FUNMAS 30861 3-in-1 Indoor Dryer Vent User Manual

FUNMAS 30861 3-in-1 Indoor Dryer Vent

WELCOME
Thank you for choosing FUNMAS. We are committed to product quality and friendly customer service. If you have any questions or suggestions, please don’t hesitate to contact us.

Product Contents

Introduction

• Your FUNMAS dryer vent should be located on a vertical wall as close as possible to the electric clothes dryer.
• It should not be exhausted into an attic, soffit, ridge vent or crawl space. It should be installed at a height convenient to the operator that will be easy for the user to access, clean and maintain. We recommend that the exhaust line be any UL listed dryer transition duct. Vinyl flex ducts should never be used.
• The connection at the back of the dryer may be made with a metal 90 degree fitting known as a “close elbow” to prevent the transition hose from being crushed against the wall.

Installation

Dryer Vent Mein Body

1. STEP 1
   Remove FUNMAS Unit from Packaging.

2. STEP 2
   Select a wall close to the dryer which allows you to meet the recommendations above.,

3. STEP 3
   Release the door latches and open the door. Steady the FUNMAS dryer vent against the wall and mark the screw locations.

4. STEP 4
   If the wall is concrete or plaster, drill a 1/4″ hole at screw locations 11/2″deep and tap in the plastic anchors.

5. STEP 5
   If the wall is sheetrock, drill a 3/16″hole and tap in the plastic anchors.

6. STEP 6
   Position the FUNMAS dryer vent to align with the anchors and screw to the wall.

Installation Installing the exhaust line (not included)

1. STEP 1
   Determine if your dryer has a sidewall option for ducting. Choose a connection that will provide the shortest path. This might be the back of the dryer cabinet or sidewall.

2. STEP 2
   If the connection is at the back of the dryer cabinet, slide the dryer away from the wall and install a metal 90 degree fitting( close elbow).

3. STEP 3
   Stretch out a small portion of the metal flex duct and make connection to the close elbow. Secure with hose clamp.

4. STEP 4
   Carefully lead the metal flex duct towards your FUNMAS dryer vent and make connection. Secure with hose clamp .

5. STEP 5
   Your FUNMAS dryer vent is now installed and ready for calibration.

Calibrating the Safety Exhaust Flap

• The Safety Exhaust Flap(SEF) is designed to alert the homeowner that the filter is completely loaded and needs to be cleaned or replaced. It remains in the open position until reset by the user. The SEF needs to be calibrated by the homeowner using weights (included) to match the exhaust output of the dryer.
• The FUNMAS dryer vent comes with 5 weights, each weighing 5 grams. You will use the weights to weight the SEF in order to keep it closed.

Calibrating the Safety Exhaust Flap

1. STEP 1
   Make sure that you have cleaned the screen inside your dryer. This should be done after each dryer load as recommended by the manufacturer.

2. STEP 2
   Take a weight and attach it to the inside of the Safety Exhaust Flap.

3. STEP 3
   Find a book, notebook, clipboard or magazine. Turn your dryer on and cover about 25% of the door.

4. STEP 4
   What should happen now is that either your Safety Exhaust Flap will open or stay closed. If it stays closed, continue to move upwards until the flap opens.

5. STEP 5
   If it opens before you reach 80% coverage of the door, add another weight to the top of the Safety Exhaust Flap and do the test again. Continue to add weights, as needed, until Safety Exhaust Flap opens at 80% coverage. Most users do not have to add more than 2 weights.

Operating Instructions Polyester Filter

• Your FUNMAS dryer vent has been designed for easy maintenance. It is necessary that the user clean and service the FUNMAS dryer vent as part of a regular laundry room routine.
• Your FUNMAS dryer vent contains a screen filter and a polyester filter. The screen filter collects lint, pet hair and other large debris and serves to extend the life of the polyester filter. The polyester media filter is specifically designed to keep fine lint dust from entering the indoor environment.
• Polyester filters are installed with blue side to the INSIDE of the vent and placed between the removable screen and the door. You should see the white side of the polyester filter when the door is closed.

Use of water drawer
The water drawer has a maximum water storage level mark. When using, the water level should not exceed this mark.

It can be used as an aromatherapy machine by dripping in the aromatherapy liquid. Purify indoor air.

Cleaning

• Cleaning the screen filter is easy. Simply release the door latches, open the door.
• While leaving the screen in place, remove the accumulated lint with a sweeping motion of the hand or use tools scrape the lint off the back of the filter.
• If you use water drawer system, remove water drawer from the dryer vent, empty the water and lint from the unit.
• Refill the water and put it back in the dryer vent.

WARNING! Clean the screen frame every 3-5 dryer loads. The polyester filter can be lightly vacuumed or replaced every 5-8 dryer loads. Do not wash.

Disclaimer Statement
FUNMAS dryer vent can protect the indoor air quality of households where residents are unable to vent their electric clothes dryer to the outside of the home. The purchaser acknowledges that the FUNMAS dryer vent requires routine and regular maintenance, and the user assumes all responsibility and liability for proper installation, maintenance, and use. If you have questions or concerns about your FUNMAS dryer vent please contact us by email. We will serve you wholeheartedly.

Visit funmas_service@outlook.com and we will bring you sincere service.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>