SENDRY ‎MCS-001 Rechargeable Handheld Small Electric Saw User Manual

SENDRY ‎MCS-001 Rechargeable Handheld Small Electric Saw

Launch Date: June 15, 2024
Price: $49.99

GENERAL SAFETY RULES (FOR ALL BATTERY OPERATED TOOLS)

WARNING :
Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal

Work Area Electrical Safety

1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
2. Do not operate power tools in explosive atmospheres. such as in the presence of flammable liquids, gasses, or dust. Power tools create sparks that may ignite the dust of fumes
3. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.
4. A battery-operated tool with integral batteries or a separate battery pack must be recharged only with the specified charger for the battery. A charger that may be suitable for one type of battery may create a risk of fire when used with another battery.
5. Battery operated tool only can be used with specifically designated battery pack. Using any other batteries may create a risk of fire.

Personal Safety

1. Stay alert, watch what you arc doing, and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
2. Dress properly. Do not wear loose clothing or jewelry, contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
3. Avoid accidental starting. Be sure switch is in the locked or off position before inserting battery pack. Carrying tools with your finger on the switch or inserting the battery pack into a tool with the switch on invites accidents.
4. Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.
5. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable better control of the tool in unexpected situations.
6. Use safety equipment. Wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

Tool Use and Care

1. Use clamps or other practical way to secure and support the workplace to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.
2. Do not force tools. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.
3. Do not use the tool if the switch does not turn it on or off. A tool that cannot be controlled with the switch is dangerous and must be repaired.
4. Disconnect the battery pack from the tool or place the switch in the locked or off position before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally.
5. Store idle tools away from children and other untrained persons. Tools are dangerous in the hands of untrained users.
6. When the battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, bums, or a fire.
7. Maintain tools carefully. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edge are less likely to deviate and are easier to control.
8. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation of damaged, ensure the tool is serviced before using. Many accidents are caused by poorly maintained tools.
9. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may create a risk for injury when used on another tool.

SCOPE OF APPLICATION

CUTTING TREES IN ORCHARDS, PRUNING BRANCHES IN MUNICIPAL GAR – DENS, CUTTING BAMBOO, AND CHOPPING FIREWOOD AT HOME, ARE NECESSARY FOR OUTDOOR LEISURE AND PERSONAL PROTECTIVE EQUIPMENT

Specifications

• Brand : DIKAKO
• Power Source : Battery Powered
• Horsepower : 150 Watts
• Item Weight : 2.63 Pounds
• Product Dimensions : 15.5 inches Length x 4.7 inches Width x 2.95 inches Height
• Chain Length : 6 Inches
• Chain Speed : 16.4 Feet per Second (FT/S)
• Manufacturer : DIKAKO
• UPC : 794261683736
• Part Number : MCS-001
• Item Model Number : MCS-001
• Batteries : 2 Lithium Ion batteries required (not included)
• Size : 6-Inch
• Color : Blue
• Voltage : 21 Volts
• Wattage : 500 Watts
• Type of Bulb : LED
• Batteries Included? : No
• Batteries Required? : Yes (2 Lithium Ion batteries required)
• Battery Cell Type : Lithium Ion
• Chain speed: 5m/s
• Type of guide plate: Chain wheel type
• Number of battery packs: 1-2
• Length of guide plate: 4″/8″/10″
• Fast charging :1.5 (3) hour

Package Includes

• 1 x Mini Chainsaw
• 2 x 21V 7500mAh Lithium Batteries
• 2 x Chains (one pre-installed)
• 1 x Wall Charger
• 1 x Nut Driver
• 1 x Sharpener
• 1 x Screwdriver
• 1 x Instruction Manual
• 1 x Gloves
• 1 x Protective Goggles
• 1 x Tool Box for easy storage and portability.

Dimension

Features

Rechargeable and Cordless Operation:

• Powered by a 21V 7500mAh lithium battery for cordless convenience.
• Allows for unrestricted movement during use without the limitations of cords.

Compact and Lightweight:

• Weighs only 2.63 pounds (including batteries), making it easy to handle and maneuver.
• The ergonomic handle design ensures comfort during prolonged use, suitable for one-handed operation.

Versatile Blades and Efficient Cutting:

• Uses a high-hardness 6-inch chain optimized for cutting hard and thick woods.
• Chain speed up to 10m/s ensures fast cutting, capable of handling larger wood diameters (up to 5 inches) efficiently.

