KEURIG K150P Commercial Brewing System Owner’s Manual

: June 6, 2024
: Keurig

KEURIG K150P Commercial Brewing System Owner’s Manual

IMPORTANT SAFEGUARDS

Safe Operation & Use

When using electrical appliances, basic safety precautions should be followed, including the following:

Read all instructions before using.
Do not touch hot surfaces. Use handles and knobs when available.
This appliance must be properly installed and located in accordance with these instructions before it is used.
The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electrical shock or injury to persons.
Do not place on or near a hot gas or electric burner, or in a heated oven.
Do not use outdoors.
To protect against fire, electric shock and injury do not immerse cords, plugs, or the appliance in water or any other liquid.
Do not overfill the Water Reservoir with water.
Use only water in this appliance! Do not put any other liquids or foods in the Water Reservoir except as instructed in the Cleaning Instructions in this guide.
Turn off and unplug the brewer before cleaning or maintenance. Allow to cool before putting on or taking off parts and before cleaning the appliance.
For best operation, plug the appliance into its own electrical outlet on a dedicated circuit to prevent flickering of lights, blowing of fuses or tripping a circuit breaker.
Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is damaged in any manner. Contact Keurig Customer Service to report any malfunction of or damage to the brewer.
Do not let the cord hang over the edge of the table or counter, or touch hot surfaces.
To disconnect, press the Power Switch on the brewer to “OFF” status and then remove the plug from the wall outlet.
Close supervision is necessary when any appliance is used by or near children.
Do not lift the Handle while brewing is in progress.
Always keep the Water Reservoir Lid on the Water Reservoir unless you are refilling it.
This appliance is equipped with a power cord having a grounding wire with a grounding plug. The appliance must be grounded using a 3-hole properly grounded outlet. In the event of an electrical short circuit, grounding reduces the risk of electrical shock.
If the outlet is a standard 2-prong wall outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord or use an adapter.
Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.
Do not use the appliance for other than its intended use.
Always brew with the Puncture Plate (item S on page 5) installed. Failure to do so will result in a failure to properly brew.

Save These Instructions.

WARNING TO USERS AND PARENTS

DONOT permit children to use brewer unless there is adult supervision. Brewer dispenses very hot water.
SPECIAL NOTICE FORHOT COCOAUSERS: IMMEDIATELY AFTER USING AHOT COCOA K-CUP® PACK, RUN a Hot Water Brew Cycle without a K-Cup® pack to avoid the possibility of clogging the exit needle. DONOT assume the next user will do this.

CAUTION: There are two sharp needles that puncture the K-Cup® pack, one above the K-Cup® Pack Holder and the other in the bottom of the K-Cup® Pack Holder. To avoid risk of injury, do not put your fingers in the K-Cup® Pack Assembly Housing.

CAUTION: There is extremely hot water in the K-Cup® Pack Holder during the brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup® Pack Assembly Housing during the brewing process.

CAUTION: Please always keep the brewer in its upright position to avoid potential injury and/or damage to your brewer.

SHORT CORD INSTRUCTIONS : A short power supply cord is provided to reduce the risk of becoming entangled in or tripping over a longer cord. If an extension cord is used, (1) the marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance; (2) the cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over unintentionally; and (3) the extension cord must include a 3-prong grounding plug.

THIS PRODUCT IS FOR HOUSEHOLD AND COMMERCIAL USE

WARNING: THIS PRODUCT CONTAINS CHEMICALS, INCLUDING LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.

WARNING: RISK OF FIRE OR ELECTRIC SHOCK DO NOT OPEN !

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE THE BOTTOM COVER. NO USER SERVICEABLE PARTS ARE INSIDE. REPAIR SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY.

