Whynter 24 inch Built-In 140 Can Undercounter Stainless Steel Instruction Manual

: June 7, 2024
: Whynter

Whynter

24 inch Built-In 140 Can Undercounter Stainless Steel
Instruction Manual

Model # : BBR-148SB

Whynter BBR-148SB 24 inch Built-In 140 Can Undercounter Stainless Steel Beverage Refrigerator with Reversible Door, Digital Control, Lock and Carbon Filter

Whynter BBR-148SB

Safety Precautions

APPLIANCE SAFETY

Your safety and the safety of others are very important to us.
To reduce the risk of fire, electrical shock, or injury when using your appliance, follow these basic precautions:

IMPORTANT SAFETY GUIDELINE

Before the appliance is used, it must be properly positioned and installed as described in this manual, please read the manual carefully. To reduce the risk of fire, electrical shock or injury when using the appliance, follow basic precaution, including the following:

DANGER

Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and do not
use an extension cord.
Do not use if the power supply cord is damaged. If damaged, it must be replaced by a qualified electrician.
It is recommended that a separate circuit, serving only your appliance be provided. Use receptacles that
cannot be turned off by a switch or pull chain.
Never clean appliance parts with flammable fluids or harsh chemicals. These fumes can create a fire hazard or
explosion.
Do not store flammable materials or liquids near the appliance.
Before proceeding with cleaning and maintenance operations, make sure to unplug the appliance.
Do not connect or disconnect the electric plug with wet hands.

Safety Precautions

Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in this manual. All other servicing should be referred to a qualified technician.
This appliance is CFC- and HFC-free and contains small quantities of Isobutane (R600a) which is environmentally friendly, but flammable. It does not damage the ozone layer, nor does it increase the greenhouse effect. Care must be taken during transportation and setting up of the appliance that no parts of the cooling system are damaged. Leaking coolant can ignite and may damage the eyes.

In the event of leakage:

Avoid open flames and anything which creates a spark
Disconnect from the mains
Air the room in which the appliance is located for several minutes and contact the Service Department for
advice

WARNING

FOLLOW WARNING CALL OUTS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL

Use two or more people to move and install the appliance. Failure to do so can result in injury.
To ensure proper ventilation for your appliance, the front of the appliance must be completely unobstructed.
Choose a well-ventilated area with temperatures above 60°F (16°C) and below 90°F (32°C).
This appliance must be installed in an area protected from the element, such as wind, rain, water spray or drips.
The appliance should not be located next to ovens, grills or other sources of high heat.
The appliance must be installed with all electrical connections in accordance with state and local codes.
The fuse (or circuit breaker) size should be 15 amperes.
It is important for the appliance to be leveled in order to work properly. For a stable installation, make sure the appliance is placed on a flat, level and solid surface.
Ensure that the surface on which the appliance is placed is strong enough to hold the appliance and the items
stored inside.
Do not use solvent-based cleaning agents of abrasives on the interior. These cleaners may damage or discolor the interior.
Keep fingers out of the “pinch point” areas. Clearance between the door and cabinet are relatively small. Be
careful closing the door when children are in the area.
This beverage refrigerator is designed to store beverage cans and bottles. If food is stored inside, ensure that
there is sufficient airflow between items. Please note that the temperature range for this beverage refrigerator is optimized for beverage storage. Perishable food items may require a different storage environment and is not recommended.
Do not place hot food or beverages into the appliance.
Close the beverage refrigerator door immediately after placing items inside to keep the internal temperature
relatively constant.
Avoid placing any objects on top of the appliance.
This is an electrical appliance, to avoid injury from electrical shock do not operate the unit with wet hands, while standing on a wet surface or while standing in water. Do not use outdoors or in wet conditions.
When positioning or moving the appliance, ensure that it is not turned upside down or unleveled greater than
45°. If the appliance does not remain in an upright position, allow it to sit upright for a minimum of 4 hours to allow the refrigerant to settle.
Never pull the power cord to disconnect it from the outlet. Grasp the plug and pull it from the outlet.
Never lift, carry or drag the appliance by the power cord.
This appliance is designed for household, non-commercial use only. Any other use will void the warranty.
Do not plug into the power outlet before set up is completed.
Do not move this appliance without emptying it and securing the door in a closed position.