Premium Motor:

• Features a pure copper motor for strong power and stable operation.
• Operates quietly with reduced friction, ensuring smooth cutting and minimal maintenance.
• Maximum motor speed of 8000 rpm enhances cutting efficiency.

Durable Battery with Fast Charging:

• Large-capacity lithium battery provides extended working time (60-90 minutes).
• Fast charging capability with a charging time of 1.5-3 hours.
• Triple intelligent protection system guards against overload, overage, and explosion, ensuring battery safety and longevity.

Safety Features:

• Requires simultaneous pressing of the safety lock and switch button to start, preventing accidental activation.
• Anti-splash baffle adjustable from 0° to 90° to control wood chip direction and protect the user.
• Includes goggles, gloves, and a safety harness for added protection during operation.

LED Light (Optional):

• Some models may include LED lights for enhanced visibility in low-light conditions, improving cutting precision.

Wide Application:

• Suitable for various cutting tasks including wood cutting, branch trimming, and home improvement projects.
• Ideal for use in gardens, farms, parks, and forests, catering to diverse cutting needs.

Package Contents:

• Includes 1 mini chainsaw, 2 batteries, 2 chains (one pre-installed), wall charger, nut driver, sharpener, screwdriver, instruction manual, gloves, protective goggles, and a tool box for convenient storage and portability.

Professional Service:

• SENDRY offers dedicated customer support and ensures high-quality service for user inquiries and product assistance.

Installation INSTRUCTIONS

1. CHARGE THE BATTERY, THE RED LIGHT IS ON WHEN CHARGING, AND THE GREEN LIGHT IS ON WHEN THE BATTERY IS FULLY CHARGED.
2. INSTALL THE CHAIN ACCORDING TO THE OPERATION DRAWING. NOTE REMOVE THE BATTERY PACK DURING THE INSTALLATION AND REMOVE OF THE GUIDE PLATE
3. AFTER INSTALLATION, START THE MACHINE WITH NO LOAD AND OBSERVE THAT THE MACHINE RUNS NORMALLY.
4. SHOULD NOT BE TOO USED FOR CUTTING, ACCORDING TO THE ACTUAL CUTTING SITUATION, FIRST SMALL AND THEN LARGE.
5. Remove the sprocket cover.
6. Assemble the saw chain along the guide bar. distant data SENDRY
7. Adjust the tension of the chain. (If the chain saw is loose during use and cannot be tightly attached to the guide bar, you can also adjust here to tighten the chain.)chain. (If the chain saw is loose during use and cannot be tightly attached to the guide bar, you can also adjust here to tighten the chain.)
8. Tighten the nut with the wrench.
9. Place the chain around the sprocket and ensure lines up with the pin. Please note!!! The chain saw must be installed in the correct direction.
10. Insert the battery pack into the slot at the bottom.

Charging Instructions

As shown in the picture, the charging hole of the battery is in the middle of the battery, insert the charging hole, and then connect the wall charger to the socket, it can be fully charged in about 1.5 to 3 hours.

How to Oil the Chain

1. Step 1: Cleaning
   Before adding lubricating oil, it is necessary to clean the dirt on the chain. Use a wipe to thoroughly clean the surface and crevice of the chain.

2. Step 2: Lubricate the chain
   Use an oil bottle to add lubricating oil to the chain, wait for 2-5 minutes after oiling to allow it to fully penetrate into the interior, and then turn the chain several times to make the lubricating oil evenly distributed on the chain, and then wipe off the excess oil with a dry cloth.

3. Step 3: Maintenance
   When the chainsaw is working, lubricating oil every 10 minutes can not only maintain the guide plate but also the chain.

Use Sharpener to Sharpen the Chain
When the chain becomes unsharp, the serrations can be rested using the included sharpener to keep the serrations sharp. When using the sharpener, grind along the direction of the sawtooth, not in the opposite direction, and the angle between the sharpener and the chain should not be too large, 30° is the best.

NOTICE
The load force of the mini chainsaw is relatively small. If the external force increases, it will cause the following problems:

1. When the section of the cutting object is too large, the cutting speed should be slowed down.
2. Excessive pressing force during cutting will increase the current and output power, causing the motor to heat up, which will cause smoke and a burnt smell first. Long-term load use may cause the motor temperature to be too high and the work will be suspended.
3. Chain wear leads to passivation, the board contains a lot of miscellaneous wood cores or the moisture content is too large, the wood is too hard, or the chainsaw load exceeds the limit to burn the coil, which may cause smoke, and the most likely condition is the chain problem, replace the new chain Or clean the chain and use it evenly.

