SENCO F-LXP Cordless Stapler Instruction Manual
- June 6, 2024
- SENCO
Table of Contents
F-LXP Cordless Stapler
F-LXP
CORDLESS STAPLER
Operating Instructions
KYOCERA-SENCO Industrial Tools, Inc. 8450 Broadwell Road Cincinnati, OH 45244 1-800-543-4596 www.senco.com
IMPORTANT: Read before use.
NFD810YENG · Issued April 30, 2021
© 2021 by KYOCERA-SENCO Industrial Tools, Inc.
Table of Contents
Symbols……………………………………………………………………………………………………………………. 3 General Power Tool
Safety Warnings……………………………………………………………………………4
Work Area Safety……………………………………………………………………………………………………..4 Electrical Safety
……………………………………………………………………………………………………….4 Personal Safety
……………………………………………………………………………………………………….4 Power Tool Use and Care
………………………………………………………………………………………….5 Battery Tool Use and Care
…………………………………………………………………………………………5 Service
…………………………………………………………………………………………………………………..6 Stapler Safety Warnings
……………………………………………………………………………………………..6 Additional Tool Safety Warnings
………………………………………………………………………………….7 Safety Warnings for Charger and
Battery………………………………………………………………………9 Functional
Description………………………………………………………………………………………………11 Tool
Operation………………………………………………………………………………………………………….12 Mode
Selection………………………………………………………………………………………………………12 Warning
Light………………………………………………………………………………………………………..14 Time-Out /
Lockout…………………………………………………………………………………………………15 Depth of Drive Adjustment
………………………………………………………………………………………15 Belt
Hook………………………………………………………………………………………………………………15 Fastener Jam
…………………………………………………………………………………………………………16 Battery Charging
………………………………………………………………………………………………………17 Battery Disposal
…………………………………………………………………………………………………….18 Maintenance
……………………………………………………………………………………………………………18 Accessories
……………………………………………………………………………………………………………..18 Fastener Specifications
…………………………………………………………………………………………….19 Technical Specifications
……………………………………………………………………………………………19 Troubleshooting
……………………………………………………………………………………………………….20
2
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
DANGER:
Indicates a hazardous situation, which, if not avoided, will result in death or serious injury.
WARNING:
Indicates a hazardous situation, which, if not avoided, could result in death or serious injury.
CAUTION:
Indicates a hazardous situation, which, if not avoided, may result in minor or moderate injury.
NOTICE:
(Without Safety Alert Symbol) indicates information considered important, but not related to a potential injury (e.g. messages relating to property damage).
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product in a better, safer manner.
SYMBOL
NAME
DESIGNATION/EXPLANATION
Safety Alert
Indicates a potential personal injury hazard.
Read Operator’s Manual
Eye Protection
To reduce the risk of injury, user must read and understand operator’s manual
before using this product.
Always wear eye protection with side shields marked to comply with ANSI Z87.1.
Do not rest your finger on the trigger when picking up the tool, moving
between operating areas and positions or walking, as resting finger on trigger
can lead to inadvertent operation. For tools with selective actuation, always
check the tool before use to ascertain the correct mode is selected.
This tool has either selective actuation for contact actuation or continuous
contact actuation by actuation mode selectors or is a contact actuation or
continuous actuation contact tool and has been marked with the symbol above.
If using this tool in selective actuation mode, always ensure it is in the
correct actuation setting.
Be careful when changing from one driving location to another.
R
Do Not Oil
Routine lubrication is not necessary.
Wet Conditions Do not expose to rain or use in damp locations. Alert
Recycle
This product uses Lithium-ion batteries. Local, state, or federal laws may prohibit disposal of batteries in ordinary trash. Consult your local waste authority for information regarding available recycling and or disposal options.
V
Volts
Voltage
Direct Current Type or characteristic of current
3
General Power Tool Safety Warnings
WARNING Read all safety warnings, instructions, illustrations and
specifications
provided with this power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool”
in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
WORK AREA SAFETY 1. Keep work area clean and well lit. Cluttered or dark areas
invite accidents. 2. Do not operate power tools in explosive atmospheres, such
as in the presence of flammable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes. 3. Keep children and bystanders
away while operating a power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY 4. Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will reduce risk of electric
shock. 5. Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded. 6. Do not expose power tools to
rain or wet conditions. Water entering a power tool will increase the risk of
electric shock. 7. Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase the risk of
electric shock. 8. When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use reduces the
risk of electric shock.