Parts

Product Features

The Whynter BBR-148SB Beverage Refrigerator is a sophisticated addition to any home and perfect for cooling and storing your favorite beers and canned beverages. With its reversible and elegant full glass door, this beverage
refrigerator blend well and accent any décor.

Built-In Installation Ready
Its standard counter height makes it ideal for in-cabinet installation and is a favorite to replace that old trash compactor space. The front-venting design allows you to install this beverage refrigerator under a kitchen counter or cabinet for a seamless appearance.

Digital Temperature Control and Soft Internal Lighting
Effortlessly control the LED light and temperature settings of your beverage refrigerator using the digital control panel.

While the see-through tempered double pane glass door displays your beverage collection, this unit is also
equipped with an interior light that makes it easy to find exactly what you’re looking for.

Balanced Cooling and Auto Defrost
Features fan-forced circulation to maintain an evenly-cooled space ensuring consistent temperatures throughout the interior for more effective and efficient operation. The auto defrost feature also allows for maintenance-free continuous operation (we still recommend powering the unit off during extended periods of non-usage).

Reversible Door with Lock
This beverage refrigerator has the capability of the door opening from either the left or right side, if you prefer a
certain direction or would like the unit to follow the flow of your kitchen design. The cylinder door lock provides
protection and additional security from unauthorized access to your beverage refrigerator.

FEATURES

Capacity: 140 standard 12 oz. can
Built-in/Freestanding installation
Stainless trimmed glass door with sleek black cabinet
Touch screen control with temperature range from 34°F – 54°F
Environment friendly refrigerant
Activated carbon filter eliminates odors
Double tempered glass panel
Reversible door orientation
Soft interior LED lighting with on/off switch
Equipped with activated carbon filter ensures optimum air quality and eliminates odors
Internal fan-forced circulation for even temperature distribution throughout the cabinet
Cylinder lock and two keys
Fahrenheit and Celsius degree temperature indicators
Three big chrome-plated flat shelves with black plastic plate front end .

TECHNICAL DATA

Installation

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electrical shock, or injury when using your appliance, follow these basic precautions:

Read all instructions before using the appliance.
DANGER or WARNING: An empty beverage refrigerator can be a hazardous for children or small pets. If
disposing of the beverage refrigerator, remove gasket seals, latches, lids or the entire door from your unused
appliance, or take other action to ensure the beverage refrigerator is harmless.
Never allow children to operate, play with, or crawl inside the appliance.
Never clean appliance parts with flammable fluids or harsh chemicals. The fumes can create a fire hazard or explosion.
Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or any other appliance.
The fumes can create a fire hazard or explosion.

INSTALLATION INSTRUCTIONS

BEFORE USING YOUR APPLIANCE

Remove the exterior and interior packing.
Before connecting the appliance to the power source, let it stand upright for approximately 4 hours. This will
reduce the possibility of a malfunction in the cooling system from handling during transportation.
Clean the interior surface with lukewarm water using a soft cloth.
Install the handle on the door.

INSTALLATION OF YOUR APPLIANCE

The appliance is designed for built-in, recessed or free standing installation.
WARNING: Do not store or install the appliance outdoors.
CAUTION: This beverage refrigerator is designed for storing and cooling beverages. Do not store perishable food, medicine or other medical products.
Place your appliance on a hard and level floor that is strong enough to support it when it is fully loaded.
We do not recommend installing the appliance on carpet.
To level your appliance, adjust the leveling legs at the bottom of the appliance if needed.
For free standing installation, 5 inches (127mm) of space between the back and sides of the appliance is suggested, which allows the proper air circulation to cool the compressor and condenser. Even for built-in installation, a ¼” (6.35mm) space is required on each side and at the top. The front air vent must never be covered or blocked in any way.
NOTE: DO NOT install the appliance near an oven or other heating source. Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption. For best performance, do not install the appliance behind a cabinet door or block the base grille.
Avoid locating the appliance in area that may be exposed to excessive moisture.
Plug in the appliance into an exclusive, grounded wall power outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a qualified electrician or contact Whynter Customer Support.

