Side
4mm x 1.5mm 1 Questoris Triple Gun Side
Q
A9 Las Side
4mm x 1.5mm 1 Questoris Triple Gun Side
Q
G3 Stock Guide
–
1 Questoris Triple Gun Side
Q
A10 Missile Face
2mm x 2mm 2 Questoris Missile Pod
Q
A11 Missile Pod
2mm x 2mm 1 Questoris Missile Pod
Q
G4 Missile Pod Guide
–
– Questoris Missile Pod
Q
A12 Head Clamp
2mm x 2mm 1 Medium Knight Head Mount
B
A13 Head Pivot
2mm x 2mm 3 Medium Knight Head + Mount Sprues
B
A14 Torso Gun Clamp 2mm x 2mm 2 Medium Knight Shield & Sponson Weapons B
A15 Torso Gun Pivot 2mm x 2mm 3 Medium Knight Shield & Sponson Weapons B
A16 Torso Shield Pivot 2mm x 2mm 1 Medium Knight Shield & Sponson Weapons
A18 Bicep Ring
6mm x 2mm 6 Medium Knight Bicep Rings
B
A19 Head Face Shield
–
2 Medium Knight Head
B
A20L Head Side Left
–
2 Medium Knight Head
B
A20R Head Side Right
–
2 Medium Knight Head
B
A21L Head Hose Left
–
2 Medium Knight Head
B
A21R Head Hose Right
–
2 Medium Knight Head
B
A22R Q Bicep Main Left 6mm x 2mm 1 Questoris Biceps
Q
A22L Q Bicep Main Right 6mm x 2mm 1 Questoris Biceps
Q
Once the parts are carefully removed from the sprues, if the code is difficult to see, you can take a marker and pass it over the recessed code. It should be much more obvious afterwards.
Step #1
Waist Joint
Magnets Used Size
1 10mm x 3mm
1 12mm x 2mm
3D Printed Parts
None
Model Parts Hip Cap
Questoris 84
Torso Bottom
25
This is a picture of the model parts and the magnets used in this step. The hemisphere on the left is Part 84 from the
Knight Preceptor kit (now sold as the Questoris Knight Kit). The Abominant kit has this part incorporated with the lower
part called A67. The magnetization process should be the same.
The use of the Magnicators here is for illustrative purposes only, as the specific polarity is not important at this joint. The 10mm x 3mm magnet is inserted into the hemispherical piece on part A67, while the 12mm x 2mm magnet is placed onto the top of the waist hemisphere on the right part A88, aligned with the hole.
Once the magnets are in place, they should hold the parts together. We suggest putting some super glue first onto the magnet inside A67 inside the hemisphere. Once it is dry, you can put super glue onto the magnet on part A88 on the right. As this part has a hole, you should be careful to remove the left part so the glue does not drip onto A67.
Step 2A Magnets Used 3
3D Printed Parts None Model Parts Main Carapace Missile Pod Bottom Icarus
Autocannon Bottom
Questoris Carapace Weapons Size 5mm x 3mm
Code None Questoris 120 A28 A3
These are the magnets and parts from the Questoris Kit needed for this and the following step. Also shown is A24, the top of the missile pod, for convenience.
Glue a 5mm x 3mm magnet into the recess in A28 (Missile Pod bottom) and A3
(Icarus Autocannon bottom), both with the same polarity. (Here we use blue.)
Glue a 5mm x 3mm magnet on to the underside of part 120 (main carapace) in the
location beneath the spot where the carapace weapons connect.
When finished, the three parts should be able to stack as above. Complete the
assembly on the Icarus Autocannon and the main carapace as usual. Continue on
to magnetize the face plate of the Missile Pod.
Step 2B Magnets Used 3
3D Printed Parts Questoris Missile Pod (Sprue) Missile Face Pod Main Pod Guide
Model Parts Main Carapace Missile Pod Bottom Icarus Autocannon Bottom
Ironstorm Missile Face Stormspear Rocket Face
Questoris Missile Pod
Size
2mm x 2mm
Code
2
A10
1
A11
1
G4
Questoris
120
A28
A3
A31
A32
This is a rendering of the Questoris Missile Pod sprue.