9. If operating a power tool in a damp location is unavoidable, use a
residual current device (RCD) protected supply. Use of an RCD reduces the risk
of electric shock.
PERSONAL SAFETY 10. Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use
a power tool while you are tired or under the influence of drugs, alcohol or
medication. A moment of inattention while operating power tools may result in
serious personal injury. 11. Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust mask, non-skid safety shoes,
hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries. 12. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source and/or battery pack,
picking up or carrying the tool. Carrying power tools with your finger on the
switch or energizing power tools that have the switch on invites accidents.
13. Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result
in personal injury. 14. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in unexpected
situations.
4
GENERAL POWER TOOL SAFETY WARNINGS
15. Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry or long
hair can be caught in moving parts.
16. If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
17. Do not let familiarity gained from frequent use of tools allow you to
become complacent and ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
POWER TOOL USE AND CARE 18. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was designed. 19. Do not use
the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled
with the switch is dangerous and must be repaired. 20. Disconnect the plug
from the power source and/or remove the battery pack, if detachable, from the
pow-
er tool before making any adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of starting the power
tool accidentally. 21. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or these instructions to
operate the power tool. Power tools are dangerous in the hands of untrained
users. 22. Maintain power tools and accessories. Check for misalignment or
binding of moving parts, breakage of parts and any other condition that may
affect the power tool’s operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly maintained power tools. 23.
Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control. 24. Use
the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended
could result in a hazardous situation. 25. Keep handles and grasping surfaces
dry, clean and free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the tool in unexpected
situations.
BATTERY TOOL USE AND CARE 26. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with another battery pack.
27. Use power tools only with specifically designated battery packs. Use of
any other battery packs may
create a risk of injury and fire. 28. When battery pack is not in use, keep it
away from other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can make a connection from
one terminal to another. Shorting the battery terminals together may cause
burns or a fire. 29. Under abusive conditions, liquid may be ejected from the
battery; avoid contact. If contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns. 30. Do not use a battery pack or tool
that is damaged or modified. Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion or risk of injury. 31. Do
not expose a battery pack or tool to fire or excessive temperature. Exposure
to fire or temperature above 130 °C may cause explosion.
5
GENERAL POWER TOOL SAFETY WARNINGS
32. Follow all charging instructions and do not charge the battery pack or
tool outside the temperature range specified in the instructions. Charging
improperly or at temperatures outside the specified range may damage the
battery and increase the risk of fire.
SERVICE 33. Have your power tool serviced by a qualified repair person using
only identical replacement parts.
This will ensure that the safety of the power tool is maintained. 34. Never
service damaged battery packs. Service of battery packs should only be
performed by the manufac-
turer or authorized service providers.
Stapler Safety Warnings
1. Always assume the tool contains fasteners. Careless handling of the
stapler can result in unexpected firing of fasteners and personal injury.
2. Do not point the tool towards yourself or anyone nearby. Unexpected
triggering will discharge the fastener causing an injury.
3. Do not actuate the tool unless the tool is placed firmly against the
workpiece. If the tool is not in contact with the workpiece, the fastener may
be deflected away from your target.
4. Disconnect the tool from the power source when the fastener jams in the
tool. While removing a jammed fastener, the stapler may be accidentally
activated if it is energized.
5. Use caution while removing a jammed fastener. The mechanism may be under
compression and the fastener may be forcefully discharged while attempting to
free a jammed condition.
6. Do not use this stapler for fastening electrical cables. It is not
designed for electric cable installation and may damage the insulation of
electric cables thereby causing electric shock or fire hazards.
7. Hold the power tool by insulated gripping surfaces, when performing an
operation where the fastener may contact hidden wiring. Fasteners contacting a
“live” wire may make exposed metal parts of the power tool “live” and could
give the operator an electric shock.
8. Do not use the power tool in locations where the ambient temperature may
reach below 0°C (32°F) or above 40°C (104°F).
9. A battery short can cause a large current flow, overheating, possible
burns and even a breakdown. · Do not touch the terminals with any conductive
material. · Avoid storing battery cartridge in a container with other metal
objects such as nails, coins, etc. · Do not expose battery cartridge to water
or rain.
