UniFi 1080p Indoor Outdoor IP Camera Infrared Optical Zoom User Guide

: June 7, 2024
: Unifi

Table of Contents

UniFi 1080p Indoor Outdoor IP Camera Infrared Optical Zoom
Installation Requirements
Hardware Overview
- Ethernet Port
- Reset Button
Hardware Installation Wall/Ceiling Mount
Pole Mount
Connecting Power
Setting Up UniFi Protect via App
Adjusting the Camera View
Specifications
Safety Notices
- Electrical Safety Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

UniFi 1080p Indoor Outdoor IP Camera Infrared Optical Zoom

Installation Requirements

Pole-mounting: Two metal straps / hose clamps (not included)
Shielded Category 5 (or above) cabling with drain wire should be used for all outdoor wired Ethernet connections and should be grounded through the AC ground of the PoE. We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For more details, visit ui.com/toughcable
Surge protection should be used for all outdoor installations. We recommend that you use two Ethernet Surge Protectors, model ETH-SP, one near the camera and the other at the entry point to the building. The ETH-SP will absorb power surges and safely discharge them into the ground

Hardware Overview

Ethernet Port

10/100 RJ45 port connects to an 802.3af/802.3at or 24V Passive PoE switch for PoE power and data.

Reset Button

To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the camera is powered on.

Hardware Installation Wall/Ceiling Mount

Pole Mount

Connecting Power

The UVC G3 Pro supports 802.3af, 802.3at, and 24V Passive PoE and can be powered by any 802.3af/802.3at or 24V Passive PoE compliant switch, such as a UniFi PoE Switch. Connect the Ethernet cable from the camera directly to a PoE port on the switch.

Setting Up UniFi Protect via App

Download and install the UniFi Protect app to configure the UVC-G3-PRO.

Launch the UniFi Protect app and follow the on-screen instructions to complete setup.

Adjusting the Camera View

Specifications

UVC-G3-PRO
Dimensions (Without Mounting Plate) Ø 86 x 153 mm (Ø 3.39 x 6.02″)
Weight (Without Mounting Plate) 700 g (1.54 lb)
Enclosure UV Stabilized Polycarbonate and Die-Cast Aluminum
Networking Interface (1) 10/100 Ethernet Port
Sensor Sony IMX290, 1/2.8″
Lens 3-9 mm, f/1.2-f/2.1 Powered Zoom Lens
Field of View
Wide 108° (H), 58° (V), 125° (D)
Tele 37° (H), 20° (V), 43° (D)
Night Mode IR LEDs with Mechanical IR Cut Filter
Video Compression H.264
Resolution 1080p Full HD (1920 x 1080)
Maximum Frame Rate 30 FPS
Image Settings Flip, Brightness, Contrast, WDR, Hue, Infrared, Sharpness, Saturation, Denoise, 50/60 Hz Flicker Reduction
Management Interface
Managed Mode UniFi Protect
Standalone Mode Camera Integrated Web UI
Microphone Yes
Max. Power Consumption 12.5W
Power Method IEEE 802.3af/at Type 2 PoE or 24V Passive PoE
Power Supply 802.3af/802.3at or 24V Passive PoE Switch
Buttons Factory Reset Button
Mounting Wall/Ceiling (Kits Included) Pole (Bracket Included)
Operating Temperature -20 to 50° C -4 to 122° F
Operating Humidity 0 to 90% Noncondensing
Weatherproofing IP67

Safety Notices

Read, follow, and keep these instructions.
Heed all warnings.
Only use attachments/accessories specified by the manufacturer.

WARNING: Hot surface. Do not touch.
WARNING: Do not use this product in location that can be submerged by water.
WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning

Electrical Safety Information

Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed.
There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician