ViC FiRTH VXHP0012 Bluetooth Isolation Headphones User Guide
- June 6, 2024
- ViC FiRTH
Table of Contents
ViC FiRTH VXHP0012 Bluetooth Isolation Headphones
POWER ON:
Press and hold the on/off button for 3 seconds until the blue LED flashes and
you hear “Power On.”
POWER OFF:
Press and hold the on/off button for 3 seconds till Red LED flashes and you
hear “Power Off.” Headphones will automatically power off if there is no music
input for 3 minutes.
LOW BATTERY:
Recharge the headset when you hear “Low Battery” every 2 minutes, or the red
light flashes
every 5 seconds.
FIRST TIME PAIRING:
The Bluetooth® headset will enter pairing mode automatically after the power
is switched on. The red & blue LED light will flash alternatively. Turn on the
Bluetooth® function on your music device and pair with the headset. Pairing is
successful when you hear “Connected” and the blue LED light flashes every 5
seconds.
RE-PAIRING:
For devices that have already been paired, the headset will automatically
reconnect when the power is turned on, or you can select “Vic Firth
Headphones” on the device to re-connect.
WIRED USAGE:
A 3.5mm line-in cable is provided to enable optional use as wired headphones.
Simply plug the line-in cable into the line-in jack on the [left/right] earcup
and plug into your desired device.
OPERATION BUTTONS GUIDE:
ANSWER PHONE CALL: Press On/Off button once END PHONE CALL: Press On/Off button once
VOLUME UP: Press once PREVIOUS TRACK: Press and hold for 2 seconds
VOLUME DOWN: Press onceNEXT TRACK: Press and hold for 2 seconds
LED INDICATOR :
LOW BATTERY:
Red light flash every 5 seconds
CHARGING:
Red light on (connect USB cord to USB socket)
BATTERY FULL:
Red light off
HEADPHONES IN OPERATION:
Blue light flashes every 5 seconds
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation. FCC ID:2A2KDVXHP0012
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference
that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note:This equipment has been tested and found to comply with the limits for a
class B digital device,pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequence energy and,if not installed and used in accordance with the
instructions,may cause harmful interference to radio
communications.However,there is no guarantee that interference will not occur
in a particular installation.if this equipmemt does cause harmful interference
to radio or television reception,which can be determined by turning the
equipment off and on,the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an autlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The devicecan be used in portable exposure condition without restriction.
CONTACT US:
For questions, contact us at zcustomercare@zildjian.com or visit our website at www.vicfirth.com.
CONTENTS: 1 pair of headphones, 150cm detachable 3.5mm line-in cable,
40cm USB charging cable, 6.3mm headphone jack adapter, 1 instruction insert
WARNING:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules.These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Device contains batteries. Do not dispose of batteries in fire. Do not mix
this battery with the solid waste stream. Dispose of according to local
regulations.
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Vic Firt h Company is under
license. Other trademarks and trade names are those of their respective
owners.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>