These are the four 3D printed parts. The codes are highlighted with a marker
to make them easier to see.
Insert and glue the 2mm x 2mm magnets into A10 and A11 as illustrated above.
Note that the magnet polarity in A11 is similar to the large magnet in the
Missile Pod Bottom. Reversing the polarity in A11 may cause A11 to be repelled
from the Missile Pod Bottom. Ensure the magnet orientation is the same for
both A10 pieces.
It may be difficult to correctly position A11 in the front-center of the
Missile Pod Bottom. The alignment tool G4 is used to assist in the correct
positioning of A11. In the illustration above you can see that G4 grabs the
front edge of the Missile Pod Bottom piece and fits nicely once aligned with
the center.
The above photo shows how G4 fits onto the Missile Pod Bottom while holding
A11 in position. Be very careful not to get any glue onto G4!
Top view of G4 and A11 positioned on the Missile Pod Bottom.
Glue the A10 parts onto both front face parts, A31 and A32. The small `tongue’
on A10 fits into the recess on the bottom of the face parts. It will fit
snugly into A32 (smaller missiles) and stand off a bit on A31 (larger
missiles). This is normal, to allow both parts to mate with A11.
Top view of the magnetized parts. It is normal for there to be some between
the parts in some areas due to the parts being different.
Step 3 Magnets Used
4 (1 plus 1 per head)
3D Printed Parts Medium Knight Head (Sprue) Head Pivot Head Face Shield Head
Side Right Head Side Left Head Hose Right Head Hose Left Medium Knight Head
Mount (Sprue) Head Clamp Head Pivot
Model Parts Torso Front Head Right Head Left Hose Right Hose Left Face Head
Clamp Face Armor Shield
Knight Head Size 2mm x 2mm
2x Sprues per Kit allow three heads.
1 1 1 1 1 1 1x 1 1
Questoris 36 47 46 49 48 39 42 43, 44, etc.
Code
A13 A19 A20R A20L A21R A21L
A12 A13
The 3D printed sprues for the Knight Head magnetization.
All of the currently-produced medium Knight Kits come with a vast selection of
face shields. Some may seem more appropriate to specific weapon loadouts. Some
may just be fun. Instead of magnetizing the face shields with tiny drills and
tinier drill bits, our kit allows you to build THREE COMPLETE HEADS, which you
can swap out simply by popping the head off.
The plastic parts and one head’s worth of 3D printed parts. The second 3D
printed head is the same as the first, with a different face armor shield of
course.
The 3D printed parts have their codes highlighted with marker. We will use
three 2mm x 2mm magnets, with a fourth saved for the second 3D printed head.
Make sure to clean out the magnet recesses from any scrap piece of 3D printer
support. Using a tiny drop of super glue, carefully press the magnet into all
of the A13 pieces (head pivots) and the one A12 (head clamp). As A12 is
symmetrical, the magnet’s polarity doesn’t matter until it is installed onto
the Torso Front part.
A13 fits into the right-side head part (A20R and plastic part) as shown above.
Do not glue!
Assemble the rest of the head as normal. Again, do not glue A13 head pivot to
head left side (A20L or plastic part), but be sure to glue the head left side
to the head right side. After the head sides are glued, attach the head face
shield (A19 or plastic part) to the head assemblies and then attach the hoses
(A21R and A21L plus plastic parts) to the correct sides.
Use the magnet polarity on the top of the A13 head pivot parts to ensure the
A12 head clamp’s polarity is correct when gluing A12 to the Torso Front part.
Attach the face armor shields to the heads as desired.
