Shenzhen Jianyi Keji Youxian Gongsi BHF02 Bluetooth Headset User Manual
- June 6, 2024
- Shenzhen Jianyi Keji Youxian Gongsi
Table of Contents
BHF02
User Manual
Power on: In shut-down state, long-press the Multi-Function Button ( MFB)
for about 3 seconds, the headphone is turned on with a prompt tone and blue
light flashes 5 times quickly
Pairing: Long press MFB around 5s to Power on with prompt tone, the blue
light flashes 5 times quickly then blue and red light flash alternately, and
the headphone enters the pairing mode with a prompt tone. Then operate the
cellphone to pair with it.
Re-connecting
- Long press MFB around 3s to power on and it will enter the re-connection mode with blue light flas h once every 5s, And re-connected with the paired device in priority. by double-clicking the MFB to skip to pairing mode if needed. But the paired device needs to be re-connected manually under pairing mode
- The headphone will enter re-connection mode after back to effective working distance If disconnected because of over distance
Power off: In power-on state, long press MFB about 3s with red light
flashes 5 times quickly and with a prompt tone
Answer phone calls: In Bluetooth Connected state, there is an incoming
call, short press the MFB to pick up the call with a prompt tone.
End up Phone calls: During calling state, short press MFB to end up the
calls with a prompt tone
Reject phone calls: for unwanted phone calling, long press MFB for about
2 seconds to reject with a prompt tone.
Volume Adjustment: In phone calling or music playing status, short press
the button “+” for volume up; short press “-” for volume down .there is prompt
tones when the volume is at the maximum and minimum.
The Last Number Redial: In the standby state double-click MFB to redial
the last number that has been called before with a prompt tone.
Activating SIRI: In the standby state, long press MFB for about 1.5
seconds to start SIRI (if The cellphone Bluetooth support this function) with
a prompt tone.
Voice transfer: During phone calls, long press the button “+” for about 3
seconds, there is a “Toot” sound, then the voice is transferred to the
cellphone. The same operation to transfer voice back to the headphone again
with a prompt tone
Phone Call Mute: During the phone call, press the mute button about 1s to
turn off the MIC. The same operation to turn on the MIC, both with prompt
tone.
Music Play/Pause: Short press the MFB to play/pause music.
Previous/Next song: Long press “-” button about 2 seconds to previous
song, long press “+” button about 2 seconds to next song.
Removing pairing: after powered-on, long-press the MFB firstly then long
press “-” button about 5 seconds immediately, there is a prompt tone. Then
paired memories are removed and enter pairing mode automatically
LED Indicator status
| Power-on and Pairing: | Blue light flashes 5 times |
|---|---|
| Power off: | Red light flashes 5 times |
| Pairing status: | Red and blue lights flash alternately |
| Standby status: | Blue light flashes once every 4 seconds |
| Incoming call: | Blue light flashes once every 2 seconds |
| During phone calling: | Blue light flashes once every 7 seconds |
| Music playing status : | Blue light flashes once every 8 seconds |
| Charging process: | The red light is always on |
| Charging completed: | Red light off |
| Low battery reminder: | Red light flashes twice every 12 seconds and there is a |
“Toot” sound every 60 seconds
Reconnect mode:| Blue light flashes once times every 5 seconds
Charging Operation
- Charge at charging Dock: Connect the charging dock with a 5V power source with its red light always on. And put the headphone at the dock then charging starts with the red light of headphones on. When fully charged the red light of the headphones will be off. the headphone is workable during the charging process
- The headphone can be charged directly by Type-c cord
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
– Reorient the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help. Changes
or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>