10. Consecutive charging may cause overheating. If you need to recharge
batteries consecutively, wait about 15 minutes for the charger to cool.
6
SAFETY WARNINGS
Additional Safety Warnings
To prevent eye injuries, always wear OSHA required “Z87” safety glasses with
permanently attached rigid, hard plastic side shields. These safety glasses
must have “Z87” printed or stamped on them. Be sure everyone in your work area
is wearing the same type of safety glasses.
DANGER: The Fusion tool is charged with compressed air in a sealed chamber.
Prior to any service or repair, release the charge of pressurized gas. The
pressurized air must be released prior to service. Major components such as
the piston/driver assembly, gearbox, piston stop and guide body are all part
of the drive assembly. Deliberate tampering with the drive assembly may result
in the release of the driver. Any repair or upgrade requiring access to the
pressure chamber may be handled by an authorized Senco dealer or service
center. Disconnect tool from battery when: · Outside of the operator’s
supervision or control. · Performing maintenance or repair · Clearing a jam ·
Moving the tool to a new location With battery disconnected, make daily
inspection to assure free movement of workpiece contact element and trigger.
Do not use tool if workpiece contact element or trigger sticks or binds.
Always remove finger from trigger when not driving fasteners. Never carry the
tool with finger on or under trigger. Tool will eject a fastener if the
workpiece contact element is bumped and the trigger is pulled. Drive fasteners
into work surface only; never into materials too hard to penetrate. Do not
drive fasteners on top of other fasteners or with the tool at too steep of an
angle; the fasteners can ricochet and hurt someone. When using tool, care
should be taken due to possibility of tool recoil after a fastener is driven.
If workpiece contact element is unintentionally allowed to re-contact work
surface following a recoil, an unwanted fastener may be driven. Therefore,
allow tool to recoil completely off work surface after a fastener is driven to
avoid this condition. Do not push workpiece contact element on work surface
until a second fastener is desired. Please review triggering options. Do not
drive fasteners close to the edge of the work surface. The workpiece is likely
to split and the fastener could fly or ricochet and hit someone. Never use any
part of the tool (i.e., the cap or mainbody ) as a hammer. The tool may
activate or become damaged and result in an unsafe condition.
7
SAFETY WARNINGS Keep hands and other body parts away from the area shown in
the circle to avoid possible injury during operation.
Do not use tool without Danger Label on tool. If label is missing, damaged or
unreadable, contact your SENCO representative to obtain a new label at no
cost.
WARNING Tool Use
Read and understand tool labels and manual. Failure to follow warnings will
result in DEATH or SERIOUS INJURY.
Operators and others in work area MUST wear safety glasses with side shields.
Keep fingers AWAY from trigger when not driving fasteners, to avoid accidental
firing. Choice of triggering method is important. See page 13-14 for
triggering options. Never point tool at yourself or others in work area.
Always point the tool away when connecting battery. Do not alter or remove
trigger or safety. Tools shall not be modified without written approval of the
manufacturer. Use clamps or other practical ways to secure and support the
workpiece to a stable platform. Holding the work by hand or against your body
is unstable and may lead to loss of control.
8
SAFETY WARNINGS
Battery Use
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE SAVE THESE
INSTRUCTIONS This manual contains important safety and operating instructions
for SENCO battery charger VB0156 (US). Before using SENCO battery charger
VB0156 (US), read all instructions and cautionary markings on battery charger
and battery.
Do not expose charger to water, rain, or snow. Use indoors.
Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons.
To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.
Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.
Length of Cord (Feet)
25
50 100 150
RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS FOR BATTERY CHARGERS
16
16
16
14
AWG Size of Cord)
An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock.
Largo del cable (m [pies])
7,5
15
30
45
16
16
16
14
Calibre AWG del cable
Longueur du cordon (en m)
7,5
15
30
45
If extension cord must be used, make sure:
· That pins on plug of extension cord are the same number, size, and shape as
those of plug on charger;
· That extension cord is properly wired and in good electrical condition; and
· That wire size is at least as large as the one specified in the table.
16
16
16
14
Taille AWG du cordon
Do not operate charger with damaged cord or plug. If damaged, have replaced
immediately by a qualified serviceman.
Do not operate charger if it has received a sharp blow, been dropped, or
otherwise damaged in any way; take it to a SENCO Authorized Service Center.
