Pyramind 3D Printer Installation Guide

Quick Installation
Guide

Safety Instructions

When printer is working, please beware of the high temperature of hotbed, extruder head, and other hot parts, Please don’t touch any hot part during printing in case of scald. Please note hot parts need time to coo! down after working.

The printer has 220V AC/MOV AC voltage and other high voltage power connector, Please 5 don’t touch conductive part in case of electric shock,

The power of some key parts of the printer (such as hotbed, extruder head) is stronger, During installation and usage, please ensure all terminals are connected tightly to avoid any (sparking may be caused by loose wiring. To ensure safety, printer should be manned during working.

The printer betongs to mechanical equipment. When it is working, please don’t touch ‘Se moving parts in case of mechanical wounding.

Machine parameters

Repetier-Host ect

| Power Supply| AC :115-240 V

DC:24V 15A

Nozzle Number| 1| Total Power| 360W
Slice Thickness| 0.1-0.4mm| Bed  Temp| ≤ 110℃
Precision| ±0.1mm| Nozzle Temp| ≤ 260℃
Nozzle Diameter| 0.4mm.Support

0.2/0.3/0.6/0.8mm

| Printing Speed| ≤180mm/s,

Normal 30-60mm/s

Structure introduction

block2
3. Z-motor 2| 9. X belt bearing1| 15. M5×25 8
4. Coupling 2| 10. Belt 1| 16. Screw rod 2
5. M4×20 4| 11. Extruder part 1| 17. 2020 aluminum profile2
6. M4×16 6| 12. X end stop1|

Preparation list

Part 1 : Install the Z parts

Preparation list

Part 2: Install the X parts

Part 3: Fixed gantry

Part 4: Installing screw rod

Part 5: Install support rod

Part 6: Line connection

Select voltage before starting up

Level the heated bed

1. Auto Home All Disable xy
   

2. Test with A4 paper, adjust the nuts under the platform up and down, to make the nozzle just presses the A4 paper, and ensure that the four corners are the same distance. Repeat steps 1-2 times if necessary
   

The normal distance

Too close: The short distance may lead to abnormal discharge or even damage caused by plugging the nozzle
Normal: The correct distance will help you to complete the printing work better and more economically
Too far: Too far distance will cause printing materials to be unable to attach to the hot bed, so that they cannot be printed normally

Installation software

1. Open the SD card,find the CURA(or download online), After installing the software:Add a printer Settings
   

2. Import the profile from the SD card
   

Start printing

1. Open the Cura : File —–Open file(Import your STL)—- Slice
   

2. Save file to the TF card
   

3. Put the TF card to the printer, Select “Printing”—-Select your file
   

4. Select “Confirm”, than start printing after heating
   

Warm reminder

Dear customers:

1. In order to ensure the quality of products, we will carry out printing test for each printer in the factory. If you find that the nozzle has slight traces of use, this is left by the printing test. We try to clean it up as much as possible, but please don’t mind.
2. The factory test voltage is 220V. When installing, please select 110V or 220V according to your local power supply to ensure the printer can work normally. Please find the following power supply identification, and use a screwdriver or tweezers to move the regulator on the power supply.

Trouble Shooting

Tips: More informations on the TF card

email: service@fasttobuy.com
Amazon: fasttobuyli@gmail.com
Amazon store: www.amazon.com/shops/toauto

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>