Set-up

Helpful Hints

Keep your brewer turned “ON” at all times. To brew a fresh cup of coffee, tea or hot cocoa anytime you want, we suggest you keep your brewer turned “ON” all the time. However, the brewer is fully programmable so you can set it to turn on and off automatically to match your schedule. Or, if you prefer, set the brewer to automatically turn off after a period of time. Follow the simple instructions on pages 13–14 to make using the brewer convenient for you.
For the best tasting gourmet coffee, tea or hot cocoa, Keurig recommends using bottled water or filtered water. Water quality varies from place to place. If you notice an undesirable taste in your cup of coffee, such as chlorine or other mineral tastes, we recommend you consider using bottled water or water from a filtration system. The Keurig™ Water Filter Starter Kit is compatible with the K150P brewer but is not NSF certified. Use of this accessory will void NSF certification.
Customize the size, flavor & brew that’s perfect for you. With the choice of over 250 varieties of K-Cup® packs and 5 brew sizes (Small Cup-4 oz., Small Mug-6 oz., Medium Mug-8 oz., Large Mug10 oz., and Travel Mug-12 oz.) your Keurig® brewer gives you endless options to customize the size, flavor and brew that’s perfect for you. For a strong, intense cup, select an Extra Bold K-Cup® pack (with up to 30% more ground coffee than regular varieties) and brew the size that’s right for you. The smaller the brew size, the more intense flavor in your cup. The larger the brew size, the less intense flavor in your cup.
Plug brewer into its own grounded outlet. If the electric circuit is overloaded with other appliances, your brewer may not function properly. The brewer should be operated on its own circuit, separate from other appliances.
Brewing into a travel mug. To brew into a travel mug, simply remove the Drip Tray Assembly and place the travel mug on the Drip Tray Base.
De-scale brewer regularly. Please see pages 16 and 17 for instructions

Unpacking Instructions

Place brewer box on a large steady surface (such as a table or countertop) or on the floor. Open the box.
Remove enclosed literature.
Turn the box on its side with the front of the box face down.
Reach into the box and grasp the foam insert that contains the brewer.
Carefully pull the foam insert toward you and out of the box. The brewer will still be encased in the polyfoam and be on its side.
Remove the top polyfoam packaging material.
Carefully lift brewer off of the bottom polyfoam and place it upright on a flat, steady surface.
Lift plastic bag off of brewer.
Record the serial number for this brewer on page 3 of this guide. The serial number can be found on the side of the brewer box or on the bottom of the brewer.
Place the brewer upright on a flat, steady surface. Remove tape holding Water Reservoir in place.

We recommend you save all packing materials in case future shipping of the product is necessary.

WARNING

Keep all plastic bags away from children.

Features

Keurig® — Model K150P Brewe

Product Overview

Back view with optional
Filter Kit #5572 connected.

Filter Kit

Keurig® K150P Brewer

A. Handle
B. Lid
C. LCD Screen
D. K-Cup® Pack Assembly Housing
E. K-Cup® Pack Holder (E and F are the K-Cup® Pack Holder Assembly)
F. K-Cup® Pack Holder Funnel
G. Drip Tray Plate
H. Drip Tray
I. Drip Tray Base
J. Housing
K. BREW Button
L. Power Switch
M. Power Cord
N. Filter Kit Part #5572 (not included)
O. Omni KQ8 Filter (not included)
P. Water Inlet Valve 3/4 Hose Connector Part #50-201004- 010 (not included)
Q. Drain Hatch and Knob
R. Drain Tubes and Plugs
S. Removable Puncture Plate

Plumbing Instructions

CAUTION: This brewer is designed to handle local water pressures from 40 psig up to 125 psig. Consult a licensed plumber for water pressures in your area. Use plumbing fittings and tubing specified to withstand 125 psig.

WARNING: Keurig requires the use of an external water filter such as the Omnipure KQ8, available from Keurig, Inc. Part No. 5572. Failure to use a filter invalidates the brewer warranty.

Plumbing Fitting Connections

An external filter (KQ8) can be mounted on the rear surface of the brewer using the mounting screws provided. See back view of brewer on page 5.
Loosen the two mounting screws located on the upper-rear of the brewer and hang the KQ8 filter kit assembly.
Tighten the two mounting screws (be careful not to over tighten).
NOTE: The KQ8A Filter assembly comes with 1/4 FPT ports for both inlet and outlet and the plumbed water inlet to the brewer is 3/4 Male Garden Hose Thread (Invensys solenoid valve). 1/4 OD LLDPE (Linear Low Density Polyethylene) tubing is recommended (NSF compliant between the filter assembly and the brewer. NSF compliant fittings are recommended such as High Density Polypropylene Type).
Connect the ‘INLET’ port of the filter assembly to the local water supply.
Connect a long length of tubing to the EXIT Port of the filter assembly. DO NOT CONNECT TO THE BREWER YET.
The filter needs an initial flush to clear any carbon deposits. Route the long length of tubing from the EXIT port to a container or sink.
Turn on water supply and allow at least 4 – gallons of water to flush through the filter.
Turn off water supply.
Cut the tubing to proper length and connect to inlet plumbing port on the brewer by using water inlet valve 3/4 hose connector available from Keurig, Inc. Part #50-201004-010 (not included).
Turn on water supply

SECTION 1 Set-Up & First Brew

IMPORTANT: You cannot use your Keurig® brewer until it has been set up for its first use.
NOTE: If brewer has been exposed to temperatures below freezing, allow brewer at least two hours to reach room temperature before brewing. A frozen or extremely cold brewer will not operate.

Setting Up Your Brewer

Remove all pieces of packing tape from the brewer and Drip Tray. Remove the clear plastic film from the LCD Display. Unwrap cord and plug the brewer into a grounded outlet.
Turn the brewer on, the Power Switch is located at the top left hand side of the brewer on the back. The brewer’s LCD Display will display the power up welcome screen (fig. 1).

fig. 1
The brewer will automatically fill the Internal Hot Water Tank with water and then the water will be heated. This will take about 3 minutes. During the heating period, “HEATING PLEASE WAIT” will be displayed on the LCD Screen (fig. 2).

fig. 2
Place a 10 oz. mug on the Drip Tray Plate, then fully raise and lower the Handle. The Brew Button will now be illuminated. Press the Brew Button to start a cleansing brew. NOTE: A K-Cup® pack should not be used for this sequence.
When the cleansing brew is complete, the brewer will go into its idle state and will be ready to brew your first K-Cup® pack.

Ready to Brew Your First Cup

The LCD Display will be in its idle state (fig. 3).

fig. 3
Lift the Handle. The K-Cup® Pack Holder will open toward you (fig. 4).

fig. 4

Select a K-Cup® pack.

NOTE: Do not remove the foil lid or puncture the K-Cup® pack.

Place a K-Cup® pack in the K-Cup® Pack Holder (fig. 5).

fig. 5
CAUTION: There are two sharp needles that puncture the K-Cup® pack, one above the K-Cup® Pack Holder and the other in the bottom of the K-Cup® Pack Holder. To avoid risk of injury, do not put your fingers in the K-Cup® Pack Assembly Housing.
Lower the Handle to close the Lid over the K-Cup® Pack Holder. (When it is closed completely, the BREW Button will flash up to 60 seconds).
Place a mug on the drip tray and select your brew size (fig. 6), then press BREW (fig. 7).

**fig. 6

fig. 7
NOTE:** If you do not press BREW within 60 seconds the brewer will return to its idle state and the Brew Button will cease to flash to prevent accidental activation. Re-activate by raising the handle fully and then closing it.

There may be a short pause prior to coffee being dispensed. The entire brew process lasts for approximately 1 minute and ends with a burst of air to remove all liquid from the K-Cup® pack.
CAUTION: There is extremely hot water in the K-Cup® Pack Holder during the brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup® Pack Assembly Housing during the brew process.
The end of brew is indicated by “KEURIG BREWED ENJOY”.
Lift the Handle, remove and dispose of the used K-Cup® pack. CAUTION: K-Cup® pack will be hot.

Stopping the Brew Process

If you need to stop the brewing after the process has started, press and release the Power Switch to turn the brewer ‘OFF’. The flow of coffee, tea or hot cocoa will stop and the heating element and the LCD Screen will shut off.

NOTE: You may get more coffee, tea or hot cocoa in your cup during your next brew. We recommend that you perform a cleansing brew with water only after a terminated brew. Then your next brew will be the volume you have selected.

Adding Water

Your brewer has been configured at the factory to be direct plumbed, however, the brewer can also be converted into a pour over model with a Cold Water Tank Spare Part. To order, please call 1.888.CUP.BREW (287.2739).

Brewing Hot Water

Your brewer is able to produce hot water for making hot cocoa from a packet, or for use in cooking, for making soups, etc. Simply follow the instructions on page 7, “Ready To Brew Your First Cup” without adding a K-Cup® pack.

NOTE: After brewing a hot cocoa pack, we recommend running a hot water brew cycle without a K-Cup® pack.

Brewing Hot Water

Purging the Brewer

If your brewer has not been used for more than one week, you should purge the water from the internal water tank.

Follow Draining the Brewer instructions.
Once drained, re-connect brewer to power source and turn on.
When the brewer indicates “READY”, place a large mug on the Drip Tray and select Large Mug (10 oz. serving) brew size from the Select Brew Size Menu (fig. 8).

fig. 8
Discard water.
Repeat steps 2 – 4 two more times to completely purge water from the Internal Hot Water Tank.

To enter the MENU MODE the brewer should be plugged in and the power must be off. Press and hold your finger on the display while pressing and releasing the Power Switch. Continue pressure on the display for 5 seconds (fig. 9). The MENU screen will appear (fig. 10).

Press any line item to enter the set up for that particular feature. Please reference the Menu navigation on page 11.

If you are experiencing any problems with your brewer, please contact Customer Service at 1.888.CUP.BREW (287.2739).

Menu Controls & Indicators
fig. 9

fig. 10

Home
Press HOME at any time to return your brewer to an idle state.

Clock
Setting the clock is optional. To program the clock, follow the instructions.

Brew Temp
The brew temperature is pre-set at 193˚F. You do not have to set the brew temperature but you can adjust it up or down by 5˚. Simply follow the instructions.

Brew Size(s)
Five brew sizes are available: 4 oz., 6 oz., 8 oz., 10 oz., and 12 oz. To program the brew sizes.

Auto OFF
Auto Off allows you to program your brewer to automatically turn off two hours after the last brew. See page 14 for programming instructions.

ON/OFF Time
You can leave your brewer on all the time and use the Power Switch to turn it off. Or you can program the brewer to brew at a specific time as shown on page 13.

Language
This brewer is shipped with English as the default language. To change the language, follow the instructions.

Contact
The contact setting features allows you to program the contact information you need for brewer support and help. To program, follow the instructions.

Menu Key Navigation

Setting the Clock

Setting the clock is optional. When the clock is set, the time will appear in the LCD Control Center. NOTE: You must set the clock if you will be programming the Auto On/Off Time feature. 1. F

From the Menu Mode, press “CLOCK”.
The set clock screen will display “DISABLED” if the brewer is new or if electrical power has been interrupted. Press “DISABLED” to set a time. Press H repeatedly to advance the hour in steps or hold it down to scroll through the hours quickly. When you have set the hour then press the M to set the minutes, press repeatedly to advance by a minute each time or keep it pressed to scroll quickly (fig. 11).

fig. 11
Press “OK” when you are finished. The Clock is now set.
The correct time should now be displayed in the LCD Home Screen

NOTE: If power is interrupted to the brewer, follow the procedure above to reset the time as the clock will not be visible. Brew size and brew temperature menu settings will be restored automatically. All other settings will be restored automatically after clock is set.

