NOAM Audio System Bluetooth Owner’s Manual
- June 7, 2024
- NOAM
Table of Contents
NUTV4
QUAD
4 Channel Marine 4″ UTV/ATV/BOAT
Audio System with Bluetooth®
OWNER’S MANUAL
warning:
This product can potentially expose you to chemicals including lead, nickel,
and chromium which are known to the State of California to cause cancer and
birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov
Thank you for making 
your choice for marine audio entertainment! Its
compact, Marine design provides flexible mounting possibilities and makes it
simple to expand the audio system capabilities of your vehicle.
NUTV4QUAD
4 Channel Marine 4″ UTV/ATV/BOAT Audio System with Bluetooth®
Two Pair 4″ 2-Way Marine Speaker:
• 4″ High-Quality Poly Injection Cone
• Butyl Rubber Surround
• Shiny Black Plastic Enclosure
• Fits 1.5″-2″ Bars
• 1″ High-Temperature KEISV Voice Coil
• 1″ PEI Neodymium Dome Tweeter
• 100 Watts
• Frequency Response: 100-20KHz
• Impedance: 4 Ohms
4 Channel Marine Power Amplifier
• 4 x 100 Watts at 4 Ohms
• Anti-Thump Turn-On
• Soft Turn On/Off
• Bluetooth”° Streaming
• AUX Input
• Volume Gain Remote Control
• T.H.D: <0.05%
• S/N Ratio: >95dB
• Channel Separation: >65dB
• Frequency Response: 10Hz- 30kHz
• Fuse : 11xx 20A
• Bluetooth® 3.0 Technology
• Bluetooth® Auto Connected While Power on
• Bluetooth® Auto Disconnected While Aux-in (3.5mm Connector)
• Easy and Quick Installed Handle-bar Mount Bracket is Included
• Bluetooth® Console Dimension: 2.12″(W) x 1.16″(H) x 3.83″(L)
• Amplifier Dimensions: 6.3″L x 3.67″W x 2.11 “H
What is included?
When first unpacking your new amplified Marine speaker system, Please check
first that the package contains all of the items below. If something is
missing, contact the store where you purchased the product.
NUTV4 QUAD
• Two Pair4″ 2 Way Marine Speaker
• One Piece 4 Channel Marine Power Amplifier
• One Piece Bluetooth°controller
Installation precautions
Before you drill or cut any holes, investigate your vehicle’s layout very carefully. Take special care when you work near the gas tank, fuel lines, hydraulic lines and electrical wiring. Never operate the amplifier when it is unmounted. Attach all audio system components securely within the amplifier to prevent damage, especially in an accident. Do not mount this amplifier so that wire connections are unprotected. in a pinched condition, in contact with any metal surfaces in your vehicle, or likely to be damaged by nearby objects. Before making or breaking power connections in your system, disconnect the vehicle battery. Confirm that your head unit or other equipment is turned off while connecting the input jacks and speaker terminals. If you need to replace the power fuse, replace it only with a fuse identical to that supplied with the amplifier, Using a fuse of a different type or rating may result in damage to your audio system or your amplifier which is not covered by the manufacturer’s warranty.
SPEAKER INSTALLATION INSTRUCTIONS:
Please note: The below instructions refers to most common bar sizes; 1.5″,
1.75″ and 2″
but using the supplied rubber pads will allow you to mount these speakers on
any bar size measured between 1.5″ and 2″
YOU’LL NEED: H5 ALLEN WRENCH
Remove the two screws from the bracket to separate the Speaker pod and the
bracket.
YOU’LL
NEED:
3″ (76 mm) pads.
Remove the backing off the pad and place it in the inner side of both the pod
and the mounting bracket.
YOU’LL
NEED:
6″ (150 mm) pads.Remove the backing off the pad and wrap it around the bar.
The pad should go all the way around the bar. if the pad is too long, cut the
extra length. the glue on the pad is there only to make installation easier.
Holding the speakers is not its purpose!
Screw the clamp to the pod and you should be good to GO!!! Use the 1.5″ pad if more padding is required.
NOTE
Rubber Pad in 3 Specification| Rubber Pad Quantity You’ll Need for Each
Mounting
Dimension:
---|---
Pad No.1: 76X30X2mm 8PCS
Pad No.2: 150x30x3mm12PCS
Pad No.3: 38x30x3mm8PCS| 2″ Bar: Pad No.1 2PCS
1. 75″ Bar: Pad No.1 2PCS and Pad No. 21PC
1.5″ Bar: Pad No.12PCS and Pad No. 2*2PCS
Attention : Pad No.2 (6-150mm) should go all the way around the bar if
the pad is too long, cut the extra length.
Note: pad No.3 is an extra small pad that can be used in case you need an
extra spacer for a better grip
Power and Speaker Wiring
wire
color – Description
Red- Battery ( + ), 12dc / 12vdc = ON
Black- Battery(-), Ground
White- CH1 (+)
White/Black- CH1 (+)
Gray- CH1 (+)
Gray/Black- CH1 (+)
Green- CH1 (+)
Green/Black- CH1 (+)
Purple- CH1 (+)
Purple/Black-CH1 (+)
Bluetooth® Pairing and Connection:
1. Connect Bluetooth® controller box to your device
2. Press and Hold % for three seconds until power indicator lights (red)
3. The system will automatically go into pairing mode The power indicator
will turn red for about 4-6 seconds and then alternating red and blue
(Bluetooth® blue Power red) Please be sure that Bluetooth®is turned ON.
Select NOAM Audio on your device to connect Bluetooth®controller (if the
Bluetooth® controller is connected the light will turn blue and not flash)
4. When the device is out of Bluetooth®range, Bluetooth® will be disconnected
automatically and automatically reconnect when detected in range again. (If
not please just repeat steps 2 and 3)
5. When Bluetooth” is disconnected or the 3.5mm AUX Input is plugged in, the
power indicator will glow red.
Playing Music:
1. Press and hold for three seconds to turn On/OFF
2. Press shortly in order to control the red background light
3. Press to start or pause the music
4. Press shortly for the next track
5. Press shortly for the Previous track
6. Press shortly for volume up
7. Press shortly for volume down
Bluetooth® Installation (MODE 1″Surface mount”)
1. Install “Z” shaped bracket threaded n to the Bluetooth® controller hook.
(packed with Bluetooth®controller.) Use the hole on the other bracket’s end to
mount the controller. any screw/bolt and a washer will allow a clean and easy
surface mounting.
2. Slide
the Bluetooth®controller into the hook
3. Press
down the Bluetooth®controller hook and then slide out the Bluetooth®
controller box at the same time to remove the Bl uetooth® controller
Bluetooth® Installation (MODE 2″Push-Fixed in Mount”)
Step 1: Decide the place for Bluetooth®remote installation. Draw and cut the
size into 85 x49mm ( LxW)
Step 2 : Push in the Bluetooth” remote
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>