SUNCO LIGHTING 33750 Lumens 250W LED Area Light 5000K Installation Guide

Table of Contents

Specifications

MOUNTING TYPE: Slipfitter, Square Mount, Round Mount, Wall Mount, Yoke Mount
ACCESSORY: Various mounting accessories as listed
WIRING CONNECTION: L 129.5W60H88 upper bracket + L 138W60H88 lower bracket + L44.5W115H49 bracket
Note: Two dimming wires in the driver box

Installation Guide

Square/Round Pole Mount

Remove the side plate from the mounting bracket.
If mounting onto a round pole, attach the round pole mounting plate on the mounting bracket.
Route the cord into the mounting bracket through the hole for wiring, slide the fixture onto the bracket, and tighten 2 bottom screws.
Ensure the hole on the bracket is sealed by a silicon gasket by slightly dragging the wires.
Make wiring connections as per the wire diagram provided, replace the side plate, and fasten screws.

Slipfitter Mount

Wall Mount

Remove the side plate by loosening the screws.
Fix the back plate onto the arm bracket with provided screws.
Use the metal template provided to locate the footprint on thewall to drill holes, then fix the bracket on the wall with screws.
Route the power cord into the wall mount bracket, slide the fixture onto the mounting bracket, and tighten bottom screws.
Make wiring connections inside the bracket and replace the side plate with screws.

Yoke Mount

Mount the fixture onto a surface using the hole pattern provided on the trunnion bracket.
Loosen center bolts and set screw.
Rotate the fixture to the desired aiming position and tighten center bolts.
Make wiring connections as per the wire diagram provided.
After fixing the bracket at a certain angle, lock the four hexagon socket screws using a manual wrench.

Accessory List

MOUNTING TYPE	ACCESSORY	SPECIFICATION	QUANTITY

Frequently Asked Questions (FAQ)

Q: Can I use this LED Area Light for indoor applications?
A: The LED Area Light is designed for outdoor use. It is not recommended for indoor applications.
Q: Are replacement parts available for this product?
A: Yes, replacement parts are available. Please contact our customer service for assistance with ordering replacement parts.

WARNING – READ ALL INSTRUCTIONS BEFORE ATTEMPTING! INSTALLATION.

To prevent personal injury or product damage only licensed electricians should install.
To avoid electric shock or component damage disconnect power before attempting installation or servicing.
This product must be installed by the National Electric Code (NEC) and all applicable federal, state and local electric codes and safety standards.
Disconnect the product and allow cooling before servicing.
Any alteration or modification of this product is expressly forbidden as it may cause serious personal injury, death, property damage and/or product malfunction.
To prevent product malfunction and/or electrical shock this product must be properly grounded.
This luminaire is designed to operate in ambient temperatures ranging from -40°F to 104°F and to be horizontally mounted with the LEDs facing down.
This product must be installed by the applicable installation code by a Person familiar with the construction and operation of the product and the hazards involved.
MIN 167°F SUPPLY CONDUCTORS
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE THE CORRECT BRANCH CIRCUIT CONDUCTOR
CAUTION – RISK OF FIRE
Slipfitter/Yoke Mounted with PHOTOCELL function lilt angle should not exceed 15 degrees
This product is not available for several special environments, such as places with corrosive gas liquids or high-pressure water vapor.

Square/Round Pole Mount

Remove the side plate from the mounting bracket. Please skip to step 3 if mounted onto the square pole.
Attach a round pole mounting plate on the mounting bracket.
Route the cord into the mounting bracket through the hole for wiring, slide the fixture onto the bracket, and tighten 2 bottom screws.
Slightly drag the wires to make sure the hole on the bracket is sealed by a silicon gasket.
Make the wiring connection as per the wiring diagram below, replace the side plate, and fasten the screws.

Slipfitter Mount

Remove the side plate by loosening the screws.
Fix the back plate onto the arm bracket withscrews provided.
Use the metal template provided to locate the footprint on the wall to drill the holes, then fix the bracket on the wall with screws.
Route the power cord into the wall mount bracket, slide the fixture onto the mounting bracket, then tighten the bottom screws.
Make wiring connection inside of bracket and replace the side plate with screws

Yoke Mount

Mount the fixture onto the surface using the hole pattern provided on the trunnion bracket.
Loosen the center bolts and set screw.
Rotate the fixture to the desired aiming position and tighten the center bolts.
Make a wiring connection as per the wire diagram below.
After fixing the bracket at a certain angle, the four hexagon socket screws should be locked by a manual wrench.