Step 4
Magnets Used 4
8 (2 plus 1 per arm plus spares)
3D Printed Parts Medium Knight Shoulders (Sprue) Armpit Arm Recess Armpit Torso Recess Armpit Guide
Shoulders and Arms
Size
12mm x 3mm
6mm x 2mm
Code
1x
2
A1
2
A2
1
G1
Bicep Ring (Sprue) Bicep Magnet Rings Abominant Bicep (Sprue) Ab Bicep Main Right Ab Bicep Main Left
8 (5 plus spares) 1x 1 1
A18
A17R A17L
Questoris Bicep (Sprue) Q Bicep Main Right Q Bicep Main Left
Model Parts Torso Main Right Torso Main Left Bicep Pistons Shoulder 1 Shoulder
2 Arm Set 1 Arm Set 2 Arm Set 3 Arm Set 4
1 1
Questoris 105 106 91, 95 93, 94 90, 96 A11, A12 20, 21 34, 35 A54, A55
A22R A22L
The Medium Knight Shoulders sprue show above contains one guide G1 and two each of the Armpit Arm Recess A1 and Armpit Torso Recess A2.
The Questoris Biceps sprue contains two Questoris Biceps parts A22L and A22R.
They are identical and named L and R for convenience purposes. The Medium
Knight Biceps Ring sprue contains eight A18 Bicep Magnet Rings. While it is
unlikely that you will have enough arm weapons to use all eight of these
rings, the 6mm x 2mm magnets are very strong and often cause the parts to jump
and fly across the work bench resulting in the destruction of quite a few A18
magnet rings. You can easily glue A18 parts back together, but, just in case,
we have included spares.
This is a shot of the parts that we will use during this stage. Colors may
vary. The small clamps and poster putty are being used to orientate the parts
in order to show you where the codes are. They are not included. We will show
you where to put the magnets. It is up to you to assemble the rest of the
model’s plastic parts.
This is a rendering of the parts on one side of the knight. Notice the
polarity of the magnets is the same throughout the assembly, all the way from
the Arm part’s A18 to A22R to A1 and, finally, A2. The Bicep Piston part will
need to be shortened or possibly removed completely due to A1 blocking the
interior of the Shoulder part.
The first step is to cut the tabs off of the Torso Side parts and to file/sand
them down flat in order for the guide G1 to be able to fit flush on the side.
Insert the 12mm x 3mm magnets into parts A1 and A2. Ensure that the polarity
is compatible.
Glue A2 onto the Torso Side part, using G1 to locate the center. Be careful
not to glue G1 to the Torso Side or to A2! You can use a pin to poke G1 from
the back side to remove it from the Torso Side part.
Glue A1 with inserted magnet into the Shoulder assembly at the same time as
the Bicep part A17/A22. Be sure to orientate the Bicep as shown in the model’s
instructions. (For both kits currently released, the Bicep Piston is attached
to the recessed pivot point on the bottom-inside.) The Bicep Piston part, not
shown above, will need to be shortened or possibly removed completely due to
A1 blocking the interior of the Shoulder part.
Glue the 6mm x 2mm magnets into the A18 Bicep Rings. Insert the A18 parts into
one half of the Arm set pieces. You may need to file A18 to fit them into some
of the Arm set pieces. Important: DO NOT GLUE THE ARM SETS TOGETHER AT THIS
TIME. YOU WILL NEED TO INSERT THE WEAPON AT THE SAME TIME AS PER THE
INSTRUCTIONS. The following pictures show the arm sets together, but they are
only held together through friction or poster putty.
Glue the 6mm x 2mm magnets into the A17/A22 Bicep parts. Ensure that the
polarity is compatible with the magnets in A18 Bicep Rings. Again, the top Arm
Set assembly is NOT TO BE GLUED until you have the weapon completed as per the
model’s instructions.
Showing the Bicep and Shoulder parts magnetized but not assembled. At this
point, you can continue to assemble the Knight as per the instructions. Be
careful, as the magnets are very strong and will attract to each other,
potentially causing damage to the parts. (The above picture is about as close
as we were able to get them.)