NOTE: To disable the clock, press the time. However, the ‘On/Off’ time setting will also be disabled.

Programming Brew Temperature (188°–198º F)

The brewer brews at a preset temperature of 193°F. You can adjust this temperature up or down by 5°. Simply follow the instructions below.

From the Menu Mode, press “BREW TEMP”.
The LCD Display will now display the Brew Temperature programming options (fig. 12).

fig. 14
The temperature 193°F (initial setting) will be displayed at the top of the LCD Display to indicate the current temperature setting.
Press the + symbol to increase the temperature and the – symbol to lower the temperature one degree at a time.
Once you have reached your desired brew temperature, press “OK”. The Brew Temperature is now set.
To change the brew temperature, repeat steps 1 through 4

NOTE: At high altitudes (over 5,000 feet) if boiling occurs, use the temperature adjustment (-5°) to lower the temperature.

Programming Your Brew Size

All brew sizes are enabled in the default setting. If you want to disable any brew size, just press on the appropriate icon(s). Please follow instructions outlined below.

From the Menu Mode, press “SET BREW SIZE(S)”.
The LCD will display all enabled brew sizes. To disable a brew size press the icon. The check mark will change to an “X” indicating that the brew size is disabled (fig. 13).
Once you have selected your desired brew size(s), press “OK”. The brew size(s) are now set

NOTE: You can not delete all brew sizes. To enable a brew size you have already disabled, just press its icon and then press “OK”. The 8 oz. setting is the default brew size if all sizes have been disabled.

Programming On/Off Features

The brewer provides three modes so that you can enjoy gourmet coffee, tea or hot cocoa on your own schedule.

Leave it ON all the time. The brewer can be left on all the time so that it is always ready to brew a fresh cup of gourmet coffee, tea or hot cocoa. To turn the brewer off at any time, simply press and release the Power Switch. Press and release the Power Switch again to restore power to the brewer. You will have to wait for the water to heat up before the brewer is ready to brew.
Program the brewer for a specific On/Off Time. NOTE: To use this programming feature, the clock must be set to the correct time.
- After setting the correct time (see “Setting The Clock” page 12), return to the Menu Mode and press “ON/OFF TIME”.
- To set the ON time, press “DISABLED”. The display will change to a time of day. Press “H” to set the hours and “M” to set the minutes. Once the desired time is set, press “OK” to accept this time.
- To set the OFF time, press “DISABLED”. The display will change to a time of day. Press “H” to set the hours and “M” to set the minutes. Once the desired time is set, press “OK” to accept this time (fig. 14).
  
  fig. 14
3. Set the brewer to “AUTO OFF” to automatically
turn off 2 hours after the last brew.
- From the Menu Mode, press “AUTO OFF”. The LCD Display will now display the “AUTO OFF” programming option (fig. 15).
  
  fig. 15
- To enable the “AUTO OFF” feature, press “ON”. “ENABLED” will appear on the screen and press “OK”. To disable the “AUTO OFF” feature, press “OFF”. “DISABLED” will appear on the screen and press “OK”.

Language Settings

The brewer is shipped with English as the default language. To change the default to Français or Español, follow the instructions outlined below

Set Language

From the Menu Mode, press “LANGUAGE”.
The LCD Display will now display the Language programming options (fig. 16).
fig. 16
Press the desired Language button, then press OK to confirm your selection.

Setting Contact Screen

The contact screen is pre-programmed with the following information: Keurig, Incorporated and www.keurig.com.

You can reprogram the brewer with your contact information. The contact screen will appear in the screen saver.

From the Menu Mode, press “CONTACT”.
The LCD screen will display the Keurig default contact information (fig. 17).
Press the Upper (Company Name) Box. The Keypad will appear along with the current information (fig. 18).

