Sandberg 134-30 ConfCam PTZ x10 Remote 1080P User Guide
- June 6, 2024
- Sandberg
Table of Contents
Sandberg 134-30 ConfCam PTZ x10 Remote 1080P
Product overview
-
Lens
-
IR receiver
-
USB2.0: USB 2.0 Video output interface
-
IR receiver
-
DC 12V IN: Power supply
-
VISCA: RS-232, RS-485 control
Mounting options
Connection
Software installation
The camera works driver-less and is compatible with most chat-applications.
The camera has no built in microphone. We recommend to use the camera
together with Sandberg
Speaker Phone or another audio device with microphone and speaker.
Choose this device name on the device list for video-camera:
Remote control
Open the back of the remote control and insert 2 x AAA batteries.
OSD Menu Introduction
DOME OSD
Press the “Dome OSD” button on the remote control to log in Dome Menu as
follow. Press again same button to log-off OSD Menu.
DOME Menu
Protocol
Dome Address: Choose dome address ――― Adjustable Value: 1-7; Default: 1
Dome Protocol: Choose control protocol ――― Optional: Visca/Pelco_D; Default:
Visca
Buadrate: Choose baud rate ――― Optional: 2400/4800/9600/38400 Default: 9600
Back: Back to previous menu
Dome
IR Address: Choose IR address ――― Adjustable Value: 1-3; Default: 1
Pan Speed: Pan movement speed ――― Adjustable Value: 1-24; Default: 14
Tilt Speed: Tilt movement speed ――― Adjustable Value: 1-18; Default: 10
Preset Freeze: Image freezing during preset call ――― Optional: On/Off;
Default: Off
Preset Resume: Location resume ――― Optional: Off/30s/60s/90s; Default: 30
(When camera stay 30 seconds before power off where could be save as a Preset,
and camera will return this Preset after Power on)
Back: Back to previous menu
Information
Version: Firmware version info
Model: Camera model info
Date: Firmware version date
- The information may vary according to product updates
Language
OSD menu language
Exit
Log-off DOME OSD Menu
LENS OSD
Press the “Lens OSD” button on the remote control to log in Lens Menu as
follow. Press again same button to log-off OSD Menu.
LENS Menu
Exposure
Brightness: Adjust image brightness ――― Adjustable Value: 0-255; Default: 64
Backlight: Adjust the backlight ――― Optional: Off / On; Default: Off
AE: Adjust the exposure settings ――― Optional: Auto/ Shutter; Default: Auto
Shutter: Shutter speed ――― Optional: 1/10000-1/25; Default: 1/25
Flicker: Anti-fliicker adjustment ――― Optional: 50/60; Default: 50
Back: Back to previous menu
Color
Hue: Adjust image hue ――― Optional: 0-100; Default: 50
Saturation: Adjust image saturation ――― Optional: 0-100; Default: 50
Sharpness: Adjust image sharpness ――― Optional: 0-127; Default: 50
WB: Select white balance mode ――― Optional: Auto/Manual; Default: Auto
Color Temp: Adjust color temperature ――― Optional: 1500-15000; Default: 5000
Back: Back to previous menu
Image
Image Flip: Mirror and rotate image ――― Optional: Off/All/Flip/Mirror Default:
Off
Frame: Select video frame rate ――― Optional 30/25; Default: 30
Image Mode: Select image style ――― Optional Normal/Clear/Bright/Beauty
Default: Normal
Back: Back to previous menu
Information
Version: Firmware version info
Model: Camera model info
Date: Firmware version date
Information
- The information may vary according to product updates
Languag e
OSD menu language
OSD Mirror
Mirror the On Screen Display menu
Exit
Log-off DOME OSD Menu
Notes:
- No Pan/Tilt movement function while OSD Menu on screen.
- Address code, protocol, baud rate, picture freeze, preset memory function do not change after Reset of remote control.
- Shutter can only be adjusted if it is selected as Shutter in the AE menu.
Special Preset Instruction
Preset Position
| Functions
---|---
76|
Enter stand-by status
84
| Starting up 30s/60s/90s save preset bits, call each time, switch once. Low
end models only support 30s calls, no 60s and 90s function.
87|
Switch the remote controller address code 1(default value) 2, 3, once a call, switch once.
88
| Switch control protocol VISCA (default), Pelco-D, once a call, switch once.
89|
Switch baud rate 9600bps(default), 38400bps, once a call, switch once.
90
| Image flip / mirror image
94|
Restart camera and return default settings
Special Preset, the user can only call to realize its function and cannot set them up. In addition, it can not be called through the remote control, can only be called through control software (e.g. HD Camera Debugger), effective immediately after the call is completed.
Remote Control
Function Description
| S/N | Regional | Keynote | Functions |
|---|---|---|---|
| 1 | Reset | Restart camera and back to default factory settings. | |
| Power ON/OFF | Power ON/OFF | ||
| 2 | Camera ID Choose |  | Choose camera according to your |
remote control (“4” is reserved key)
3| Pan/Tilt control| | Move camera up-side
| Move camera down-side
| Move camera go left
| Move camera go right
| Return to the original position
4| Lens Focus adjustments| | Auto focus automatically
| Manual focus
| Lens zoom in far end
| Lens zoom in Near end
5| ZOOM Control| 
| Zoom out / in
6| OSD Menu| | Login Dome OSD Menu (Press again to log-off OSD.)
| Login Lens OSD Menu (Press again to log-off OSD.)
| Control the camera flip and mirror image
7| Preset position Function Area| | To “Set” as preset position
| To “Clear” preset position
| To “Call” preset position
8| Numbers key area| 
| Numbers key 1 to 6 used for
Presets.
Support
http://helpdesk.sandberg.world/
Warranty
There is a five-year warranty on your Sandberg product.
Please read the warranty terms and register your new Sandberg product at
www.sandberg.world/warranty
For information on handling electronic waste, see www.sandberg.world/weee
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>