KYMETA u8 Go Terminal User Guide

June 6, 2024
KYMETA

KYMETA logo
QUICKSTART GUIDE
ELEVATED, LATCHED

KYMETA u8 Go Terminal

KICKSTAND LATCH

KYMETA u8 Go Terminal - fig1

Secure the kickstand in the latch while elevated.

REMOVE THE u8 GO FROM CASE (OPTIONAL)

KYMETA u8 Go Terminal - fig2

  1. Press the latch release bar.
  2. Lift the Kymeta™ u8 GO out of the spring latch.
  3. Push the u8 GO towards the handle and lift.

BOTTOM LATCH DETAIL

KYMETA u8 Go Terminal - fig3

Keep the u8 GO angle low for removal.
The latch won’t release if elevated beyond 30º

KICKSTAND, STOWED

KYMETA u8 Go Terminal - fig4 Remove the kickstand when mounting the u8 GO onto a vehicle.

SECURE THE KICKSTAND

KYMETA u8 Go Terminal - fig5

  1. Align the kickstand and the base arrows.
  2. Latch the kickstand in the base hooks.
  3. Secure the kickstand with the pin.

REMOVE YAKIMA MIGHTY MOUNT

KYMETA u8 Go Terminal - fig7| KYMETA u8 Go
Terminal - fig9
---|---

INSTRUCTIONS

1. Loosen the thumbscrew and remove the clamp2. Lift the lower clamp pad.
2. Loosen the socket head cap screw with the provided Allen wrench.
3. Remove the lower clamp.| 1. Align the lower clamp with the T-nut in the aluminum extrusion.
2. Thread the fastener into the T-nut and position the mighty mount on the rail per the vehicle’s crossbar spacing.
3. Install the lower clamp pad.
4. Install the upper bail. For sizing guidelines, see Sizing Process in the following cards. Refer to the manufacturer’s instructions for additional details.
---|---

SIZING PROCESS: YAKIMA MIGHTY MOUNT

KYMETA u8 Go Terminal - fig10

  1. Install the pad on the smaller bail “A” and press to secure.
    KYMETA u8 Go Terminal - fig12

  2. Attach the bail to the top slot on the clamp base.
    KYMETA u8 Go Terminal - fig14

  3. Install the mount on the crossbar with the hex bolt facing the direction of vehicle travel. Use the short bolt with the bail “A” and the long bolt with the bail “B.”
    KYMETA u8 Go Terminal - fig18

  4. The bolt must protrude 1/8 in. from the bail when installed on the crossbar. If there is not enough thread exposed, move the bail to the bottom slot from step 2.
    KYMETA u8 Go Terminal - fig20

  5. If the bottom slot doesn’t work, install the pad on the bigger bail “B” and repeat steps 2 and 3. Use the long hex bolt with the bail “B.”
    KYMETA u8 Go Terminal - fig22

  6. Attach the knurled wheel to the hex bolt and tighten until the wheel no longer turns. If the mount slides on the crossbar, repeat the sizing process.

KYMETA logo2

For Contact Kymeta customer support at support@kymetacorp.com
or call Kymeta at 1-855-525-6638 for urgent issues.
12277 134th Ct. NE, Redmond, WA 98052
Phone: 425.896.3700
www.kymetacorp.com
© 2021 Kymeta Corporation. All Rights Reserved.
KYMETA, KYMETA CONNECT, MAKING MOBILE GLOBAL, and CONNECTED BY KYMETA
are trademarks of Kymeta Corporation, with registrations or pending applications in the U.S. and/or other countries.
All other trademarks are the property of their respective owners.
Document number: 700-00119-000 rev A

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals