Shenzhen Shenan Yangguang Electronics FS03D Motion-Activated Alert User Manual

Solar Wireless Driveway
And Intruder Alert
User Manual
Please read this user maul before using and installation

 Welcome

Thank you for purchasing our product
This wireless driveway and intruder alert has an 850 feet (200M’) range.
It is great for multiple applications, including:

• Alerting you when visitors enter your driveway
• Deterring trespassers and thieves from entering your property or building
• Alerting you to wildlife on your land
• Using in drive-thrus to signal that a customer has pulled in ad more

Our wireless doorbell is expandable which allows you to pair various transmitters to the receiver such as contact sensor motion detector pet push etc
One doorbell receiver can pair with up to 50 various transmitters and each transmitter can be set to a different ringtone

Features

• Passive Infrared (PI) Sensor & Receiver

• Wireless RF Transmission Up to 650 feet

• Sensor Detects Motion and riggers the Receiver to Turn on a Chime

• Sensor Detection Range up to 13 Feet (mounted at 50′ height)

• Sensor Detection Angle.30 degrees up and down,60 degrees left, and night

• 5Levels of Sound Vo/um sensor (mute mode)
  But-in 4 2V/15004A 18650 hum battery, support solar charging

• Receiver-AC100-240V Operation

• Battery Low Indicator LED for Sensor

• Trigger LED on Sensor

• Wireless, Easy Installation

• water Resistant Sensor

How Does It Work?

Basically, there are three parts to the Driveway Alert system

1. The indoor Alarm Receiver works as an alarm buzzer and8 door chime. It monitors for signals coming from the Passive Infrared (PIR) Motion Sensors and the Doorbell and activates an alert in response to that signal It also features an LED indicator so you can visually tell when an alert is coming to The Indoor Alarm Receiver can be simply plugged into an AC outlet
2. The IRttotion Sensors enable you to detect the movement of people and vehicles while allowing small animals to pass through undetected.it will send a signal to the Indoor  Alarm Receiver whenever motion is detected The motion sensors should be deployed outdoors, where there is a clear view of the driveway or the likely entry and exit paths that you plan to secure
3. The Doorbell Push enables visitors to send a chime to the Indoor Alarm Receiver so you know that someone’s waiting at your doorstep. As it is either water or weatherproof, it must be installed in a sheltered location

Overview

PIR motion sensor

You can pair up to 50 sensors & push buttons to your receiver and each sensor can have its own unique meld

Indoor Chime Receiver
The receiver has up to 58 melodies for you to choose from You can also have multiple receivers in different locations in your home or business, S0 you can hear the alarm chimes

Getting Started

1. POWERING THE INDOOR CHIME RECEIVER
   Plug the receiver into the outlet. The receiver will perform better if kept away from other electrical equipment (eg TV, microwave

2. POWERING THE PIR MOTION SENSOR
   The motion sensor runs on4 a 2V/ 20004A 18650 lithium battery and operates wireless/y at a maximum distance from the receiver of 850feet (200m.)

3. SOUND VOLUME CONTROL.
   Press the volume control button on the receiver to cycle through 5 volume levels

4. SETTING RINGTONE FOR A TRANSMITTER
   There are 58 melodies to choose from
   (1) Press the Forward Button or Back Button to choose your favorite ringtone
   (2) Please follow the pairing steps below to sync the new ringtone. The new ringtone will be set for the most recently synced transmitter

5. PAIRING A TRANSMITTER TO THE RECEIVER**** (1) Remove the screws from the four corners of the back of the motion sensor to access the battery compartment

(2) Take off the back cover and turn on the battery switch, when you see the pr sensor flash, then you can replace the back cover and secure the screws to wait for Piaf

(3) Please select your favorite ringtone before pairing

(4) Press the volume control button for S seconds until a Dingdong is heard and the LED the indicator starts floating-you are now in pairing mode

(5)Active the transmitter to send a signal to the receiver

6. TWO OR MORE TRANSMITTERS PAIRING
   The pairing mode is required for each transmitter. For two or more transmitters, please follow the pairing step8(1)-(3)for each transmitter

7. RESET
   Press Forward Button for seconds to reset receivers to default When the receiver sounds Ding Dong’ with LED flashing that means the reset was successful After a reset receivers revert back to the 1stringtone and transmitters must be paired again.

Please note:
(1). Pairing mode will last for seconds only before timing out. Ensure you activate the transmitter during this time or the process will have to start again.
(2) Pairing mode will quit automatically after pairing is completed.

Installing the PIR motion sensor

We recommend mounting the motion sensor at least 3to4f(1m) above the ground on a sturdy, n-metal surface (i.e.a wall wooden post or tree) with the sensor eye pointed straight out over the area you wish to cover (such as up your driveway looking towards your house)
This will decrease or eliminate false alarms from small animals, give you a longer area to pick up movement, and avoid unwanted alarms from nearby lawns/roads

Note:
Always test that your sensor is working in your desired location before installing it. Avoid placing your sensor in a location where sunlight will shine directly into the sensory. Direct sunlight may cause false alarms and/or damage to th6 p1sensor

Tools you will need for installation

• pencil
• Phillips screwdriver
• Electric drill with 3/32“ and 7/32 drill bits (recommended)
• Hammer (optional)

(1). Mark the mounting holes with a pencil
(2). If installing on a wooden surface, you only need to use the included screws. Drill out your pilot holes using a ¾ drill bit to a depth of This will help prevent stripping of the screws and hold the sensor more securely

(3). If installing on any other surface, such as brick or masonry, you will use the included screws and anchors. Drill out your pilot holes using8 7/32 ell bit to a depth of1 Gently  tap the anchors in your pilot holes using charmer until the anchors are flush with the mounting surface
(4). Screw the bracket base to the place you want to install
(5). Screw the back cover onto the shaft of the bracket
(6) Replace the back cover and secure the screws
(7). Twist the ball onto the fed base of the bracket just until tight Do not over-tighten
(8). Adjust the angle of your sensor so that it is looking at your target area

FCC Caution：

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>