BOSCH SMV4HCX48E Fully Integrated Dishwasher User Guide

BOSCH SMV4HCX48E Fully Integrated Dishwasher User Guide

Before using for the first time, read the instruction manual and the safety information it contains.

Setting up Home Connect

Tip: Connect your appliance to a mobile device. You can conveniently change all settings using the Home Connect app.

1. Install the Home Connect app on your mobile device and follow the instructions.
   

2.  Scan the QR code with the Home Connect app.

Overview of water hardness settings

You can find an overview of thewater hardness values that can be selected here.
A table of country-specific units can be found in the instruction manual.

How to use your appliance

1. Load the tableware.
   Only clean tableware that is suitable for dishwashers. Remove large remnants of food from the tableware. Check that the spray arms can rotate freely.

2. Add detergent.

3. Switch on the appliance .

Overview of water hardness settings

You can find an overview of the water hardness values that can be selected here.
A table of country-specific units can be found in the instruction manual.

You can find an overview of the water hardness values that can be selected here.
A table of country-specific units can be found in the instructionmanual.

Adding special salt

To avoid damage to the appliance, only add special salt to the dispenser for special salt just before the programme starts.

1. Unscrew the lid of the dispenser for special salt and remove.

2. On initial start-up: Fill the dispenser right up with water.

3.  Add the special salt to the dispenser. The water in the dispenser is displaced and forced out. Never add detergent.
   

4. Place the lid back on the dispenser and turn to close.

Programmes

The programme data has been measured in the laboratory according to
European standard EN 60436.
The consumption figures depend on the programme and additional function selected.
The runtime will change if the rinse aid system is switched off or rinse aid needs to be added.

How to use your appliance

1. Load theOnly clean tableware that is suitable for dish- washers. Remove large remnants of food from the tableware. Check that the spray arms can ro- tate freely.

2. Add

3. Switch on the appliance  .

4. Select the

5. Start the programme .

6. Remove the tableware at the end of the pro-To cancel the programme, press for 4 seconds.

7. The programme is cancelled and ends after ap- prox. 1 minute.

Cleaning filters

1.| After each wash check the filters for residue.
2.| Turn the coarse filter anticlock-|

2

 | wise       and re-|
 | move the filter|
 | system .|
 |  | 1

Pull down the mi- cro filter to re- move
Press the locking catches together and lift the coarse filter out

5. Clean the filter elements under running
6. Re-assemble the filter
7. Insert the filter system into the appliance and turn the coarse filter clockwise. Make sure that the arrow markings match

Cleaning spray arms

1. Unscrew the upper spray arm and pull down to remove .
   

2. Pull up the lower spray arm to remove
   

3. Check the outlet nozzles on the spray arms for blockages un- der running water and remove any foreign

4. Insert the lower spray

5. The spray arm clicks into position.

6. Insert the upper spray arm and screw it firmly in

Clean wastewater pump

1. Disconnect the appliance from the power
2. Remove the filter
3. Scoop out any

Prise off the pump cover using a spoon and grip it by the crosspiece

5. Lift the pump cover inwards at an angle and
6. Remove any remnants of food and foreign bodies in the area of the
7. Insert the pump cover and press down    .                                                                                                     2

a The pump cover clicks into position

Troubleshooting

Fault

Cause and troubleshooting E:32-00 will light up alternately or indicator for
water supply lights up

Cause and troubleshooting

Supply hose is kinked.
▶ Install the supply hose without kinks.
Water tap is turned off.
▶ Turn on the water tap.
Water tap is jammed or furred up.
▶ Turn on the water tap.
The flow rate must be at least 10 l/min when the water supply is open.

The filters in the water connection of the supply or AquaStop hose are blocked.

1.  Switch off the appliance.

2. Pull out the mains plug.

3. Turn off the water tap.

4. Unscrew the water connection.

5. Remove the filter from the supply hose
   

6. . Clean the filter.

7. Re-insert the filter in the supply hose.

8. Screw the water connection back on.

9. Check the water connection for leaks.

10. Restore the power supply.

11. Switch the appliance on.

Fault Cause and troubleshooting

E:92-40 will light up alternately.
Filters are soiled or blocked.
▶ Clean the filters.
E:61-02 will light up alternately.
Wastewater pump is blocked.
▶ Clean the wastewater pump.
Cover of the wastewater pump is loose
▶ Secure the cover of the Wastewater pump so it clicks into position. Remnants of food on tableware.
Tableware is placed too close together or basket is overfilled.

1.  Arrange tableware with sufficient space in between. The spray jets must reach the surfaces of the tableware.

2.  Avoid points of contact. Spray arm rotation is blocked.
   ▶ Arrange tableware so that it does not obstruct spray arm rotation. Spray arm nozzles are blocked.
   ▶ Clean the Spray arms. Filters are soiled.
   ▶ Clean the filters. Filters are inserted incorrectly and/or not engaged.

3. Insert the filters properly.

4. Engage the filters.
   Washing programme selected too weak.
   ▶ Select a more intensive washing programme

Read More About This Manual & Download PDF:

References

• Welcome to MyBosch

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>