Troubleshooting

correctly inserted and charged
| Safety lock not engaged properly| Press safety lock and switch button simultaneously
| Faulty switch or electrical connection| Check switch and connections; replace if necessary
Chain stops during operation| Chain tension too tight or loose| Adjust chain tension as per user manual instructions
| Chain stuck or jammed in wood| Release tension, remove debris, and reset chain
| Motor overheating| Allow chainsaw to cool down; check ventilation
Poor cutting performance| Dull chain| Sharpen or replace chain
| Incorrect chain lubrication| Ensure chain oil reservoir is filled and functioning
| Incorrect cutting technique| Follow proper cutting techniques and angles
Battery drains quickly| Battery aged or damaged| Replace with new or fully charged batteries
| High power consumption| Adjust cutting speed; reduce workload if possible

Pros and Cons

Pros

• Portability : Compact and lightweight design for easy handling
• Efficiency : High motor speed for efficient cutting
• Cost-Effective : Rechargeable battery reduces waste and cost
• Versatility : Suitable for various cutting tasks

Cons

• Limited Cutting Capacity : Limited to cutting materials up to 1-1/2 inches (38 mm) thick
• Battery Life : Battery life may be shorter than expected
• Noise Level : May be noisy during operation

Customer Reviews

• Rating : 4.5/5
• Review : “I was impressed with the saw’s performance and ease of use. It’s perfect for small cutting tasks.” – John D.
• Review : “I love the rechargeable battery feature. It’s eco-friendly and cost-effective.” – Emily K.

Contact Information

• Phone : 1-800-SENDRY
• Email : support@sendry.com
• Website : sendry.com

Warranty

• Duration : 1-year limited warranty
• Coverage : Covers manufacturing defects and malfunctions
• Claims : Contact SENDRY customer support for warranty claims

FAQs

What is the power source of the SENDRY MCS-001?

The SENDRY MCS-001 is powered by a rechargeable lithium-ion battery.

How much power does the motor of the SENDRY MCS-001 generate?

The SENDRY MCS-001 features a powerful motor with 150 Watts of output.

What is the maximum chain speed of the SENDRY MCS-001?

The SENDRY MCS-001 operates at a maximum chain speed of 16.4 feet per second.

How long does it take to fully charge the battery of the SENDRY MCS-001?

The SENDRY MCS-001 can be fully charged in approximately 1-2 hours.

What is the maximum cutting depth of the SENDRY MCS-001?

The SENDRY MCS-001 can cut through wood with a diameter of up to 5 inches.

How much does the SENDRY MCS-001 weigh?

The SENDRY MCS-001 weighs approximately 2.63 pounds, making it lightweight and easy to handle.

What is included in the package when you purchase the SENDRY MCS-001?

The SENDRY MCS-001 package typically includes the electric saw, rechargeable batteries, charger, chains, safety goggles, gloves, and a tool kit.

How does the SENDRY MCS-001 handle in terms of noise levels during operation?

The SENDRY MCS-001 operates with low noise levels, providing a quieter cutting experience.

What type of maintenance does the SENDRY MCS-001 require?

Regular maintenance includes cleaning sawdust and debris, sharpening or replacing chains as needed, and ensuring the battery is properly charged.

Does the SENDRY MCS-001 have LED lights for improved visibility?

Some models of the SENDRY MCS-001 feature LED lights to enhance visibility in low-light conditions.

What is the chain length of the SENDRY MCS-001?

The SENDRY MCS-001 has a 6-inch chain length, suitable for cutting small to medium-sized branches and logs.

What is the power source of the SENDRY MCS-001?

The SENDRY MCS-001 is powered by two 21V 7500mAh rechargeable batteries, providing long battery life and fast charging capabilities.

What safety features does the SENDRY MCS-001 have?

The SENDRY MCS-001 features a safety lock and switch button to prevent accidental start, a baffle to prevent debris splashing, and safety goggles and gloves for enhanced protection.

Video-SENDRY ‎MCS-001 Rechargeable Handheld Small Electric Saw

Download this manual:SENDRY ‎MCS-001 Rechargeable Handheld Small Electric Saw User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>