Step 5
Magnets Used 6 (3 plus 1 per weapon)
3D Printed Parts Medium Knight Sponson Weapons (Sprue) Torso Gun Clamp Torso
Gun Pivot
Model Parts Heavy Stubber, Shroud Meltagun, Shroud Multi-laser, Shroud Torso
Main Left
Torso Weapons
Size
2mm x 2mm
Code 1x
2
A14
3
A15
Questoris 101, 98
A39, A40
26, 27 106
The Abominant Knight kit has one “sponson” weapon: a Heavy Stubber, although
several other options exist online or you can take one from another kit. (The
Questoris has three sponson weapons.) The Medium Knight Sponson Weapons Sprue
has two Torso Gun Clamps A14, to attach a magnet to the Knight’s torso plus
one for a friend, and three A15 Torso Gun Pivots; one for the Heavy Stubber
and two for other weapons to be named later.
The Questoris Knight kit has three “sponson” weapons: a Heavy Stubber, a
Meltagun, and a Multi-laser. The Medium Knight Sponson Weapons Sprue has two
Torso Gun Clamps A14, to attach a magnet to the Knight’s torso plus one for a
friend, and three A15 Torso Gun Pivots.
This picture shows one A15 Torso Gun Pivot and a Heavy Stubber with a shroud
Carefully insert the 2mm x 2mm magnets into the Torso Gun Clamp A14 and the
Torso Gun Pivot A15. Repeat for all of the A15 parts that you are going to
use. When gluing A14 onto the Torso Main Left, ensure that the polarity is
compatible with the magnet in A15.
A15 should clip onto the weapon without needing glue. Proceed to assemble the
weapons as shown in the instructions.
Step 6A
Magnets Used 4
3D Printed Parts Questoris Triple Gun Barrel (Sprue) Stock Plug LasMel Plug
BCan Plug
Model Parts Main Triple Gun Stock LasMel Shield Las Barrel Mel Barrel BCan
Shield Bcan Barrel HStub Side Detail
Questoris Triple Gun Barrel
Size
5mm x 3mm
Code
1x
1
A3
2
A4
1
A5
Questoris 22, 23
24 30, 31 18, 19
13
3, 4 7, 8
The Questoris Knight kit has three weapons that all share the same gun stock:
a rapid-fire battle cannon (BCan), a thermal cannon (Mel), and a Las-Impulsor
(Las). We’ll call this whole assembly “The Triple Gun.” Each of the weapon
types has a barrel, a shield, and a detail that goes on the side of the stock.
The BCan’s shield also has a Heavy Stubber with a side detail as well. The Mel
and Las weapons use the same shield.
The Questoris Triple Gun Barrel sprue has a magnet plug that goes into the
stock piece A3, two magnet plugs that go into the Las and Mel barrels A4, and
a plug that goes into the BCan barrel A5.
The Questoris Triple Gun Side sprue has a detail part that is glued to the
side of the stock A6, as well as detail alignment parts for the Mel side
detail A7, the BCan side detail A8, and the Las side detail A9. The stock side
detail part needs to be aligned precisely on the stock so we use the Triple
Gun stock guide G3. Please note: Several of the plastic pieces in the
following pictures are shown partially assembled, specifically the Triple Gun
Stock parts 22 and 23. DO NOT GLUE THE TRIPLE GUN STOCK AT THIS TIME BECAUSE
IT NEEDS TO BE ASSEMBLED WITH MANY OTHER PARTS. We show only the minimum basic
parts in the pictures for simplicity, but they need to be fully assembled as
per the instructions. (In these pictures we use double-sided tape, which is
helpful when dry-fitting.)
The parts for the Triple Gun barrel magnetization.
Glue the 5mm x 3mm magnets into parts A3, A4 x2, and A5 with recommended
polarity of A3 blue and A4 & A5 red. It is good to dry-fit the barrel plugs
before the stock and barrels are glued because they will need to be at very
specific depths in order to fit tightly together.
The above rendering shows the assembly of the BCan barrel, BCan shield, and
stock. A3 is glued flush with the surface of the stock. A5 is glued into the
BCan shield recessed far enough for the stock to fit fully inside the shield.
There is an arc on the back of the shield and front of the stock which should
fit tightly. The tab on the top of the barrel fits into the notch on the front
side of the shield.
The assembled parts, including the HStub side detail. Note: The stock is shown
assembled for reference. DO NOT ASSEMBLE THE STOCK AT THIS TIME.
