GGBOND G10 Mini RC Drone with Camera for Kids User Manual
- June 6, 2024
- GGBOND
Table of Contents
G10 Mini RC Drone with Camera for Kids
User Manual
(Suitable for wide indoor environments operation)
Suitable for 14 years old and above support@ggbondtoy.com
Package Contents
Charging
- When the drone’s battery is low, there are continuous beeps from the controller and the drone’s LEDs keep flashing.
- please use the original battery and USB cable provided.
- Keep the battery away from any sharp objects that could puncture the battery to avoid risks of explosion and fire.
- It’s not recommended to charge the battery from the USB port of the PC.
- Flight time may be reduced when flying in low-temperature environments.
Note: Please full charge the battery before flying.
Install
-
Open Up all 4 blades for the drone
This aircraft is of folding structure, please make sure to open all four blades before taking off. -
Blades Protector Installing
Expand the buckle of the protector, and install it onto the drone wings. -
Replace the propellers when it’s needed. (Optional)
1. Loosen the screws, then remove the cap.
2. Take out the propellers.
3. Fit the spare propellers into the drone according to the mark (NB) on them.
4. install the cap and tighten the screws.
Note:
Please do not overtighten the screws. Gently rotate the propellers by hand after installation to check if they are rotatable, if not, please loosen the screw and check again. -
Install the battery into the drone after it’s fully charged.
-
Install the controller batteries.
When the controller’s battery is low, there are continuous beeps from the remote and its LED indicator keeps flashing. -
Unfold the phone clamp to place your mobile device.
Remote Controller
1. Photo Speed Switch(short press)
2. Emergency Stop(long press)| 3.Video
4. 360° FIio
---|---
1. Phone Clamp
2. Left Control Stick
3. ON/OFF
4. One Key Take-off/Landing
5. Circle Fly
6. Headless Mode(short press)
One Key Return(long press)
7. High-speed Rotation| 8. LED Indicator
9. Right Control Stick
10. Drone’s LED Indicators ON/OFF
11. Forward Trim
12. Rightward Trim
13. Backward Trim
14. Leftward Trim
---|---
How To Fly
-
Switch On the Power
1. First power on the drone (Keep pressing for 2 seconds and place it on flat ground or surface.)
2. Press and hold the ON/OFF button to turn on the controller; you will hear a beep from the controller and its LED indicator starts flashing. -
Frequency matching
After turning on the drone, both indicator lights on the drone and controller will flash, then push the left throttle to the top, then down to the lowest, after 2 seconds, the indicators will go steady, which means the frequency- matched successfully. -
Compasses Calibration
Move both control sticks to the lower left at 45°; you’ll hear a beep from the remote. Calibration completes when the LEDs of the drone turn to solid on from flashing. -
Flight Instructions
Take-off
Option 1: Press the button to take off.
Option 2:
Simultaneously push the left Control Stick to lower left at 45° and the Right
Control Stick to lower right at 45° (or push the left Control Stick to lower
right at 45° and the Righi Control Stick to lower left at 45°) until the four
propellers start rotating, then slowly push the Left Control Stick forward to
take off.
Option 3
Throw-to-fly function
After frequency matching and calibration are finished, you can hold the
aircraft in your hand, and then horizontally throw it out. The aircraft will
automatically unlock the blades and fly in the air.
Note: It is better to operate the calibration step again after operating
Throw to fly for several limes. The function will be more stable.
Using the Remote Controller
Left Control Stick
| | Push the Left Control Stick forward, the drone will ascend; pull it
backward and the drone will descend.
---|---|---
| | Pull the Left Control Stick leftward, the drone will rotate to the left;
pull it rightward, the drone will rotate to the right.
Right Control Stick
| | Push the Right Control Stick forward, the drone will fly forward; pull it
backward, the drone will fly backward.
---|---|---
| | Pull the Right Control Stick leftward, the drone will fly leftward; pull
it rightward, the drone will fly rightward.
Flight Trimming
| | If the drone drifts forward or backward when hovering, press the Backward
Trim button or the Forward Trim button to adjust.
---|---|---
| | If the drone drifts leftward or rightward when hovering, press the
Rightward Trim button or the Leftward Trim button to adjust.
FLIGHT OPERATION GUIDE
IMPORTANT
- Make sure that you power on your drone first, and then the controller before each flight.
- Please repeat the pairing and calibration procedure each time while the drone or controller is restarted.
- For all flight functions and modes, the operator and tail of the drone must be aligned.
Aircraft Functions
Speed Switch
The drone is set to low speed by default.