9
BATTERY AND CHARGER SAFETY WARNINGS
Do not disassemble charger or battery cartridge; take it to a SENCO Authorized Service Center when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.
To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning.
Do not charge battery cartridge when temperature is BELOW 0°C (32°F) or
104° F
40° C
ABOVE 40°C (104°F).
32° F 0° C
Do not attempt to use a step-up transformer, an engine generator or DC power
receptacle.
Do not recharge non-rechargeable batteries.
Do not allow anything to cover or clog the charger vents.
Do not store the tool and battery cartridge in locations where the temperature
may reach or exceed 45°C (113° F).
Do not incinerate the battery cartridge even if it is severely damaged or is
completely worn out. The battery cartridge can explode in a fire.
Never attempt to connect two (2) chargers together.
This appliance is not intended for use by young children or infirm persons
unless they have been adequately supervised by a responsible person to ensure
that they do not play with the appliance.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should
be supervised to ensure that they do not play with the appliance.
For more safety information, go to www.senco.com and safety training materials
and programs visit the ISANTA website at www.isanta.org.
www.P65Warnings.ca.org.
10
Functional Operation
Removeable Cap
Belt Hook
Battery
Pressure Release Port
*For authorized service center use only.
Depth of Drive Adjustment
Trigger
Magazine Release
Workpiece Contact
Grasping Surface
Magazine Latch
ON/OFF/Mode Selector
TOOL OPERATION
LOADING THE TOOL: Open magazine via rear latch. Insert strip of staples.
· Use only genuine SENCO fasteners (see Fastener Specifications). · Do not
load with workpiece contact (safety element) or trigger depressed. Close
magazine.
UNLOADING THE TOOL: Open magazine via rear latch. Remove remaining staples. It
is normal for 4-7 staples to remain in magazine.
Tool Operation
Read section titled “Safety Warnings,” before using tool.
For best results, charge new battery before using. (see “To Charge Battery” on page 17).
Indicator LED ON
The tool should be switched off when not in use. Hold down either side of the selector switch for 1 second to turn the tool off. If left on, the tool will automatically turn off after 34 minutes.
All Fusion tools are equipped with selective-actuation triggering. This allows the user to choose between the following modes of operation:
Indicator LED ON-Flashing
Contact Actuation Pressing the side of the selector switch toward the TTT symbol (as shown) for 0.5 sec. will turn the tool on in contact-actuation mode. This is indicated by the flashing green LED of the selector switch.
12
Indicator LED ON-Solid
TOOL OPERATION
Sequential Pressing the side of the selector switch toward the T symbol (as
shown) for 0.5 sec. will turn the tool on in sequential mode. This is
indicated by the solid green LED of the selector switch.
In the “contact-actuation” mode, staples can be driven in two ways:
A
The first way:
1. Press the TTT side of the selector switch for 0.5 seconds. This will be indicated
3
by the flashing green LED on the selector switch.
1
2 2. Press the workpiece contact (safety) element against the work surface.
3. Pull the trigger and the fastener is driven.
B
The Second way:
1. Press the TTT side of the selector switch for 0.5 seconds. This will be indicated
2
by the flashing green LED on the selector switch.
1
3 2. Pull trigger.
3. Depress workpiece contact element against work surface and drive a fastener.
This mode of operation is preferred when you desire high production, rapid fastener placement.
In the “sequential-actuation” mode, staples can only be driven one way:
1. Press the T side of the selector switch for 0.5 seconds. This will be indicated by the solid green LED on the selector switch.
3 2. Position workpiece contact (safety) element against work surface and depress
1
2
the safety.
3. Pull trigger to turn on the motor and drive a single fastener.
This mode of operation is helpful when you require precise fastener placement.
The Fusion stapler may detect a jam and reposition the driver. The warning indicator on the selector switch will flash red.
13
TOOL OPERATION
This tool is equipped with an indicator light at the ON/OFF/MODE switch. See
page 14 for detailed instructions. Note: When the tool is in the sequential
mode, a fastener cannot be driven by pulling the trigger before activating the
work piece contact element. If the workpiece contact is activated for more
than 10 seconds, the workpiece contact must be released to start over. When
the tool is in contact actuation mode, if the operator holds the trigger on
for more than 3 seconds, the light will go out and the trigger must be
released to start over.