The BCan magnets installed. The HStub detail should fit snug between the
shield and the stock. There is an arc on the back of the shield and front of
the stock which should fit snug. Continue to assemble BCan shield as per the
instructions.
The above rendering shows the assembly of the Las barrel, LasMel shield, and
stock. A3 is glued flush with the surface of the stock. A4 is glued into the
Las barrel to be flush with the surface. The LasMel shield fits in between the
barrel and stock.
The assembled parts. Note: The stock is shown assembled for reference. DO NOT
ASSEMBLE THE STOCK AT THIS TIME.
The Las magnets installed. There is an arc on the back of the shield and front
of the stock which should fit snug. Continue to assemble LasMel shield as per
the instructions.
The above rendering shows the assembly of the Mel barrel, LasMel shield, and
stock. A3 is glued flush with the surface of the stock. A4 is glued into the
Mel barrel to be flush with the surface. The LasMel shield fits in between the
barrel and stock.
The assembled parts. Note: The stock is shown assembled for reference. DO NOT
ASSEMBLE THE STOCK AT THIS TIME.
The Mel magnets installed. There is an arc on the back of the shield and front
of the stock which should fit snug. Continue to assemble LasMel shield as per
the instructions. Continue on to install the magnets on the side of the Triple
Gun Stock.
Step 6B
Magnets Used 4
3D Printed Parts Questoris Triple Gun Side (Sprue) Stock Side Mel Side BCan Side Las Side Stock Guide
Model Parts Main Triple Gun Stock Las Side Detail Mel Side Detail Bcan Side Detail
Questoris Triple Gun Side Detail
Size
4mm x 1.5mm
Code
1x
1
A6
1
A7
1
A8
1
A9
1
G3
Questoris 22, 23 32
15
10, 11, 14
The Questoris Knight kit has three weapons that all share the same gun stock:
a rapid-fire battle cannon (BCan), a thermal cannon (Mel), and a Las-Impulsor
(Las). We’ll call this whole assembly “The Triple Gun.” Each of the weapon
types has a barrel, a shield, and a detail that goes on the side of the stock.
The BCan’s shield also has a Heavy Stubber with a side detail as well. The Mel
and Las weapons use the same shield.
The Questoris Triple Gun Side sprue has a detail part that is glued to the
side of the stock A6, as well as detail alignment parts for the Mel side
detail A7, the BCan side detail A8, and the Las side detail A9. The stock side
detail part needs to be aligned precisely on the stock so we use the Triple
Gun stock guide G3.
Please note: Several of the plastic pieces in the following pictures are shown
partially assembled, specifically the Triple Gun Stock parts 22 and 23. DO NOT
GLUE THE TRIPLE GUN STOCK AT THIS TIME BECAUSE IT NEEDS TO BE ASSEMBLED WITH
MANY OTHER PARTS. We show only the minimum basic parts in the pictures for
simplicity, but they need to be fully assembled as per the instructions. (In
these pictures we use double-sided tape, which is helpful when dry-fitting.)
The plastic and 3D printed sprue. The 3D printed parts with the codes shown through the use of a black marker, and four 4mm x 1.5mm magnets.
The guide G3 fits tightly onto the side of the Triple Gun stock. Glue the 4mm
x 1.5mm magnet into A6 with a polarity compatible with A7, A8, and A9. Fit A6
into the slot on G3. Be careful not to glue G3 to the stock! Remove G3 once A6
is glued.
Glue the 4mm x 1.5mm magnets into A7, A8, and A9 with a polarity compatible
with the magnet in A6. Glue the parts into the BCan detail, Las detail, and
Mel detail as shown in the above rendering and the following pictures.
The BCan detail fits tight on the side of the partially-assembled stock. The BCan detail fits tight on the side of the partially-assembled stock.
The Las detail fits tight on the side of the partially-assembled stock. The Las detail fits tight on the side of the partially-assembled stock.
The Mel detail fits tight on the side of the partially-assembled stock.
The Mel detail fits tight on the side of the partially-assembled stock.
Continue to assemble the rest of the Knight as per the instruction book.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>