NOTE: Unless changed by the user, Keurig contact information will be present on the display.
Press Delete Key repeatedly to remove current information. Enter new information using the Keypad.
NOTE: To select Upper Case, Lower Case, Numerals, Upper Case Accents, Lower Case Accents, press the Keypad Change Key located at the bottom center of the screen.
b. Press “OK” to save your changes and
return to the Main Contact Screen.
NOTE: Pressing the Back Arrow Key will
return to the Main Contact Screen without
saving changes.
Press the Middle (Phone Number) Box. The Numeral Keypad Mode will appear along with the current information (fig. 19).
Delete current phone number and enter new information using the Keypad.
Press “OK” to save your changes and return to the Main Contact Screen.
Press the Lower Box. This box can be customized to contain any information such as web/email address, contact name, etc (fig. 20).
Enter new information using the Keypad.
Press “OK” to save your changes and return to the Main Contact Screen.
In Main Contact Screen (fig. 17), press “OK” to save the updated screen as the default and return to the Menu Screen.

Cleaning & Maintenance

Cleaning External Parts

Regular cleaning of the brewer’s external components is recommended. The following section provides instruction for standard cleaning procedures. For in-depth NSF certified instructions, please refer to the Cleaning and Sanitization Guide.

Never immerse the brewer in water or other liquids. The Housing and other external components may be cleaned with a damp, soapy, non-abrasive cloth.
The Drip Tray can accumulate up to 12 ounces of overflow. The Drip Tray and Drip Tray Plate should be periodically inspected and rinsed clean.
To remove the Drip Tray Assembly, simply slide it toward you, keeping it level at all times to avoid spilling. The Drip Tray and Drip Tray Plate should not be placed in the dishwasher.
fig. 21

They should be cleaned with a damp, soapy, non-abrasive cloth and rinsed thoroughly.

Cleaning the K-Cup® Pack Holder Assembly

Cleaning the Parts—The K-Cup® Pack Holder Assembly can be placed onto the top shelf of a dishwasher.
NOTE: Use low temperature cycles in the dishwasher. To remove the K-Cup® Pack Holder Assembly from the brewer, open the cover by lifting the Handle. Grasp the top of the K-Cup® Pack Holder with one hand while pushing up on the bottom of the K-Cup® Pack Holder from underneath with the other until it releases (fig. 23). After cleaning, align the K-Cup® Pack Holder with the opening using the two front ribs as a guide, and snap them into place from the top.
Cleaning the Funnel—The Funnel can be removed from the K-Cup® Pack Holder by pulling on it until it pops off (fig. 22).

The Funnel is dishwasher safe. To replace it, just snap it back onto the K-Cup® Pack Holder Assembly.
Cleaning the Exit Needle—The Exit Needle is located on the inside bottom of the K-Cup® Pack Holder Assembly. Should a clog arise due to coffee grinds, it can be cleaned using a paper clip or similar tool. Remove the K-Cup® Pack Holder Assembly and detach Funnel. Insert the paper clip (as shown in fig. 22) into the Exit Needle to loosen the clog, then flush with water.
The K-Cup® Pack Holder Assembly can be placed onto the top shelf of a dishwasher.
NOTE: Use low temperature cycles in the dishwasher.
Cleaning the Puncture Plate—The Puncture Plate can be removed by grasping the finger grips of either side and pulling forward (fig. 23).

Once removed, spray the Puncture Plate with detergent, brush clean and rinse if necessary. Be sure to replace the Puncture Plate after cleaning to ensure proper brewer operation.
CAUTION: There are sharp needles that puncture the K-Cup® pack above the K-Cup® Pack Holder and in the bottom of the K-Cup® Pack Holder. To avoid risk of injury, do not put your fingers in the K-Cup® Pack Assembly Housing.