Installation

BUILT-IN CABINET INSTRUCTIONS
These appliances are designed for both built-in or free standing installation. For built-in installation, ensure
proper service access and ventilation, allow at least ¼” space on each side and at the top.

Installation

ELECTRICAL CONNECTION

WARNING: Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is
damaged, have it replaced by a qualified electrician or contact Whynter Service Department

This appliance requires a standard 115/120 Volt AC ~/60Hz electrical ground outlet with three-prong. Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded. The cord should be secured behind the appliance and not left exposed or dangling to prevent accidental injury.

The appliance should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating label on the appliance. This provides the best performance and also prevents over-loading the house wiring circuit that could cause a fire hazard from overheating. Never unplug the appliance by pulling the power cord. Always grip the plug firmly and pull straight out from the receptacle. Repair or replace the power cord immediately if it becomes frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. When moving the appliance, be careful not to damage the power cord.

EXTENSION CORD

Because of potential safety hazards, it is strongly recommended that you do not use an extension cord with this
appliance. However, if you must use an extension cord, it is absolutely necessary that it be a UL/CUL-Listed, 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 115 volts and at least 10 amperes.

INSTALLING STAINLESS STEEL HANDLE

This appliance includes stainless steel handle that are not required to operate this appliance. To install the handle please follow the below instructions:

STAINLESS STEEL HANDLE

The gaskets are easily displaced by hand, no tools are necessary.
Use a flat-head screwdriver to remove the two pre-installed decorative plugs from the back of doors. Some beverage refrigerators have no decorative plugs.
Install the handle tightly as shown with two screws, lock washers and flat washers provided. (DO NOT over tighten as this will cause damage to the handle and stainless steel door frame).
Replace the door gaskets to its original position.

REVERSING THE DOOR SWING OF YOUR BEVERAGE REFRIGERATOR

Note: All parts removed must be saved for proper reinstallation of the door.

This appliance has the capability of the door opening from either the left or right side. The appliance is delivered
to you with the door opening from the left side. Should you desire to reverse the opening direction, please follow
the following reversal instructions.

Remove the front ventilation grille (2) and the adjustable ventilation grille (1) by unscrewing the screws
(3) & (4). (Figure 1)
Remove the bottom hinge plate (5) by unscrewing the four lock screws (6). Be careful to hold the glass door
firmly after removing the screws. (Figure 2)
Gently pull down to remove the glass door from the right top hinge and place it on a padded surface to avoid
the risk of damage, then remove the right top hinge (7). (Figures 3 & 4)
Unscrew and transfer the hinge pin of the bottom hinge plate (5) to the opposite side.
Pop out the cover caps on the upper left side corner of the inside cabinet and use them to cover the screw holes on the right hand side.
Screw the alternative left top hinge (9), included in the fittings, on the left hand side of cabinet. (Figure 4)
Relocate the door to the designated position. Then screw the bottom hinge assembly on the left designated
position and tighten it after the door is leveled. (Figure 2)
Reassemble the ventilation grilles.

Whynter Diagram

Operation and Controls

It is recommended you install the appliance in a place where the ambient temperature is between 72º- 78ºF /
23º-26ºC. If the ambient temperature is above or below recommended temperatures, the performance of the
beverage refrigerator may be affected. For example, placing your appliance in extreme cold or hot conditions may
cause interior temperatures to fluctuate.

NOTE:

When using the beverage refrigerator for the first time or restarting after being shut off for a long period of time, there may be a few degree variance between the set temperature and the LED readout. This is normal due the length of activation time. The unit should return to normal after running for a few hours. This unit will not raise its internal temperature if the ambient temperature where the unit is located is lower than the set temperature.

CONTROL PANEL GUIDE

ºF/ºC SELECTOR

Select the temperature display setting in Fahrenheit or Celsius degree. To change the temperature from Fahrenheit
to Celsius or from Celsius to Fahrenheit, press and hold the LIGHT key for 5 seconds.

NOTE: If the appliance is unplugged, encounter power interruption, or turned off, you must wait 3 -5 minutes before restarting the appliance. If attempted to restart before this time delay, the appliance may not start.

