Uninet Infosystem Thingsocket Solutions TS-PTLS-2001 PTL Base Station User Manual
- June 6, 2024
- Uninet Infosystem Thingsocket Solutions
Table of Contents
Summary
Product Introduction
Base Station is the third-generation wireless base station. It is a new Active RFID fixed base station which implements bidirectional communication between the host system and the new ESL Tags. Century produces the base station for its electronic shelf label system (ESLs) and other products.
Dimensions and Weight
Dimensions: 140mm x 42mm
Weight: 250g (approx)
Unpacking and Checking **
**
In order to facilitate future storage and transportation, please keep the carton and packing materials after opening them. In addition to the base station, there is also included the following products and accessories:
| Item | Name | Qty | Comment |
|---|---|---|---|
| 1 | PTL Base Station | 1 | |
| 2 | Power Adapter | 1 | |
| 3 | Phillips pan head self-tapping screws | 4 | |
| 4 | Fitting | 1 | |
| 5 | Warranty card | 1 |
Features and Usage
Main Features: Wireless communication with ESL with easy installation,
operation of the labels, large signal coverage radius and supports many
labels.
Interface: TCP / IP connection with ESL server, 2.45GHz ISM with ESL labels.
LED: Blue – Power, Red – System, Yellow – Data Tx, Green – Data Rx. The TS-
PTLS-2001 maximum communication distance is 30-50 meters (Line of Sight and
open environment). Compared with base stations of similar nature the PTL bases
tation has an attractive appearance, ease of installation, and has good
structural design, with an IP53 protective environment rating. 1
Environmental Requirements
Temperature Range: -10°C to +55°C(14°F to +131°F)Humidity range: 20% to 95%Supply Voltage: AC/DC Adapter. Base Station Input Voltage 6VDC, 2.3A
Electronic Shelf Label System Overview
An electronic shelf label system (ESLs) consists of electronic shelf labels,
ESL servers, switches, base stations, Handset and software. The product
information in the database will be copied from the host computer to the
electronic shelf label system application software; then updated prices or
other information will be sent via Ethernet (or serial port) to the Base
Stations which will then deploy the update throughout the entire store via
2.4GHz wireless transmission Each part is described below:
ESL server: Running ESL System; Switch: For data exchange between the base
station and the server;Base Station: For data exchange between the ESL and the
Hub; Electronic Shelf Label: Updatable display for stored server information;
Handheld Reader: Used to bind labels to merchandise and for administration.
Technical Characteristics
Key Performance Areas
Uses 2.4GHz frequency within ISM band, worldwide compatibilityGreenTags proprietary wireless protocol to ensure data security supports Power over Ethernet (PoE) application Green Tags independent research to specifically support ESLThe ability to cascade Base Stations to reduce installation complexity and cost.
Electrical Characteristics
| Parameter | Specification |
|---|---|
| Power Supply | DC6V, 2.3A |
Supports 802.3af POE Power Supply
Standby Current| 650mA
Operating Current| 800mA
Network Interface| 10/100M Ethernet UDP Protocol
Expansion Interface| 10/100M Ethernet expansion port for a single Base Station
extension
IP Rating| IP53
RF Characteristics
| Parameter | Specification |
|---|---|
| Modulation | GFSK |
| Frequency | 2402-2482MHz |
| Antenna Gain | 2dBi |
| Receiver Sensitivity | -85dBm@0.1%BER |
| Antenna VSWR | ≤ 1.5:1 |
| Communication Distance | 15m to 50m |
Base Station Installation
Panel Description
| Label | Name | Use |
|---|---|---|
| RX | Receive Data LED | Lights when data from an ESL is received |
| TX | Send Data LED | Lights when Base Station sends data to ESL |
| SYS | System Status LED | Indicates normal System Status when flashing once per |
second
PWR| Power LED| Lights when Base Station Powered
DC6V| Power Port| 6VDC Power Connection (DC plug socket)
LAN| Network Port| Network cable into Base Station
EXT| Expansion Por| Port to connect one additional Base Station
Power Supply and Networking
As shown in the below figure the Base Stations can be powered in three ways:
| Method | Power Supply | Description | Connections |
|---|
Border
1| Power
Supply| When the switch does not provide power and external power is required|
Provide 6V to DC6V socket Connect Ethernet to LAN port
Border
2| POE| The switch provides power via Ethernet port| Connect PoE Ethernet to
LAN Port
Border
3| Cascade| Base Station provides power to next Base Station using PoE(do not
cascade more than one extra )| Connect PoE Switch to LAN Port and connect Base
Station to EXT Port on Second Base Station
Supply
Installation Conditions
Before Installation Check that the product is intact and all attachments are
complete, if there is damage or missing parts please contact Century romptly.
Check whether the following installation conditions exist before continuing:
A) Installation will meet applicable workplace standards.
B) Complete the required Installation processes.
Installation Location
The choice of Base Station position depends on its installation, it should be where possible, in a place free of obstacles that is safe and easy to operate. The Base Station can be mounted on the ceiling and or walls depending on
Installation Method
Before Installation: Configure all Base Station IP Addresses (refer software manual for instructions for this step). Installation: the Base Station secures with Phillips pan head self-tapping screws connect power cable and Network cable. Typical installation Figures 3-1 and 3-3
Figure 3-1 Base Station Arrangement
The Frame is the building outline, the view is from the top down with the view of all the Black dots (which are Base Stations) on the ceiling of the building; The Round dotted line circles are the Base Station signal coverage areas, typical coverage depending on the environment is between 15m to 50m in a simple open environment for a single Base Station.
Figure 3-3 Base Station Installation Distance
Figure 3-3 shows the inter Base Station installation distance, the dotted line represents the Base Station wireless signal coverage area; Ensure the istance betwen base stations is less than or equal to 20m.
Precautions
- The PTL Base Station power supply shipped has an input range of 100V to 240Vac 360mA please ensure it is able to be supplied with the correct voltage.
- Ensure that equipment is grounded.
- Check the Base Station and antenna installation position and orientation with respect to the ESL that will be exchanging data.
- This product radiates Radio Frequency (RF) energy, the installation, and commissioning personnel should leave at least 30cm between themselves and the antenna in order to meet the FCC requirements for human exposure.
- Any radio transmitting equipment, including this Base Station, can be interfered with by medical devices without proper protection. If there are problems seek the medical device manufacturer for advice.
- This equipment may cause interference with other electronic devices.
Troubleshooting
| Symptom | Cause | Troubleshooting | Comment |
|---|---|---|---|
| Power LED Does not light | Power Adapter may not work | Check Mains socket has | |
| power and is on, replace adapter if it does | |||
| Network Communication not normal | Interface Cable not connected or has | ||
| problem | Reconnect cable or replace if this still no response | ||
| Base StationIP configuration Problem may exist | Use the ESL Startup software | ||
| to configure Base Station IP Address |
Warranty
Thank you for purchasing Century product. The products you have purchased have
a limited warranty service during the given warranty period in which we will
provide the warranty services. The product warranty card is sent along with
the product, please t keep it safe, if the product needs warranty service,
please return it together with the warranty card to Century.
To learn more about our products or if you have any need or help, please visit
our website www.century-cn.com or contact us
directly, our contact details on the last page of this manual, we will be
happy to serve you.
Disclaimer:
This manual belongs to Hangzhou Century Co., Ltd (hereinafter referred to as
“Century”), it cannot be reproduced in part or whole without the express
permission of Century. Parties that do reproduce in part, or whole, this
document risk legal action.
Copyright:
Century reserves the right to modify the terms and specifications within this
document and has no obligations to notify any person of these modifications of
terms or specifications.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>