hama 00200016 Universal USB-C Notebook Power Supply Instruction Manual

: June 7, 2024
: Hama

Table of Contents

hama 00200016 Universal USB-C Notebook Power Supply
Operating instruction
Package contents
Safety instructions
Start-up and operation
Care and Maintenance
Read User Manual Online (PDF format)
Download This Manual (PDF format)

hama 00200016 Universal USB-C Notebook Power Supply

Operating instruction

Instructions

Package contents

Universal USB-C notebook power supply unit
USB-C 2.0 Cable 3A(max. 60W)
These operating instructions

Safety instructions

Use the product only for the intended purpose.
Do not use the product in the immediate vicinity of heaters, other heat sources or in direct sunlight.
Ensure there is sufficient scope for heat dissipation and ventilation.
Only use the article under moderate climatic conditions.
Do not use the product in areas in which electronic products are not permitted.
Do not use the product in a damp environment and avoid splashing water.
Do not short-circuit the battery of the opened terminal device. There is a risk of explosion.
Protect the product from dirt, moisture and overheating and use it in dry environments only.
Do not drop the product and do not expose it to any major shocks
Do not operate the product outside the power limits specified in the technical data.
Always pull directly on the plug when disconnecting the cable, never on the cable itself.
Make sure that cables do not pose a tripping hazard or block emergency exits.
Do not bend or crush the cable.
As with all electrical products, this device should be kept out of the reach of children.
Do not modify the device in any way. Doing so voids the warranty.
Keep the packaging material out of the reach of children due to the risk of suffocation.
Dispose of packaging material immediately in accordance with the locally applicable regulations.

Risk of electric shock

Do not open the device or continue to operate it if it becomes damaged.
Do not use the product if the AC adapter, adapter cable or power cable is damaged
Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.

Start-up and operation

Note –mains voltage 100 –240 V

The power supply unit is suitable for mains voltages of 100 –240 V and therefore can be used worldwide. Please note that a country-specific adapter may be necessary.

Ensure that your notebook requires a supply voltage of 5V /9V/12V /15V /20V (+/- 1Volt).
You can find this information on the original power supply unit or in your terminal device’s operating manual. If necessary, ask the dealer who supplied your terminal device or contact your terminal device manufacturer’s support service.
Do not use the universal notebook power supply unit if you are unable to definitively determine your terminal device’s supply voltage.
Ensure that the total power consumption does not exceed the power supply unit’s rated output capacity of 65 W.
Failure to comply with this may cause damage to the universal notebook power supply unit and the connected terminal device!

Note the instructions in your device’s operating manual. If these do not contain any instructions expressly to the contrary, proceed as follows:

Note –Power Delivery/Quick Charge

Plug &GO: no additional software required, simply plug in and start: Thanks to Power Delivery/Thunderbolt™ 3/Quick Charge, the voltage and power are adjusted automatically.
Be aware that, for efficient and optimized charging, your terminal device must support the PD (Power Delivery)/TBT3 (Thunderbolt™ 3)/QC (Quick Charge) function.
If you have a large number of PD/TBT3/QC-enabled terminal devices with different firmware updates, it may be that the function is not fully supported.+
Only operate the product from a socket that has been approved for the device. The socket must be installed close to the product and must be easily accessible.
Disconnect the product from the power supply using the On/Off switch –if this is not available, unplug the power cord from the socket.
If using a multi-socket power strip, make sure that the total power consumption of all connected devices does not exceed the power strip’s maximum throughput rating.
Connect the USB-C cable to the power supply unit and your terminal device.
Then connect the mains plug to a properly installed socket.
The terminal device can now be used and switched on /charged.
Disconnect the product from the mains after use.

Care and Maintenance

Disconnect the product from the mains before cleaning.
Only clean this product with a slightly damp, lint-free cloth and do not use aggressive cleaning agents.
Ensure that no water is able to enter the product.

Warranty Disclaimer
Hama GmbH &CoKG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.