This tool is equipped with a multi-purpose light in the mode switch. The mode
sensor light will indicate that the electronic controls are energized, which
operating mode has been selected, if a jam was detected and when the battery
requires a full recharge.
Solid or Flashing Green Light Indicates the tool is energized and ready to
drive. If light does not turn on, look to be sure that the trigger or work
contact element are free to move and not in the activated position. Solid Red
Light Indicates the tool has detected an error.
Low battery. The battery will usually detect the condition first and turn the
tool off. Recharge the battery or replace with a freshly charged battery to
continue. If the tool has detected this condition first, it is usually due to
sustained extreme use. Replace the battery with a fully charged battery. The
tool detected a timing issue. This can be caused by low charge pressure, an
application requiring drive energy above the tools capacity, a loose battery
connection or broken components. Re-insert the battery or replace the battery
with a freshly charged battery. If this does not remedy the issue, refer to
the troubleshooting guide or contact an authorized service center. Flashing
Red Light Indicates a fastener jam. The tool detects a jam which is usually
due to a deformed staple wedged in the driver path. Remove the battery from
tool, re-insert battery and turn on tool. If tool does not return to normal
operation, go to next step. REMOVE the BATTERY Unload all remaining fasteners
in magazine. Make sure that any loose fastener from strip is also removed.
Access the jammed fastener via the open magazine. Carefully remove the jammed
fastener. Close the magazine. Attach charged battery to tool. Load staples
into magazine. Resume normal operation.
If the wedged fastener can’t be removed, return to an authorized service
center where the damaged fastener can be removed. Remember that the Fusion
tool contains pressurized air at all times even when the battery is removed.
14
TOOL OPERATION
12 9
6
This tool is equipped with an electronic “Time-Out” feature. This tool will temporarily be disabled under any of the following conditions:
3
1. Workpiece contact element is depressed against the work piece, but the trigger
is not pressed within approximately 10 seconds.
2. Trigger is pressed, but work piece contact element is not depressed within approximately 3 seconds. (Contact-Actuation mode only.)
· Simply release trigger and release workpiece contact element to resume
2
normal operation.
1
The tool is equipped with a last fastener lockout. The tool will not fire the last 4-7 fasteners. This feature prevents unnecessary wear on the tool and prevents the driver tip from marring the workpiece. When the tool locks out, load an additional strip and continue. It is not necessary to remove the remaining fasteners from the magazine.
This tool is equiped with a dual-purpose light on the nosepiece. The light
will indicate that the electronic controls are energized while providing
illumination of the workpiece in low light situations. The light will flash
three times when the selector switch is switched to either sequential or
contact actuation. This lets the user know that the tool is ready to fire a
fastener. The light will remain on for ten seconds when the trigger is pulled
or the work contact element is depressed.
This tool is equipped with depth-of-drive dial. Turning the dial to the right
will countersink the fastener, turning the dial to the left will leave the
fastener up or raised. Drive a fastener into a scrap piece of wood to test
depth. Turning the dial in the direction shown in the image will result in the
fastener driving deeper into the wood.
This tool is equipped with an adjustable 6 position belt hook for right and
left handed operators. The hook will safely support the tool when hanging from
joists and rafters. Rotate the knurled knob to adjust opening or to switch
from right to left side. Move black plastic cap to alternate side to complete
assembly.
15
TOOL OPERATION Whenever possible, hold the tool at a right angle to the work surface.
Indicator LED ON-Flashing
Always turn the tool off before storing. As an added protection feature, the
tool will automatically turn off 34 minutes after the last activation. If a
fastener jam occurs, the red light at the mode selector switch will flash red.
The tool will attempt to recover. If the jam is severe, the driver blade will
lock in place by design and the red flashing light will not clear. Contact an
authorized service center.
Should a minor fastener jam occur: Turn the tool off by depressing the
selector switch towards either mode symbol for approximately 1 second, then
remove battery. Insert battery and turn tool back on via mode selector switch.
Tool will attempt to recover. Should a severe fastener jam occur: Turn the
tool off by depressing the selector switch towards either mode symbol for
approximately 1 second, then remove battery. Remove fasteners from magazine.
Wear safety glasses when removing magazine.
Point nose of tool away from self and others. Follow the unloading
instructions to remove fasteners from magazine. Open the magazine.
