Enji Prime TH-65 Instant Flexible Digital Thermometer User Manual

Enji Prime TH-65 Instant Flexible Digital Thermometer

Read instructions carefully before using the Digital Thermometer.

WARNING Choking Hazard:

• Thermometer cap may be fatal when swallowed. Do not allow children to use this device without parental supervision.
• Do not use thermometer in ear. Designed for use in oral, rectal and armpit (axilla) readings only.
• Do not place thermometer near extreme heat, it may explode.
• Use of the Probe Cover may result in a 0.2oF (0.1oC) discrepancy from actual temperature.
• Remove battery from the device when not in operation for a long time.
• The use of temperature readings for self-diagnosis is dangerous. Consult your doctor for the interpretations of the results. Self-diagnosis may lead to the worsening of the existing disease conditions.
• Do not attempt to get measurements when the thermometer is wet as inaccurate readings may result. Do not bite the thermometer. Doing so may lead to breakage and/or injury.
• Do not attempt to disassemble or repair the thermometer. Doing so may result in inaccurate readings.
• After each use, disinfect the thermometer especially in case the device is used by more than one person.
• Do not force the thermometer into the rectum. Stop insertion and abort the measurement when pain is present. Failure to do so may lead to injury.
• Do not use thermometer orally after being used rectally. We advise you to purchase our Probe Covers for better hygiene when used by the whole family.
• For children who are two years old or younger, please do not use the devices orally if the unit has been stored at temperatures over 41℉～104℉ (5℃～40℃), leave it in 41℉～104℉(5℃～40℃) ambient temperature for about 15 minutes before using it.

This digital thermometer provides a quick and highly accurate reading of an individual’s body temperature. The digital thermometer is intended to measure the human body’s temperature in regular mode orally, rectally or under the arm, and the device is reusable for clinical or home use on people of all ages. To better understand its functions and to provide years of dependable results, please read all instructions first.

This appliance conforms to the following standards:
ASTM E1112 Standard Specification for Electronic Thermometer for Intermittent Determination of Patient Temperature, ISO 80601-2-56 Medical electrical equipment —Part 2-56:Particular requirements for basic safety and essential performance of clinical thermometers for body temperature measurement, IEC 60601-1-11 Medical electrical equipment —Part 1-11: General requirements for basic safety and essential performance –Collateral Standard: Requirements for medical electrical equipment and medical electrical systems used in the home healthcare environment and complies with the requirements of IEC 60601-1-2(EMC), AAMI/ANSI ES60601-1(Safety) standards. And the manufacturer is ISO 13485 certified.

DIRECTIONS

1. Press the On/Off Button next to LCD display. A tone will sound as the screen shows, followed by last recorded temperature. After showing the self-test temperature, the thermometer is now in the testing mode.

2. Position the thermometer in desired location (mouth, rectum, or armpit).
   a. Oral Use: Place thermometer under tongue as indicated by  position shown in Figure 2. Close your mouth and breathe evenly through the nose to prevent the measurement from being influenced by inhaled/exhaled air. Normal temperature between 96.3oF and 99.1oF (35.7oC and 37.3oC).
   b. Rectal Use: Lubricate probe tip with petroleum jelly for easy insertion. Gently insert sensor approximately 1 cm (less than ½”) into rectum. Normal temperature between 97.2oF and 99.9oF (36.2oC and 37.7oC). c. Armpit Use: Wipe armpit dry. Place probe in armpit and keep arm pressed firmly at side. From a medical viewpoint, this method will always provide inaccurate readings, and should not be used if precise measurements are required. Normal temperature between 95.4oF and 98.1oF (35.2oC and 36.7oC).

3. The degree sign flashes throughout the testing process. When flashing stops, a soft alarm will beep. The reading may take from 10 to 30 seconds depending on where the computer is used. The measured reading will appear on the LCD simultaneously. The minimum measurement time until the signal tone (beep) must be maintained without exception. The measurement continues even after the buzzing notification. So that in order to achieve better body temperature measurement result, recommend to keep the probe in mouth and rectum about 2 minutes, or in armpit about 5 minutes regardless of the beep sound and at least 30 seconds measurement interval should be maintained in the first few uses.

4. To prolong battery life, press the On/Off Button to turn unit off after testing is complete. If no action is taken, the unit will automatically shut off after around 10 minutes.

