HOSiDEN HRM1095 Bluetooth Low Energy Module User Manual
- June 6, 2024
- HOSiDEN
Table of Contents
User Manual
HRM1095
HRM1095MAN001
Ver.0.50 Approved
| Author | Hiroki Hatsuda |
|---|---|
| Department | 2nd Engineering Dept. |
| Document Number | Shunji Muraoka |
| Version | HRM1095MAN001 |
| Status | 0.5 |
| Approved | |
| Approved | Checked |
| --- | --- |
Product Overview
Item| Specification|
Remark
---|---|---
Model Name| HRM1095| PMN: Bluetooth Low Energy Module
Frequency Range| From 2402 MHz to 2480 MHz.|
Operational Channel| 2402 + 2n MHz (n = 0,1,2…39)|
Data Rate| 1 Mbps and 2 Mbps|
Intended End Usage| Bluetooth® Low Energy Product|
Installation Method| Surface mount and reflow|
Operating Voltage| From 1.7V to 3.6V, 3.0V typ|
Applicable FCC rules| FCC Part 15 Subpart C|
Legal Statement
FCC Compliance/FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
The regulatory label on the final system must include the statement: “Contains
FCC ID: VIYHRM1095” or use the electronic labeling method as documented in KDB
784748.
The OEM integrators shall be responsible for testing and evaluation for any
additional compliance requirements required under regulations of each region
with their finished product that is installed in this module. (for example
EMC, safety, etc)
The OEM integrators must select either DC / DC regulator or LDO regulator from
the product’s internal power supply by the software.
The modular transmitter is only FCC authorized for the specific rule parts
(i.e., FCC transmitter rules) listed on the grant, and the host product
manufacturer is responsible for compliance to any other FCC rules that apply
to the host not covered by the modular transmitter grant of certification.
The final host product still requires Part 15 Subpart B compliance testing
with the modular transmitter installed.
The manual for the final product with this product should state the
following:
“This transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter.” “This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment and meets the FCC
radio frequency (RF) Exposure Guidelines as this equipment has very low levels
of RF energy.” The device is designed to use an integrated antenna. Do not
modify the antenna or any other part of the module. Any modifications will
invalidate the modular certifications and require new approvals for the host
system.
In case a conflict arises between Japanese and English versions, the English
version takes priority.
Industry Canada Compliance
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions: (1) This device
may not cause interference. (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
The regulatory label on the final system must include the statement: “Contains
IC: 7305A-HRM1095”
The OEM integrators shall be responsible for testing and evaluation for any
additional compliance requirements required under regulations of each region
with their finished product that is installed in this module. (for example:
EMC, safety, etc)
The OEM integrators must select either DC/DC regulator or LDO regulator from
the product’s internal power supply by the software.
The manual for the final product with this product should state the
following:
「 This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment and meets RSS-102 of the ISED radio frequency (RF)
Exposure rules as this equipment has very low levels of RF energy. 」
In case a conflict arises between Japanese, English, and French versions, the
English version takes priority.
Antenna List
Model Nama
| Frequency Range| Antenna Type|
Antenna Gain
---|---|---|---
HRM1095-010020| From 2402 MHz to 2480 MHz.| 1/4λ inverted F antenna| -0.8 dBi
Change History
Version| Issue Date| Status| Author|
Purpose
---|---|---|---|---
0.10| 2021 July 30| Draft| Hiroki Hatsuda| First draft.
0.20| 2021 Sep 17| Draft| Tomoki Umeda| Legal Statement update
0.30| 2021 Sep 30| Draft| Tomoki Umeda| Legal Statement and antenna list
update
0.40| 2021 Oct 4| Draft| Tomoki Umeda| Legal Statement update
0.50| 2021 Oct 6| Approved| Tomoki Umeda| Change to Approved
End of Document
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>