Press the &DD button once for Medium **speed**
and there are two beeps from
the controller. Press it again for High speed and there are three beeps from
the controller.
Press it the third time to get back to Low speed and there is one beep from the controller.
Headless Mode
Short press the button to activate Headless Mode; LEDs on the drone start
flashing.
In this mode, the drone will fly following the direction of the Right Control
Stick regardless of the position of your drone’s head or tail.
Press the same button to exit this mode; LEDs on the drone turn to solid on.
360′ Flip
Fly the drone to a height over 2m, then press the **3D FLIP**
button to
activate 360° Flip function. Next, move the Right Control Stick to flip the
drone accordingly.
Note:
- There are continuous beeps from the remote when you activate this function. If you do not move the Right Control Stick about Ss after you press the
**3D FLIP**
button, the function will be canceled and the remote will stop beeping. - This function can’t be activated when the battery of the drone is low.
One Key Return
Press and hold the button, then the drone will fly toward its back following a
path parallel to its original take-off path. The LEDs on the drone keep
flashing when the drone is returning. Press and hold the button again or move
the Right Control Stick forward to cancel this mode, or the drone will keep
flying back.
High-Speed Rotation
Press the button to make the drone rotate at high speed. Press the button
again or move the Right Control Stick to any direction to exit this mode.
Note :
This function can’t be activated when the battery of the drone is low.
Circle Fly
In the case of barrier-free within a 5m radius around the drone, press the
button to fly the drone in a circle.
Press the button again or move the Right Control Stick in any direction to
exit this mode.
Note:
This function can’t be activated when the battery of the drone is low.
Photo / Video
Please connect the drone to your mobile device first, then go to the ‘Media’
in app Home Page or your album file of the device to check your photos and
videos.
Press the button to take a photo.
Press the button to start recording a video; press it again to stop recording and save the video.
Note:
It’s NOT recommended to use this function during normal flights for landing,
which may result in serious damage to your drone.
Altitude Hold/Hover
This is one of the default settings of the drone. When you release the Left
Control Stick after an ascent/descent action, the drone will hover at the
current flight height. For a stable flight, press the trim buttons to adjust
accordingly.
Emergency Stop
Press and hold the **SPEED**
button, then the drone will stop in the air and
fall.
Aircraft Parameters
Length of the main wing: | 83mm |
---|---|
Aircraft: | 98X120X33mm |
Total weight: | 54g±2g |
Battery: | 3.7V 380mAh |
Charging time: | About 50 mins |
Flight time: | 7-8 mins |
Gyroscope: | built-in |
Working temperature: | -10°C to 40°C |
Remote controller: | 2.4G |
Motor: | 7*16 4pcs |
Remote Controller Parameters
Wifi Transmission Range : | 30-40 meters |
---|
(in a wide open area with no electromagnetic interference)
Working frequency:| 2.4G
Battery:| 3xAAA
FAQ
| ISSUES| CAUSE| SUGGESTIONS
---|---|---|---
.1
‘| After the battery is inserted in the drone, indicator lights on the drone
keep flashing, no response to operations| Frequency matching between
controller and receiver is not successful.| Reoperate the frequency matching
for controller and drone (please refer to P.4 for details)
2| No response after is inserted battery rated in
the drone| 1. Check if the power for the controller and drone is fully
charged.
2. Connection of the poles are not good| 1. Open the remote battery case and
make sure the battery is inserted in the right position
2. Use a fully charged battery
3. Reinstall the battery and confirm whether it is of a good connection with
the poles.
3| Motor does not run when operating the throttle stick and the indicator
lights on the drone keep flashing| Power for the Li-Poly the battery is not
enough| Charge the battery or replace it with a full-charged battery
4| The main motor blades spin but the drone won’t fly| 1. Some of the blades
have been deformed
2. Battery power is not enough| 1. Replace the main blade
2. Charge the battery or replace it with a fully charged battery
Battery Using Attention
Matters needing attention
- Rechargeable batteries are to be removed from the toy before being charged.
- Non-rechargeable batteries are not to be recharged.
- Rechargeable batteries are only to be charged under adult supervision.
- Only used to charging 2S Li-ion or Li-polymer battery pack. if not, the charger or battery may be damaged.
- During charging, the charger should be put in a dry and ventilated place and far away from the heat source and inflammable and explosive substances.
- Never immediately charge your battery pack as soon as the flight is finished, or when its temperature doesn’t cool down. Otherwise, the battery will take a risk in swelling, even a fire.
- Ensure the correctness of polarity before connecting the battery to the charger.
- Avoid drop and violence during the process of charging. drop and violence will result in an internal short circuit of the battery.
