VABSCE VB-007 Night Vision Binoculars Instructions

VABSCE VB-007 Night Vision Binoculars

Congratulations on your purchase of this high quality night vision binoculars device. Use this device to view your surroundings in low light conditions or even in complete darkness with the built-in infrared light. You can even take pictures and video using the device which can be stored on a TF card. This device can also be used to take photos and video during the day. Use the supplied A/V cable to view your images on a television or download the images to your computer using the supplied USB cable. Also includes a neck strap and handy storage pouch

Accessories

• 1x Night vision binoculars device
• 1x Mini USB cable
• 1x Power bank holder
• 1x A/V cable
• 1x Storage pouch
• 1x User manual

Over View

Parts overview

1. Ocular
2. Power button
3. IR button
4. Zoom button
5. Mode button
6. Snap button
7. USB port
8. TF card slot
9. TV out
10. Battery cover
11. Objective lens focus wheel
12. Objective lens
13. Infrared filter
14. IR Illuminator
15. Infrared zoom
16. Tripod adapted

Battery Installation

Open battery compartments and install the 8XAA batteries being sure to follow the polarity markings inside the battery compartment.
Close the battery covers. Please pay attention to the direction of covers.

Inserting / Removing the TF card

Insert the TF card into the TF card port and push until it locks in place. To remove the installed TF card, please push the TF card inward to release it. Storage capacity: 8GB or above is recommended
Note: The device will show the icon “ “if the micro SD card in not installed

Turning On the Night vision binoculars device

Power On: Press the power button still for about several seconds to start the Night vision binoculars device.

Turning Off the Night vision binoculars device

Power Off: Press the power button for about several seconds to turn off the Night vision binoculars device.

Key Button Functions

button again.
In photo capture mode: Press to take photo.
In playback mode: Press to Play or delete the video.
In Menu mode: Press to select.
【ZOOM】| In video mode: Press to zoom out.
In photo capture mode: Press to zoom out.
In playback mode: Press to select the next picture or video
In menu mode: Press to select the previous menu listing.
【IR】| In Video/Photo mode: Press to turn on the infrared light.
With each additional click, the IR brightness will increase
In playback mode: Press to select the previous photo or video.
In menu mode: Press to select the next menu listing.

Taking Photo and Video Function

Taking a photo: Press the [MODE] button and select the capture photo mode. The icon  will appear in the top left corner of the screen. It means you enter the photo function. Press the [SNAP] button to take photos.

Taking a v ide o : Press the [MODE] button and select the video mode.
The icon will appear in the top left corner of the screen. It means you enter the video function. Press the [SNAP] button to start recording video and press the [SNAP] button again to stop recording.

Watching stored videos and photos : Press the [MODE] button and select playback mode . You may then look through your saved photos/videos with the [Zoom] or [IR] buttons. [Zoom] or [IR] buttons can be used for choosing the previous page or next page.

Deleting Stored Videos and Photos : In playback mode, press the [SNAP] button to enter the menu. You will be given the options to play or to delete the image or video. While deleting the photo, you will see the menu by pressing the [SNAP] button .The first one is “Delete” .You can choose “Delete, Delete All or Exit” by [ZOOM] or [IR] . While playing or deleting the videos, you will see the menu by pressing the [SNAP] button. The first one is “Play” .You can choose “Play ,Delete, Delete All or Exit” by [ZOOM] or [IR] button .

The screen display during 【Playback】 mode

Delete Photos|
---|---
Delete Photos|
---|---

Focusing the image

Target the object you would like to view and turn the focusing wheel located just below the objective lens until the image on the screen is sharp and clear. The focusing wheel is No.11 in Parts overview picture.

Adjust infrared projection angle

You can adjust infrared projection angle from 5.2°to 10.2° by No.15 in Parts overview picture.

LCD Display Information

Your screen display in photo mode

brightness from 1 to 7)
3| Remain capacity quantity
4| Digital zoom
5| Battery power
6| Backlight from 0 to 15

Your screen display in video mode

brightness from 1 to 7)
3| Remaining time of recording
4| Digital zoom
5| Battery power
6| Backlight from 0 to 15

LCD Display Information.

Press [MODE] four times continuously and enter menu mode.
Note: [ZOOM] means “up” [IR] means “down” [SNAP] means “ok” button. After setting, you can press [MODE] again to exit the menu.