SETTING THE TEMPERATURE CONTROL

During normal operation, the temperature display on the control panel shows the temperature inside the
appliance.
When the unit is plugged in for the first time, the unit will power up automatically to the preset defaults. The
preset temperature is 40ºF (4ºC).
You can press the UP and DOWN keys to control the internal temperature of the appliance.
The temperature that you desire to set will increase 1ºC or 1ºF if you press the UP key once and will decrease
1ºC or 1ºF if you press the DOWN key once. The display flashes while you make the setting.
After the temperature has been set, the display will flash four times before it shows the current internal
temperature of the particular temperature zone.
To view the set temperature at any time, press the UP or DOWN key, the set temperature will temporarily flash in the display for 5 seconds. Then the display shows the current internal temperature again.

TEMPERATURE MEMORY FUNCTION
In the event of a power interruption (power surge, breaker switch, etc.), the unit can remember the previous temperature settings. When the power has restored, the temperature display will show the current cabinet temperature.

INTERIOR LIGHT
The interior light makes it easy to view your beverage labels and enhances the display of your collection. The light can be turned on or off pressing the light button on the display.

CABINET SHELVES
NOTE: Do not cover any part of the shelves with aluminum foil or any other material that will prevent adequate air circulation within the cabinet.
This appliance is equipped with removable shelves. To prevent damage to the door gasket, make sure the door is
opened completely before pulling the shelves out.

ACTIVATED CARBON FILTER
The Whynter BBR-148SB is equipped with one activated carbon filter, which ensures optimum air quality within the beverage cabinet. This filter counters and prevents any contaminants and odors from the ambient air affecting the taste of the beverage stored.

Replace the active carbon filter once a year. If you are interested in purchasing an additional carbon filter, please
contact support@whynter.com for retail sales information.

To change the filter,

Turn the filter cover 90° clockwise or counterclockwise and then remove the filter.
Insert the new filter in the vertical position.
Turn the filter cover 90° clockwise or counterclockwise until it click into position.

NORMAL SOUNDS
The unit is cooled by a compressor. The compressor pumps coolant through the cooling system, producing operating noise.

Even when the compressor cuts out, noises caused by changes in temperature and pressure are unavoidable. Operating noise will be most audible immediately after the compressor comes on. It becomes quieter as the operating period continues.

The following noises are normal and occur from time to time:

Gurgling sound, caused by the refrigerant flowing through the appliance’s coils,
Humming noise made by the compressor. This noise can get louder for brief periods when the motor is switching on.
Cracking/popping sounds, resulting from the materials contraction and expansion due to temperature variations,
Fan operating sound, to circulate the air within the beverage cabinet.
Unusual noise is normally the result of improper installation.
Where the unit is installed in open-plan kitchen or in partition walls, the level of operating noise will be heard more acutely. However, this is due to the surrounding architecture and not to the unit.
NOTE: An individual’s perception of noise is directly linked to the environment in which the unit is located, as well the specific type of models. Our appliances are in line with international standards for such appliance and in line with the latest technical developments. Please remember that the noise of the compressor and the coolant circulating in the system is unavoidable.

Storage

BBR-148SB
Top Shelf : 42 cans
Mid Shelf : 42 cans
Lower Shelf : 42 cans
Bottom : 14 cans
42 + 42 + 42 + 14 = 140 cans

Care and Maintenance

CLEANING YOUR APPLIANCE

Turn off the power, unplug the appliance, and remove all contents from the appliance and store them in a suitable place.
Clean the inside, the door seal and the inside of the glass with a clean, damp cloth.
Never use detergents or other substances that emit odors.
Always keep the door closed when cleaning the outside of the appliance. Make sure no detergent odors penetrate into the appliance.
Clean the side panels and door surfaces with a clean and soft cloth. If necessary, use a moist cloth. Alternatively, use a microfiber cloth.
The humidity tray should be hand-washed with water and detergent. After cleaning, always make sure the tray is thoroughly rinsed with clean water before replacing.

PREMISES POWER FAILURE

In the event of a power interruption, temperature settings automatically defaults to factory settings once power is restored.
Factory default temperature setting is 40°F. To set a different desired temperature, refer to the “SETTING THE TEMPERATURE” and “°C and °F SELECTOR” section on page 10.
Most power failures are corrected within a few hours and should not affect the temperature of your appliance if you minimize the number of times the door is opened. If the power is going to be off for a longer period of time, you need to take the proper steps to protect your contents.