Remember! The Fusion tool is charged with compressed air in a factory sealed
chamber. Do not push on the driver with any force or use a hammer to strike
the driver while it is visible.
Remove jammed fastener with a pliers or screwdriver. Do not tamper with the
drive assembly. Close the magazine. Insert battery and turn tool back on via
mode selector switch. Tool will attempt to recover. If tool indicates a jam
again via red light, return tool to authorized service center for evaluation
16
TOOL OPERATION
TO CHARGE BATTERY
Authorized Service Center
Red and green light flashing indicates defective battery pack. Return battery
pack to your nearest SENCO Authorized Service Center for inspection or
replacement.
Solid red indicates that the battery is charging.
When your battery pack becomes 80% charged, the red light will stay on and the
green light will flash. When battery pack is fully charged, the red light will
turn off and the green light will turn on.
After normal usage, 45 minutes of charge time is required to be fully charged.
A maximum charge time of 1 hour is required to recharge a completely
discharged battery pack. Maintenance charge is indicated when the red light
turns off while the green light flashes.
The battery pack will become slightly warm to the touch while charging. This
is normal and does not indicate a problem.
Battery is constructed with 4 LED lights built into a panel on the battery
pack. These 4 LEDs reveal the state of charge and indicate possible problems
inside the battery pack.
State of Charge: Press raised green button on battery pack to check charge.
Red Flashing = 015% charge Red On = 1625% charge Red and Yellow On = 2650%
charge Red Yellow and Green On = 5175% charge All On = 76-100% charge
17
TOOL OPERATION
BATTERY CHARGER LABEL REFERENCE
MODE Standby Evaluate Charging
CHARGER LABEL ICON —-
Evaluating / HOT
BATTERY PACK INSERTED? RED LIGHT/GREEN LIGHT
No
OFF / OFF
Yes
FLASH / OFF
Yes
ON / OFF
80% Charge
Yes
ON / FLASH
Fully Charged
Yes
OFF / ON
Maintenance Defective
—-
Yes
OFF / FLASH
Yes
FLASH / FLASH
Battery Disposal · To preserve natural resources, please recycle or dispose of
properly.
This product contains Li-Ion. Local state or federal laws may prohibit
disposal of Li-Ion batteries in ordinary trash. · Consult your local waste
authority for information regarding available recycling and/or disposal
options. · For more information on battery recycling call 1-800-8BATTERY.
Maintenance
Read section titled “Safety Warnings” before maintaining tool.
1. With battery removed, make daily inspection to ensure free movement of
workpiece contact and trigger. Do not use tool if workpiece contact or trigger
sticks or binds.
2. Lubrication of the feed system is not necessary. DO NOT OIL.
3. Wipe tool clean daily and inspect for wear, especially the workpiece
contact. Replace as necessary.
WARNING Repairs other than those described here should be performed only by
trained,
qualified personnel. Contact SENCO for information at
1-800-543-4596.
Accessories
SENCO offers a full line of accessories for your SENCO tools, including:
· Battery · Belt Hook · Battery Charger · Safety Glasses For more information
or a complete illustrated catalogue of SENCO accessories, ask your
representative or www.senco.com.
18
Fastener Specifications
1/4″ 6,4 mm
1/2″ 1,3 mm
.044″ 1,1 mm
Min. 3/8″ (9.5 mm)
A
Max. 1-1/2″ (38 mm)
SENCO Fastener Code
L06 L07 L08 L10 L11 L12 L13 L14 L15 L17
A IN. MM 3/8 9,5 7/16 11 1/2 13 5/8 16 3/4 19 7/8 22 1 25 1-1/8 28,5 1-1/4 32 1-1/2 38
Technical Specifications
F-LXP
TECHNICAL SPECIFICATIONS
Voltage
18 volts Li-ion
Weight with Battery
6.6 lbs. (3.0 kg)
Height
12.4″ (31,5 cm)
Length
10.4″ (26,4 cm)
Width
3.8″ (9,5 cm)
Recharge Time
45 minutes
Fastener Capacity
110
Fastener Range
.375″ – 1.5″ Length (9,5 mm – 38 mm)
Collation Angle
0°
19
Troubleshooting
Problem/Symptom
Probable Cause
Corrective Action
Pressing mode switch does not result in green light.
Check battery. PCB is not energized.
Remove and reattach.
Check that trigger and contact are free to move.
Then choose mode selector.