- For the sake of safety, please use original charging equipment and battery pack. please change the new one in a time when the flying time is becoming shortened due to long time usage.
- If it is retained in the charger for a long time after saturation, the battery may automatically discharge. When the charger detects that the voltage of individual cells is lower than the rated voltage, it will re-charge until saturated. Frequently charging and discharging will shorten the lifetime of your battery pack. It is advised that please cut off the power and took off the battery after the charging is saturated.
Maintenance of battery pack
- The battery pack should be put in a dry and ventilated place. The storage temperature of the environment is ranged from 18°C to 25°C.
- Please avoid frequent charging and excessive discharging of the battery pack in order to prolong its life cycle.
- It is a must to maintain the battery pack before long-term storage. That is to charge the battery to the level of 50-60% saturation.
- If the storage term is over 1 month, it is advised to monthly check the voltage of every cell of the battery pack. The voltage of every cell should be not less than 3V. Otherwise, please refer to the above article (3)
- From the viewpoint of protection, a new battery pack should be motivated before usage.
That is to charge and discharge 3-5 times, but discharge is not less than the level of 70% saturation. This process will make the battery life longer and the voltage more stable.
SAFETY AND PRECAUTIONS
Remote-control models of quadcopters are dangerous merchandise. Their flight must be operated away from the crowd. Such factors as man-made improper assembly or mechanical damage, poor control of the electronic equipment, as well as unfamiliar manipulation may lead to unexpected flight accidents, such as uncontrolled flight and aircraft damage. Users are advised to pay attention to flight safety and understand that they are held responsible for any accident caused by negligence.
Special drones for Indoor and outdoor should stay away from barriers
This product is a remote-control drone, that is suitable for in indoor use and
outdoor environments (the outdoor wind power is less than Force 2). To fly
this drone, please choose appropriate obstacle-free indoor and outdoor sites
with proper distance kept from the crowd or pet animals. Please don’t operate
the product in any unsafe environments, such as places of heat, wires, power
supply, etc., so as to prevent the quadcopter from the risks of fire and
electric shock resulting from a collision, ditching, and entangling of the
drone.
Safe usage of the lithium battery
Lithium batteries are more dangerous than others. Be sure to read carefully
and follow the following precautions before using it. We will not be held
responsible for any damages caused by any improper use of the battery To avoid
the danger of explosion or fires, it is forbidden to use other chargers than
the one made by our factory. Such actions have done to the battery as impact,
dismantling, reverse connection of the positive and negative poles, and
burning are forbidden. Avoid metal objects from contacting the positive and
negative poles of the battery, which may cause a short circuit. Please prevent
sharp items from piercing the battery, and avoid the risk of battery fire.
Please be careful when charging the battery Make sure that the battery is
charging within your sight. Keep it out of the reach of young children so as
to avoid dangers. Don’t charge the battery when the battery is heated after
use. Otherwise, it may cause the battery to expand, change, explode or even
catch fire, threatening the safety of life and property. To dispose of the
battery, please recycle the battery in strict compliance with the waste
disposal laws and regulations of local countries or regions in order not to
pollute the environment
Away from moist environments
The interior of the aircraft is also composed of many sophisticated
electronic components so it must absolutely be kept away from moisture or
water vapor Don’t operate the aircraft in the bathroom or on rainy days;
otherwise, water vapor may get inside of the aircraft and cause mechanical
parts and electronic components to malfunction leading to expected accidents
Never misuse the product
Please do not disassemble or modify the product. For any upgrade, repair or
maintenance, please use the parts specified in our catalog to ensure the
safety of the structure. Please make sure the product is used within the
limits of operation. Don’t overload the product, and don’t use it in any other
illegal ways than prescribed by safety concerns and laws.
Safe usage of the battery
Batteries are to be inserted with the correct polarity. The supply terminals
are not to be short-circuited. Different types of batteries or new and used
batteries are not to be mixed. The exhausted batteries are to be removed from
the toy. For long time storage, please take them out to prevent battery
leakage. Please dispose of abandoned batteries in accordance to the laws and
regulations of the corresponding region to prevent pollution to the
environment.
Keep away from the source of heat
The aircraft is mostly made of PA fiber or polyethylene as well as other
main materials for electronic products. Therefore, it must be kept from the
source of heat and exposure to sunlight so as to avoid possible damage of
deformation or even meltdown due to high temperatures.
Never operate the product alone.
This product is suitable for users over 14 years old. Since the remote-
control quadcopter may pose a certain degree of difficulty for learners at the
beginning, it is recommended for it to be operated under the guidance of
experienced people for the sake of safe flight.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>