hama 00176606 WiFi Wall Light Instruction Manual

hama 00176606 WiFi Wall Light Instruction Manual

Thank you for choosing a Hama product.
Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for future reference. If you sell the device, please pass these operating instructions on to the new owner.

Explanation of symbols used on the product label

| Electrical device of safety class II.
Protection against electric shock thanks to reinforced or double insulation of live parts.
---|---
| The product must only be used with alternating current.
| Non-dimmable.
The lamp is not suitable for use with a conventional dimmer.

| The article may only be con- nected by a qualified electrician who complies with national regulations and those of the lo- cal energy supply company, and who has sufficient knowledge regarding installation locations, fire protection and electrical installation work.

• Replaceable control gear by a professional

Explanation of warning symbols and notes

Risk of electric shock

This symbol indicates a risk of electric shock from touching product parts carrying hazardous voltage.

Warning

This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.

Note

This symbol is used to indicate additional information or important notes.

Package contents

1. 1 Wall light
2. 2 Insulation tubes
3. Mounting hardware
4. Quick-start guide

Safety instructions

• This product is intended for private, noncommercial use only.

• Use the product only for the intended purpose.

• Do not drop the product and do not expose it to any major shocks.

• Do not operate the product outside the power limits specified in the technical data.

• Do not modify the product in any way. Doing so voids the warranty.

• Children must not play with the device. Cleaning and user maintenance must not be carried out by children without supervision.

• As with all electrical products, this device should be kept out of the reach of children.

• Dispose of packaging material immediately in accordance with the locally applicable regulations.

• The product must only be operated on a supply network as described on the type plate.

• Before mounting, check that the wall you have chosen is suitable for the weight to be mounted.
  Also make sure that there are no electric, water, gas or other lines running through the wall at the mounting site.

• Electrical cables must never become trapped or twisted between the product and the surface.

• If the product is attached to a metal surface, it must be connected to an earth lead or the installation’s potential equalising cable.

• Only use the article under moderate climatic conditions.

• Do not use the product in areas in which electronic products are not permitted.

• Do not use the product in a damp environment and avoid splashing water.

• Do not bend or crush the cable.

• Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.

• Do not continue to operate the device if it is visibly damaged

• No bare spots must be visible after connection

Warning

• Please note that lights (even LEDs) can generate heat and may become hot. Always let the light cool down for a few minutes before touching it.
• The device can only be operated on a 230V 50 Hz AC voltage network.  Work on the 230 V network must only be carried out by an electrician certified in your country. The applicable accident prevention regulations must be adhered to.
• To avoid an electric shock from the device, please disconnect the mains voltage (switch of the automatic circuit breaker). Failure to comply with the installation instructions can cause fires or other hazards.

Risk of electric shock

Do not open the product and do not operate it if it is damaged, if smoke, a strange smell or loud noises are coming from it. Immediately contact your dealer or our service department (see item “Service and Support”).

Note

The light source of this light is not replaceable; when the light source has reached the end of its life, you need to replace the entire light.

Warning

Never look straight into the light source and do not aim its beam of light straight into the eyes of other people or animals. This could damage your/their eyes.

Note

This light contains a light source of energy efficiency class “F”.

Product characteristics

• The SMART LED light can be connected to your wireless home network via WiFi and serves as illumination in indoor rooms or outdoor areas.
• It can be controlled via a mobile device (mobile phone/tablet) as well as via the Amazon Alexa /Echo and Google Home Voice services.
• A selection of voice commands is available, such as:
  Switch on / off
  “Alexa / OK Google, switch the light on / off.” Dim to X %
  “Alex / OK Google, reduce the light to X %”. Dim by X %
  “Alexa / OK Google, increase the light X %.” Colour temperature selection
  “Alex / OK Google, switch the light to warm white.” (white, daylight, etc.)