VACATION TIME

Short vacations: Leave the appliance operating during vacations of less than two days.
Long vacations: If the appliance will not be used for an extended period, remove all items and turn off the appliance. Clean and dry the interior thoroughly.

MOVING YOUR APPLIANCE

Remove all items inside the appliance.
Securely tape down ( we recommend using painter’s tape ) all loose items ( shelves ) inside your appliance.
Turn the adjustable legs up to the base to avoid damage.
Tape ( we recommend using painter’s tape ) the door shut.
Be sure the appliance stays secure in the upright position during transportation and protect the exterior of appliance with a blanket, or similar item.

PREPARING FOR STORAGE

If the beverage refrigerator will not be used for a long time, or is to be moved to another place, it will be necessary to defrost the unit and dry the interior.

Disconnect the beverage refrigerator from the power supply by removing the power plug from the wall socket.
Leave the door open to allow for air circulation and to prevent mold, mildew and unpleasant smells.

CAUTION: Store the unit out of the reach of children. If you have children, you may want to take additional
precautions such as removing the door to prevent a child from being trapped inside the beverage refrigerator.

NOTE:

If the beverage refrigerator is unplugged, encounter power lost, or turned off; you must wait 3 to 5 minutes before restarting the beverage refrigerator.
When the beverage refrigerator is used for the first time or restarted after having been shut off for a long time, there could be a few degrees variance between the temperature you select and the one indicated on the display. This is normal and it is due to the length of the inactivation time.
The appliance should be located in the coolest area of the room, away from heat producing appliances, and out of any direct sunlight.
Ensure that the appliance is adequately ventilated. Never obstruct the air vents.
Close the door tightly and do not open the appliance too frequently or for a long period of time.
Store the content in an organized way.
Do not over load the appliance to allow air to circulate.

Troubleshooting

ONE YEAR LIMITED WARRANTY

This WHYNTER Beverage Refrigerator is warranted, to the original owner within the 48 continental states, for one year from the date of purchase against defects in material and workmanship under normal use and service. When making a warranty claim, please have the original bill or invoice of purchase with purchase date available. Should your WHYNTER Beverage Refrigerator prove defective within one year from the date of purchase, return the defective part or unit, freight prepaid (within two months of purchase; after two months to one year, customer will be responsible for freight cost to Whynter’s service department), along with an explanation of the claim to Whynter LLC. A return authorization number issued by Whynter is required for all warranty claims and returns. Please package the WHYNTER Beverage Refrigerator carefully in its original packaging material to avoid damage in transit. The original box and packaging material should be retained, as Whynter is not responsible for the cost of replacement packaging. Under this warranty, Whynter will repair or replace any parts found defective at our discretion. This warranty is not transferable. After the expiration of the warranty, the cost of labor and parts will be the responsibility of the original owner of the unit.

THIS WARRANTY DOES NOT COVER:

Acts of God, such as fire, flood, hurricanes, earthquakes and tornadoes.
Improper power supply such as power surge, low voltage, defective household wiring or inadequate fuses.
Use in commercial or industrial applications.
Damage, accidental or otherwise, to the WHYNTER Beverage Refrigerator while in the possession of a consumer not caused by a defect in material or workmanship
Damage caused by consumer misuse, tampering, or failure to follow the care and special handling provisions in the instructions.
Damage to the finish of the case, or other appearance parts caused by wear.
Damage caused by repairs or alterations to the product by anyone other than authorized by the manufacturer.
Removal, Replacement Packaging, Freight and Insurance cost for the warranty service.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS PRO-VIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTA-BILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PE-RIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. WHYNTER SHALL NOT BE LIABLE FOR CON-SEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT AL-LOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRIT-TEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.

Please retain the original proof of purchase in order to obtain warranty services.
Warranty begins from the original date of purchase.
To obtain service or information, contact
Whynter LLC via email at support@whynter.com or call
866-WHYNTER.
Product contents and specifications may change without notice.
Copyright © 2021 Whynter LLC
WWW.WHYNTER.COM