De-Scaling Your Brewer

Mineral content in water varies from place to place. Depending on the mineral content of the water in your area, calcium deposits or scale may build up in your brewer. Scale is non-toxic, but left unattended, it can hinder brewer performance. De-scaling your brewer helps maintain the heating element and other internal parts of the brewer that come in contact with water.

The brewer should be de-scaled every 3-6 months to ensure optimal performance. It is possible for calcium deposits to build up faster, making it necessary to de-scale more often. The symptoms of scale build up are slow brewing and/or short cups.

The following outlines the steps required to prepare the brewer for the descaling procedure:

Unplug the brewer from the power supply.
Disconnect or interrupt the external water supply feeding the brewer.
Drain the Hot Water and Cold Water Tanks (see Draining the Brewer on page 17).
Remove the two screws located on the back, top, left of the brewer.
Remove the Top Cover to gain access to the internal Cold Water Tank and expose the Descaling Solution Access Port.
Reconnect the power supply.
Proceed with the descaling procedure on page 17.

De-Scaling Instructions

PREPARE
Make sure you have at least 90 oz. of undiluted white vinegar on hand. You will also need an empty sink and a large ceramic mug (do not use a paper cup).
Empty the water in the Water Reservoir.
Disable “Auto Off” and programmed “On/Off” time (pages 13-14).
FILL AND CLEAN
Pour approximately 90 oz. of the vinegar into the Water Reservoir.
Place a large mug on the Drip Tray Plate and run a water brew cycle.
DO NOT USE A K-CUP® PACK, just select the Large Mug brew size.
Pour the contents of the large mug into the sink.
Repeat the brew process 3 times.
Let the brewer stand for at least 4 hours while still on.
RINSE
Ensure the Water Reservoir is filled with fresh water.
Place a large mug on the Drip Tray Plate and run a water brew cycle.
Pour the contents of the large mug into the sink.
Repeat brew process until the Water Reservoir is empty.
You may need to perform additional water brew cycles if you notice any residual taste or odor.

Service

Beyond these recommended cleaning and maintenance procedures this brewer is not user serviceable. For service, please refer to the Warranty section of this guide.

Storage

Draining the Brewer

Turn off the brewer, unplug it, and allow the brewer to cool for 30 minutes.
Turn the brewer around so the back is facing out. Unscrew the small knob to release the back panel, remove the panel from the brewer, and set it aside. If the screw is tight, you may need to use a flathead screw driver.
Pull the tube downward until the end is free (fig. 23). Over a large pitcher, remove the plug and drain the water from the Internal Hot Water Tank into the pitcher.
CAUTION: If the brewer was not allowed to cool sufficiently, the water draining from the tube may be very hot. Re-cap the tube.
NOTE: To avoid losing parts, when finished, re-insert the tube and screw the panel back onto the brewer.
fig. 23

Troubleshooting

Situation	Solution
Brewer does not have power

Plug brewer into an independent outlet.
Check to be sure that it is plugged in securely.
Plug into a different outlet.
Reset circuit breaker if necessary.
Make sure that the Power Switch has been turned on and LCD Display is illuminated.

Brewer will not brew|

After placing the K-Cup® pack in the K-Cup® Pack Holder, make sure the Handle is pushed down securely and the LCD Control Center reads “READY TO BREW” with the BREW Button flashing, then press the BREW Button.
The Exit Needle may be clogged (refer to page 16). LCD Messages
In plumbed mode, if the water flow has been interrupted, LCD Screen will state “Water Flow Interrupted, To Reset, Please Press Brew Button”. Follow these instructions.
If the messages persist after following these instructions, contact Customer Service at 1.888.CUP.BREW (287.2739).

Chlorine or mineral taste in coffee| Consider using bottled water or filtered water. If you have any questions, contact Customer Service at 1.888.CUP.BREW (287.2739)
Brewing a partial cup|

The Exit Needle may be clogged (refer to page 16).
Clean the K-Cup® Pack Holder Assembly if necessary and rinse under faucet (refer to pages 15-16).
“De-Scale” the brewer (refer to pages 16-17).
If you have repeated the de-scale procedure on your brewer two times and it is still only brewing a partial cup, contact Customer Service at 1.888.CUP.BREW (287.2739).