Electronic components damaged. Return to an authorized service center.
Red light on.
Low battery.
Recharge or replace battery.
Check battery connection at tool.
Red light flashes.
Fastener jam.
Remove battery and re-start.
Tool will attempt to recover.
Remove battery again.
Check if staple is blocking next fastener.
Inspect magazine for bent staple.
Open magazine and inspect guide body.
Tool does not function.
Return to service center for repair.
Note: if tool has jammed and the mechanism initiates an automatic recovery, the tool may make a series of clicks as it repositions the driver. This is normal.
Tool will not start or runs slowly. Battery is discharged or has dead Replace or recharge battery. cell.
Workpiece contact element is jammed.
Remove battery, then inspect tool to assure free movement of workpiece contact element.
Drive piston has failed.
Return tool to authorized SENCO service representative.
Workpiece contact element or trigger switches are damaged.
Return tool to authorized SENCO service representative.
Tool does not drive fastener to desired depth.
Improper depth-of drive setting.
Refer to operators manual for proper adjustment.
Tool not pressed firmly against the Hold tool firmly in place when
workpiece.
driving fastener.
Drive application is too rigorous. Pressure loss.
Refer to operators manual for appropriate applications.
Return tool to authorized SENCO service representative.
20
Problem/Symptom Tool runs but will not drive fastener.
Poor feed/ tool jamming. Broken or worn driver. Tool does not fully return.
TROUBLESHOOTING
Probable Cause Battery is discharged or has a dead cell. Staple jam in
guidebody.
Mechanism requires repair.
Tool is overheated.
Driver tip not located above fastener. Debris build-up in mechanism. Driver
tip not located above fastener.
Weak battery.
Corrective Action
Recharge or replace with fresh battery.
Refer to operators manual for jam-clearing instructions.
Return tool to authorized SENCO service representative.
Allow tool to cool and insert fresh battery.
Recharge battery and allow tool to automatically retract driver.
Clean tool, clean magazine or inspect feeder spring.
Return tool to authorized SENCO service representative.
Recharge battery and allow tool to automatically retract driver.
Ensuring the long life of your Cordless Finish tool
Welcome to SENCO’s family of products. SENCO brings 50 years of commitment to
our customers and to power fastening systems. We are dedicated to making sure
your tools are performing at their best, and we understand that ensuring the
long life of your tools is important. Here are some operational and service
tips.
· Start with fully charged batteries at the beginning of each work day. · Set
the depth of drive on your SENCO tool so fasteners are not over-driven. · To
maximize battery life, follow storage recommendations and charging
recommendations in this manual. · Keep your Cordless Stapler as clean and free
of debris as possible. · Service your SENCO tool periodically to insure your
tool is productive and helping you earn money on the job.
See the service guide below for recommended service intervals.
If your Cordless Stapler does require service, dedicated SENCO servicing
dealers are available for you. For the location nearest you, call SENCO’s
Action line at 1-800-543-4596 or visit
SENCO’s website (www.senco.com).
Recommended service includes · Check Electrical System · Check Feed System ·
Check Drive Track · Add Grease to Piston and Driver
21
Limited Warranty SENCO® Pneumatic, DuraSpin®, Cordless Tools
& Compressors
Senco Products, Inc. (“SENCO”) designs and constructs its products using the
highest standards of material and workmanship. SENCO warrants to the original
retail purchaser that the following products will be free from defects in
material or workmanship for the warranty period specified below:
Products Pneumatic Tools * Fusion Tools Gas Tools Duraspin Tools
New Five Years Two Years Two Years Five Years
Reconditioned One Year Six Months Six Months 90 Days
Products Air Compressors Combo Kit Tools Multi-Blow Hand Nailers Stapling Hammers
New One Year One Year One Year One Year
Reconditioned 90 Days 90 Days 90 Days 90 Days
During the warranty period (which begins on the purchase date), SENCO will
repair or replace, at SENCO’s option and expense, any product or part that is
defective in materials or workmanship after examination by a SENCO Authorized
Warranty Service Centre, subject to the exceptions, exclusions and limitations
described below. Any replacement product or part will carry a warranty for the
balance of the warranty period applicable to the replaced product or part. A
DATED SALES RECEIPT OR PROOF OF PURCHASE FROM THE ORIGINAL RETAIL PURCHASER IS
REQUIRED TO MAKE A WARRANTY CLAIM. Warranty registration is also required and
can be accomplished through on-line Product Registration at www.senco.com or
by completing and returning the postage paid warranty registration form
included with your Operator’s manual/parts chart information, found inside the
product carton. To make a warranty claim, you must return the product, with
proper receipt/proof of purchase and return transportation charges prepaid, to
a SENCO Authorized Warranty Service Centre. A list of SENCO Authorized
Warranty Service Centres can be found at www.senco.com or by calling
1-800-543-4596 toll free. SENCO will
perform its obligations under this warranty, within a reasonable time after
approval of the warranty claim.
