Swissbrand BP-901 TWS Earbuds User Manual
- June 24, 2024
- SWISSBRAND
Table of Contents
User Manual
FCC ID: 24320-8P801
TWS Earbuds
BP-901, 4SN023A, 4SN023ATOL
PRODUCT KEY
- Earbud indicator light
- Multi Function Bution(MFB)
- Case LED light
- Type-C USB input
CONTROLS
Charge the earbuds.
Put the earbuds into the charging case, the earbuds wil be charged
‘automatically. The red status LED fight il be on during charging and Wil turn
off when fully charged.
Charge the charging box
Use a Type-C cube connected to a USB charger (DG 5V-14)
‘The Steps for dual earbud pairing (First use only)
Take out both earbuds from the charging case at the same time. The
LED lath on both earbuds wil be flashing blue and red. One of the: ‘carbuds
LED will turn off after 2 seconds. This means that both ‘earbuds are ready to
pair. Tum on the Bluetooth on your device and search for @ new device then
select “Swiss brand vibe” o connect.
How to re-connect
‘The earbuds wil automatically y o re-connect with the last paired Gevice
after re-start. Ifnot put the earbuds back into charging case. ‘andtry again,
or connect manually
EARBUD BUTTON FUNCTIONS
Power ON: Press+hoid(3s) R carbud
Power OFF: Press +hold(5s) LR earbud
PlayPause: Press once R earbud
Increase Volume: 2« Press R carbud
Decrease Volume: 2x Press L earbud
Next Track: Press +hoki(1.55) R earbud
Previous Track: Press+hold(1.5s) L earbud
Activate Voice Assistant: 3x Press LR carbud
ANSWER/END/REJECT INCOMING CALLS
Answer/End: Press once L/R earbud when incoming calls Reject: Press+hold(2s) L/R earbud
FREQUENTLY ASKED QUESTIONS
The smartphone cannot find the wireless earbuds
Check whether the earbuds power is switched on or not. Does the status LED
light flash red and blue alternatively? If the wireless earbuds still haven’t
been found after switching power on, please restart both the earbuds and the
bluetooth search on your phone.
There is something wrong with the wireless earbuds while using them Please try
to re-connect with the smartphone after turning it on and restarting the
earbuds. Check the charging status of the earbuds by putting them into the
charging box until the red LED indicator is on. Then take them out and let
them try to re-connect with your device.
The wireless earbuds always disconnect or make noise when connected to
smartphone
The wireless earbuds power status is low, please re-charge it. There is an
obstruction between the mobile device and the wireless earbuds, or the
wireless distance is beyond the signal range. Please do not cover the wireless
earbuds with your hands in order to maintain the continuous stability of the
signal. Try to keep the wireless earbuds and the smartphone in the same
direction.
FCC Statement
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates. uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there
is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver. – Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. – Consult the dealer or an experienced radiofTV
technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>