DMDPET MH66 Pet Drying Box User Manual
- June 8, 2024
- DMDPET
Table of Contents
MH66 Pet Drying Box
User Manual
Please read this manual carefully before use
Attention Please read this manual carefully before using the product and keep it properly
- Do not disassemble the equipment without permission. Improper operation may cause electric shock or fire.
- To avoid the risk of electric shock, please do not use it in humid and humid environment.
- Please do not store this product in humid environment for a long time.
- It is forbidden to touch the live switch with wet hands, and it is forbidden to pull or plug the power plug with wet hands to prevent electric shock.
- Please use the voltage and frequency conforming to international standards. Otherwise, it may cause serious consequences such as equipment damage and even fire.
- If your equipment is abnormal, please feel free to contact our company after sales.
Product list
After opening the equipment package, please confirm whether the equipment is in good condition, and confirm whether the accessories _ are complete according to the following figure.
Product introsuction
APP operation
The device can be configured only in the 2.4G Wi-Fi band.
https://smartapp.tuya.com/smartlife
-
Download Smart Life Scan the QR code on the right, click the menu in the upper right corner, and in the browser.
Open the page to download, register and log in. (For Android/Apple users)
Android users can also search and download “Smart Life” in the mobile phone mall, and register and log in. -
Connect the drying box
Plug in the drying box, turn on Bluetooth on the mobile phone, click on the upper right corner @ and select Add Equipment.
In the scanned equipment list, find “DMDPET-Intelligent Drying Box” and click “Connect”. According to the interface prompt, enter the password of wireless network to enter the drying box operation interface.
The device can only be connected in the 2.4G Wi-Fi band. Please ensure that the router is connected in the 2.4G Wi-Fi band; otherwise, the device cannot be connected.After the network is configured, daily use is not affected by the Wi-Fi frequency band.
Daily cleaning
Turn off the equipment and pullout the power cord;| Lifting the drain board
upward;
Remove the drain plug and dry the water with a rag;| Install the drain plug
back, close the drain board and install it.
Rotate the net cover and take out the filter cotton. After cleaning and drying. install it back to the equipment.
Instructions for use
Turn on
After plugging in the power supply,
the device enters “standby mode”.
Unlock/Lock
Press the Start/Pause key for a long time to unlock/lock the drying box.
Open the hatch
Click the power button to open the hatch.
Mode switching
- Click the mode button and switch cyclically according to the mode shownbelow;
- Start running: After selecting the mode, click the Start/Pause oi button to start running.
Drying mode
In the drying process, the temperature, air volume and time can be adjusted as needed.
- Click the Mode button to switch to the desired drying mode;
- Click the temperature button adjust the temperature through the – increase or decrease key , and then press the temperature button to determine;
- Click the air volume button to adjust the air volume, and then press the Start/Pause button © to determine;
- Click the time button adjust the time through the increase or decrease key , and then press the time button to determine;
- After the setting is completed, click the Start/Pause button to start running.
- After drying, the hatch opens automatically.
Cat house mode
- Click the mode button to switch to the desired cattery mode;
- Click the air volume button to adjust the air volume, and then press the Start/Pause button to determine;
- After the setting is completed, click the Start/Pause button to start running.
Care model
- Click the conservation button to switch to the conservation mode;
- After the setting is completed, click the start-stop button to start running.
UV mode
Do not let pets into the drying box after the sterilization mode is turned on.
- Click the UV button to switch to sterilization mode;
- After the setting is completed, click the Start/Pause button to start running.
Lighting operation
In the startup state, press the light button@ to open or close; When the light
is on, press the light button @)for a long time to adjust the brightness.
Shut down
In the startup state, press the power button © for 3 seconds to shut down.
Product information
Model Number:MH66 | Space capacity: 66L |
---|---|
Working environment: 25-35°C | Material: ABS PC |
Rated input power: 1600W | Timing range: 1-120min |
Noise (pet nest):35-55dB(a) | CMIIT ID: 2020DP6462 |
* The above
dimensions are measured manually.
Please understand the slight error
Troubleshooting table
Fault description | Checking flow/Solution |
---|---|
Unable to boot | whether the power switch is turned on. |
Unable to reach the set temperature | Whether the door is closed and the |
ambient temperature is too low (recommended indoor temperature 25-35°C)
Poor drying effect| The air volume and temperature are set too low.
Error code El: Hightemperature anomaly| Turn off the power supply of the
equipment and reboot it after 10 seconds.
Error code E2:
Abnormal communication oftemperature andhumidity sensor| Turn off the power
supply of the equipment and reboot it after 10 seconds.
Error code E3: NTC data exception| Turn off the power supply of the equipment
and reboot it after 10 seconds.
Error code E4:
Abnormal fan speed feedback| Turn off the power supply of the equipment and
reboot it after 10 seconds.
Error code E5: , PTC heating anomaly| Turn off the power supply of the
equipment and reboot it after 10 seconds.
Guide after sale
Dear users, thank you for using DMDPET Dimidou products. Please read the following terms carefully before using this product:
- Warranty regulations: This product is guaranteed for one year (subject to valid purchase certificate). During the warranty period, the company will provide free maintenance services for the quality problems of the products themselves.
- Non-warranty regulations The following conditions (but not limited to the following) are not covered by the warranty:
- Damage caused by improper handling, use, storage and maintenance by users, or artificial damage.
- Repair by the maintenance department not designated by our company, or assembly, disassembly and maintenance by users themselves.
- Product accessories (such as plastic cups, etc.) and printed matter (such as instructions, etc.).
- Use gifts and accessories that are not standard for our products, causing damage.
- The model contained in the invoice is inconsistent with the model of the repaired product or has been altered.
- The warranty period is exceeded.
- Products for non-household use (such as business, commercial and corporate collective). 8 There is no valid invoice. Damage caused by force majeure. Do not belong to the scope of warranty products, will provide fee-based maintenance services, our customer service center is still enthusiastic for you.
After-sales warranty card
User name | Contact number |
---|---|
User address | |
Product model | Date of purchase |
Purchasing channel Problem record |
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. lf this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved
by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1)This device may not cause harmful
interference, and (2)this device must accept any interference received,
including interference that may cause undesired operation.
Tel: 400-0755-269 Zip Code: 518131
Shenzhen Dimidou Technology Co., LTD.
Address: 11B Haining Plaza, Dalang Street, Longhua District, Shenzhen
Copyright © Shenzhen Dimidou Technology Co., LTD. 2022. All rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>