TROUBLESHOOTING

L o

| Temperature taken is lower than 90.0°F(32.0°C)| Turn off, wait one minute and take a new temperature via close contact and sufficient rest.
H i| Temperature taken is higher than 109.9°F(42.9°C)| Turn off, wait one minute and take a new temperature via close contact and sufficient rest.
Err| The system is not functioning properly.| Unload the battery, wait for 1 minute and repower it. If the message reappears, contact the retailer for service.
****| Dead battery: Battery icon is flashing, can’t measure.| Replace the battery.

How To Calibrate Your Thermometer:

The thermometer is initially calibrated at the time of manufacturing. If the thermometer is used according to the manual, periodic readjustment is not required. However, we recommend conducting a quick calibration to confirm that your unit didn’t get damaged during shipment. A quick way to calibrate your unit is by doing the water test. Dip the tip of the thermometer into a cup of hot water. Wait for your thermometer to show ‘Hi’ or a high temperature reading number on its LCD display (for example it shows 38 °C or 100 °F). Then let it sit for a minute or two then dip it into a cup of cold water. Your display should show ‘Lo’ (meaning low temperature not low battery) or a low temperature reading number this time (for example it shows 33 °C or 91°F). Leave it at room temperature for 30 minutes and try using it again, and if it does not show ‘Hi’ or ‘Lo’ it will mean you have successfully checked your thermometer and good to go! If you find that your reading is very low and/or not changing on the LCD display at all, please get in touch with us through email with your Amazon Order ID.

SYMBOL EXPLANATION

CLEANING & DISINFECTION

Wipe the thermometer with a soft clean cloth. For stubborn stains, wipe the thermometer with a cloth that has been dampened in water or in neutral detergent solution and then wring thoroughly. Finish by wiping with a soft dry cloth. For disinfection, 75% Ethanol or Isopropyl alcohol can be used. Observe the following to prevent damage to the thermometer:

• Do not use benzene, thinner, gasoline or other strong solvents to clean the thermometer.
• Do not attempt to disinfect the sensing section (tip) of the thermometer by immersing in alcohol or in hot water (water over 122oF/50oC).
• Do not use ultrasonic washing to clean the thermometer.

oF/oC SWITCHABLE
Temperature readings are available in the Fahrenheit or Celsius scale (oF/oC; located in the upper right corner of LCD). With the unit off, press and hold On/Off Button for approximately 2 seconds to change the current setting.

SPECIFICATIONS

/oF chosen by manufacturer)

Accuracy:| 0.2oF   0.1oC) during 95.9oF ~ 107.6oF (35.5oC ~ 42.0oC) at 64.4oF ~

82.4oF (18oC ~ 28oC) ambient operating range  0.4oF ( 0.2oC) for other measuring and ambient

operating range

Operating mode:| Direct Mode
Display:| Liquid crystal display, 3 ½ digits
Memory:| For storing the last measured value
Battery:| One 1.5 V DC. Button battery (size

LR41 or SR41, UCC 392)

Battery life:| Approx. 200 hours of continuous operation of 1 year with 3

measurements per day

Dimension:| 13.9 cm x 2.2 cm x 1.2 cm (L x W x H)
Weight:| Approx. 12 grams including battery
Expected service

life:

| Three years

Ambient operating range:

| Temperature: 41oF ~ 104oF (5oC ~ 40oC)

Relative humidity: 15% ~ 95% RH Atmospheric Pressure: 700hPa ~

1060hPa

Storage and transportation condition:| Temperature: -4oF ~ 131oF (-20oC ~ 55oC)

Relative humidity: 15% ~ 95 % RH

Atmospheric Pressure: 700hPa ~ 1060hPa

Ingress Protection

Rating:

| IP 27
Classification:| Type BF

BATTERY REPLACEMENT

1. Replace battery when appears in the lower right corner of LCD display.
2. Pull battery cover off as shown in Figure 3.
3. Gently pull out plastic circuit board with battery chamber approximately 1 cm (slightly less than ½”.) (See Figure 4)
4. Use pointed object such as a pen to remove old battery. Discard battery lawfully. Replace with new 1.5 V DC button type LR41 or SR41, UCC392, or equivalent. Be sure battery is installed with “+” polarity facing up. (See Figure 5)
5. Slide battery chamber back into place and attach cover.

All rights reserved. HAPPY CARE BY ENJI info@enji-prime.com www.enji-prime.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>