Your screen display during menu mode

Format SD|
Select to format the TF card
---|---
 | Format is an operation that initializes a partition on a disk or disk. This usually causes all files in the existing disk or partition to be erased. You can choose yes or no by [ZOOM] and [IR] . Lastly press [SNAP] to confirm.
Power Save| Power off mode :The NV can be set to automatically shut down when not operating after the selected period of time.
|
| You can choose off 5min.,15 min.,30 min or cancel. For turning the device off automatically. The buttons of selection and confirmation is the same as mentioned before. Then choose cancel to exit.
Date|
 | Find Date input function by [ZOOM] and [IR]. Press [SNAP] to confirm and start to set the date .[ZOOM] means up . [IR] means down . [SNAP] means “ok” button. After setting, you can press [MODE] again to exit.
Time|
| Find time input function by [ZOOM] and [IR]. Press [SNAP] to confirm and start to set the date .[ZOOM] means up . [IR] means down . [SNAP] means “ok” button. After setting, you can press [MODE] again to exit.
Flicker|

| You can choose 50Hz or 60Hz by [ZOOM]  and [IR] .Lastly press [SNAP] to confirm. Then choose cancel to exit.
TV Standard| The video output mode can be set to NTSC (North America) or PAL (Europe)

 | You can choose NTSC or PAL by [ZOOM] and [IR] .Lastly press [SNAP] to confirm. Then choose cancel to exit.
Language|

 | You  can choose language you need by [ZOOM] and [IR] .Lastly press [SNAP] to confirm.
LCD Backlight|
set the backlight from 0 to 15
| You can choose from level 0-15 to decide screen backlight intensity. Find Backlight  function  and  start  to  set  the  level  by  [ZOOM]  or [IR] button . [SNAP] means “ok” button. After setting, you can press[SNAP] again to exit.
Date/Time Tag|
When you choose on, the date/time will be showed in the picture or video.
 | You  can  choose Off or On you need by [ZOOM] and [IR] .Lastly press [SNAP] to confirm.
Version|
The software version of the device

Using the zoom function

This device features a zoom function that can be used while taking a video or photo.
Press the [ZOOM] button to toggle between 1X and 3X digital zoom. Optical magnification power :3.6X-10.8X. (The optical magnification is 3.6X) (3.6X-10.8X Zoom Magnification = Optical Magnification × Digital Magnification)

Using IR light in complete darkness

This device can be used in complete darkness when using the built in IR (infrared) light. Press the [IR] button to activate the infrared light. Remove the IR Lens cover and press the [IR] button to select between the 5 levels of brightness (while plugging in USB power supply the IR brightness from 1 to 7).

Note: Don’t forget to remove the IR Lens cover while using in the darkness.

Pic. 1

Pic. 2

Viewing videos and photos on TV

Connect the AV output port of the night vision binoculars device with an A/V cable. Connect the other end of the A/V cable to the TV video input.
In playback mode, press the ZOOM/IR buttons to select the file you will display on your TV.
Note: When the night vision binoculars device is connected to a TV, the screen inside the device will not work.

Transmitting stored videos and photos to a computer

Using a USB cable, you can connect the night vision binoculars device to a computer. You can find the stored photo/video files on the computer by looking under “My computer \ removable disk”.
Once the removable disk is selected, you can view, delete, move, or copy any video or photo.

Install power bank on night vision binoculars device

Care and maintenance

Clean the device only with a dry or slightly damp, lint-free cloth. Do not use abrasive cleaners to clean the device.
This device is a high-precision optical instrument, so in order to avoid damage, please avoid the following practice:

• Use the device in ultra-high or ultra-low temperature.
• Keep it or use it in moist environment for long.
• Deliver or use it in strongly shocking environment.

Note: Remove the batteries from the device if it is not used for a longer time.

VB007 Specification

Catalog| Function Description
Optical performance| Magnification    (3.6-10.8) X31
Digital Zoom Max 3x
Angle Of View     9.2°
Objective Aperture 31mm
Exit Pupil Distance 30mm
F# for Objective lens    1.3
IR ZOOM    2X
2m~∞ in daytime; Viewing in the darkness up to 300M (monochrome)
Imager| High-sensitivity CMOS Sensor
Size    1/2.7”
Resolution    1920X1080
Displayer| Backlight 0-15 grades adjustment
OSD menu display
CVBS always output with VGA resolution
IR LED| 5W Infrared 850nm LED
TF Card| Support SDHC 8GB~128GB TF Card
Operation| Preview
Record JPEG file in TF storage
Capture mp4 file in TF storage
Playback media file from SD storage
Power| External power supply – DC 5V/2A
8 pcs AA battery      8-12 V
Low battery warning

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>