Installation

• Switch off the relevant fuse (fuse box) for the room in which you wish to install the light.
• Check that the wires are de-energised using a suitable measuring device (e.g. multimeter).
• Pull the housing upwards and off.
• Loosen the grub screws on the side using the Allen key provided.
• Never look straight into the light source and do not aim its beam of light straight into the eyes of other people or animals. This could damage your/their eyes.
• Please note that lights (even LEDs) can generate heat and may become hot. Always let the light cool down for a few minutes before touching it.
• Pull the wires through the hole (with rubber insulation) on the mounting plate and attach the insulation tubes. The tubes must cover the connecting cable inside the light up to the terminals. Shorten any connecting wires that are too long.
• Insulate the cables as specified on the terminals (10 mm).
• No earth wire can be connected to the lamp, nor should it be.
• Attach the mounting plate to the wall using the screws and dowels supplied.
• Connect the wires to the light terminals. Please ensure that the seal is correctly inserted.
• Place the wall light on the mounting plate and tighten the grub screws on the side.
• Now push the housing back onto the wall light.

Integrating devices into the Hama Smart Solution app

• Switch the fuse back on.

• Connect the product to your wall switch.

• The product starts to flash quickly. If it does not, switch it ON and OFF 3 times using the light switch.

• Now open the Hama Smart Solution app and sign in.

• Press the “+ in the top right-hand corner to add a new device.
  

• Choose Lights from the list.

• Next enter your WiFi password and confirm with OK.

• Now confirm that the product is flashing quickly and click Next.

• Your product is now connected.

• Once the connection is successful, the product stops flashing quickly and the app confirms that the connection was successful. You can now assign it a different name if you wish.
  

• Click Finish to end the process.

• You can now control your product.

Setting options

The following settings can be made in the app:

can be stored here and selected at the press of a button.
3| Colour slider| Set the preferred colour temperature here.
4| Brightness slider| Set the preferred brightness here.
5| Countdown| Once the set time has elapsed, the light is automatically switched on or off.
6| On/Off button| Switch the light on or off with the press of a button.
7| Timeline| Create time-controlled programmes here.

For extended usage options, scenarios can be created in the app.
(See Section 9 and App Guide)

Extended usage options with scenarios

Scenarios and automated sequences, which can be created in the app in the “Smart scenarios” section, can be used to create many combination and usage options for these products, depending on the Smart Home products you have installed.

Programming is always via the app (see Section 4 of the App Guide) and will be offered / suggested to you on an individual basis.

• Standard usage option
  
  

• Extended usage option
  
  

Care and maintenance

Note

Disconnect the product from the mains before cleaning and during prolonged periods of non-use.

• Only clean this product with a slightly damp, lint-free cloth and do not use aggressive cleaning agents.
• Ensure that no water is able to enter the product.

Warranty disclaimer

Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.

Recycling information

Note on environmental protection:

Following the implementation of European Directives 2012/19/EU and 2006/66/EU into the national legal systems, the following applies:
Electrical and electronic devices as well as batteries must not be disposed of with household waste. Consumers are obliged by law to return electrical and electronic devices as well as batteries to the designated public collection points or to the point of sale at the end of their service lives.
Detailed information on this topic is defined in the national laws of the respective country. This presence of the above symbol on the product, operating instructions or package indicates that the product is subject to these regulations. By recycling, reusing the materials or other forms of utilising old devices/batteries, you are making an important contribution to protecting our environment.

RF exposure information

This device complies with the EU requirements for limiting the exposure of the general public to electromagnetic fields by means of health protection.
The device complies with RF specifications provided it is used 20 cm away from the body.

Declaration of conformity

Hama GmbH & Co KG hereby declares that the radio equipment type [00176606, 00176607] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following Internet address: www.hama.com->00176606, 00176607 ->Downloads.

Technical data

WiFi Wall Light|
---|---
Luminous flux| 360 lm
Light output| 3.6 W
Connected load| 6 W
Light colour| 2700% – 6500% (warm white to cold white)
Input voltage| 220-240V~ / 50Hz
Frequency band/ frequency bands| 2.4 GHz
Maximum radio- frequency power transmitted| < 100 mW

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>