The time is not displayed on the LCD Message Center|

The time will not be displayed on the LCD unless you have set it. To set the clock, follow the procedure on page 12.
If power is interrupted to the brewer, you will need to set the clock again using the procedure on page 12.

Brewer shuts off or turns on automatically|

Check to make sure that the Auto Off timer and/or On/Off time features have not been set. To do this, press the MENU Button below “MENU” and scroll through the programming options. “OFF” should be displayed for Auto Off timer and On/Off. If “OFF” is not displayed, follow directions on pages 13-14 to reset.

If any problems persist, contact Customer Service at 1.888.CUP.BREW (287.2739)

Warranty

Limited One Year Warranty

Keurig, Incorporated warrants that your brewer will be free of defects in materials or workmanship under normal use for one year from the date of purchase. It is recommended that you fill out and return the warranty card enclosed with your brewer so that your purchase information will be stored in our system. Keurig will, at its option, repair or replace a defective brewer without charge upon its receipt of proof of the date of purchase. If a replacement brewer is necessary to service this warranty, the replacement brewer may be new or reconditioned. If a replacement brewer is sent, a new limited one year warranty will be applied to the replacement brewer.

This warranty only applies to brewers operated in the United States and Canada. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state and, in the case of Canada, from province to province.

Only the use of Keurig Brewed® K-Cup® brand packs and accessories will guarantee the proper functioning and lifetime of your Keurig® brewer. Any damage to or malfunction of your brewer resulting from the use of non Keurig Brewed® K-Cup® brand packs and accessories may not be covered by this warranty or may result in a service fee if the damage or malfunction is determined to be caused by such use.

What is not covered by the Limited Warranty?

THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER INCIDENTAL COSTS AND EXPENSES RESULTING FROM ANY BREACH OF THIS WARRANTY, EVEN IF FORESEEABLE. Some states or provinces do not allow the exclusion or limitations of incidental or consequential damages, so the above limitation or exclusion may not apply to you depending on the state or province of purchase.

Nor does this warranty cover damages caused by use of non Keurig Brewed® K-Cup® brand packs or accessories, services performed by anyone other than Keurig or its authorized service providers, use of parts other than genuine Keurig® parts, or external causes such as abuse, misuse, inappropriate power supply or acts of God.

Other Limitations

THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS WARRANTY, WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO YOUR K150P BREWER, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Some states or provinces do not allow disclaimers of such implied warranties or limitations on how long an implied warranty lasts, so the above limitation may not apply to you depending on the state or the province of purchase.

How do you obtain warranty service?

Keurig® brewers are high-quality appliances and, with proper care, are intended to provide years of satisfying performance. However, should the need arise for warranty servicing, simply call Keurig Customer Service at our toll free phone number 1.888.CUP.BREW (287.2739). Please do not return your brewer for servicing without first speaking to Keurig Customer Service to obtain an Authorization to Return number (ATR). Keurig® brewers returned without an ATR number will be returned to the sender without servicing.

Keurig, Incorporated
55 Walkers Brook Drive
Reading, MA 01867
1.888.CUP.BREW (287.2739)

To learn more about Keurig, visit www.keurig.com or call 1.888.CUP.BREW (287.2739)

Keurig, Incorporated
55 Walkers Brook Drive
Reading, MA 01867
Keurig, Incorporated is a wholly-owned
subsidiary of Green Mountain Coffee Roasters, Inc.
Keurig, Incorporated est une filiale à 100 % de
Green Mountain Coffee Roasters, Inc.

Icons Icons
For Household and Commercial Use
Pour usage domestique et commercial
Pat./Brevets www.GMCR.com/patents