SENCO Cordless: 1. Subject to the exceptions, exclusions and limitations
described below, SENCO warrants that the SENCO Cordless tool will be free from
defects in materials and workmanship for two years after the purchase date. 2.
SENCO warrants that the batteries and chargers used with SENCO Cordless tools
will be free from defects in material and workmanship for one year after the
purchase date. WARRANTY EXCLUSIONS
The following warranty exclusions apply: 1. Normal wear parts are not covered
under this warranty. Normal wear parts include, for example, isolators, drive
belts, air filters, rubber o-rings, seals, driver blades, piston stops, and
piston/driver assembly. 2. This warranty does not cover parts damaged due to
normal wear, misapplication, misuse, accidents, operation beyond the
recommended speeds or voltage (electric units only), improper storage, or
damage resulting during shipping. 3. Products used in production/industrial
applications as defined by SENCO are excluded from this warranty. 4. Labour
charges or loss or damage resulting from improper operation, maintenance or
repairs are not covered by this warranty.
GENERAL WARRANTY CONDITIONS This warranty will be honoured only if:
A. Clean, dry, regulated compressed air has been used, at air pressure not
exceeding the maximum indicated on the tool casting; B. No evidence of abuse,
abnormal conditions, accident, neglect, misuse or improper modifications or
storage of the product; and C. No deviation from operating instructions,
specifications, and maintenance schedules exists (read Operator Manual for
use, specifications, and mainte-
nance instructions).
THIS WARRANTY IS THE ONLY WARRANTY ON THE PRODUCT, AND SENCO DISCLAIMS ALL
OTHER WARRANTIES. ANY IMPLIED WARRANTIES WILL BE LIMITED IN DURATION TO THE
APPLICABLE WARRANTY PERIOD SPECIFIED ABOVE. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY
NOT APPLY TO YOU. YOUR REMEDIES ARE SOLELY AND EXCLUSIVELY AS STATED ABOVE.
SENCO SHALL IN NO EVENT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, OR
SPECIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY
NOT APPLY TO YOU. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL SENCO’S LIABILITY
EXCEED THE PRICE OF THE PRODUCT WHICH HAS GIVEN RISE TO THE CLAIM OR
LIABILITY. ANY LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL
TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIOD SPECIFIED ABOVE. NO
EMPLOYEE OR REPRESENTATIVE OF SENCO OR ANY DISTRIBUTOR OR DEALER IS AUTHORIZED
TO MAKE ANY CHANGE OR MODIFICATION TO THIS WARRANTY.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
REPLACEMENT OF TOOL DUE TO NATURAL DISASTER SENCO will replace any tool
destroyed by an Act of God such as flood, earthquake, hurricane or other
disaster resulting only from the forces of nature. Such a claim will be
honoured provided that the original retail purchaser had previously submitted
a completed warranty registration card for the tool, and then submits proof of
ownership and an acceptable statement describing such Act of God documented by
an insurance carrier, police department, or other official governmental
source. To obtain instructions for filing a claim call
1-800-543-4596.
CUSTOMER SATISFACTION One hundred percent customer satisfaction is our #1
goal. If for any reason the product does not perform to the original
purchaser’s satisfaction, it can be returned to the place of purchase within
thirty days with dated sales receipt for a full refund of the purchase price
(applies to new product sales only).
© 2021 by KYOCERA-SENCO INDUSTRIAL TOOLS CINCINNATI, OHIO 45244-1611 USA
www.senco.com 091013
KYOCERA-SENCO Industrial Tools, Inc. 8450 Broadwell Road Cincinnati, Ohio 45244 www.senco.com
© 2021 by KYOCERA-SENCO Industrial Tools, Inc.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>