ELIZ EWH 201 Air Heater Instruction Manual

ELIZ EWH 201 Air Heater

Read these instructions carefully before installing and using the product!
It is necessary to comply with the requirements and recommendations set out therein. Observance of the rules of these instructions is part of the measure for the safe use of the product, as well as one of the conditions for the warranty recognition.
The product has an international CE certificate and complies with technical standards according to EN.

The product meets all the basic requirements:

• Electromagnetic compatibility directive (EMC)
• Low voltage direction (LVD)

Children under 3 years of age should be kept away from the appliance unless they are under constant supervision.
Children from 3 to 8 years of age must not: connect the plug to power sockets, make adjustments, clean it or carry out user maintenance operations.
Children between the age of 3 and 8 may only switch the appliance on/off provided that it has been set up and installed in the normal operating position and they are under supervision, or have been instructed how to operate the appliance safely and understand the hazards associated with use.

This appliance can be used by children older than 8 years of age and by people with reduced physical, sensor and mental capabilities, as well as by people with insufficient experience and knowledge provided they are supervised or instructed in safe operation of the appliance and understand the related risks. Children should not be allowed to play with the appliance!

WARNING! Some parts of this product can become very hot and cause burns. Special attention should be paid when there are children and vulnerable people.
WARNING! In order to avoid overheating and fire, do not cover the appliance!

IMPORTANT SAFETY INSTRUCTIONS

• Before connecting the appliance, make sure that the voltage in your household is the same as is indicated on the product rating label. Connect the appliance only to a single-phase power socket that complies with the information on the rating label.
• Make sure the appliance is switched off before connecting it to the power supply.
• The product is intended exclusively for use as a domestic heater. It is not intended as the main heater. Use it only as an additional heater.
• Use for purposes other than domestic use can be dangerous!
• The heater is not suitable for outdoor and commercial use and is not intended for animal breeding! The manufacturer is not liable for malfunctions resulting from improper use.
• Do not block the air inlet and outlet of the heater to ensure proper air circulation.
• Never use the heater in rooms where gas, solvents, varnishes, adhesives, and other highly flammable substances are used or stored.
• The heater must always be placed on a non-flammable, flat, and stable surface. Use the heater always only in a horizontal position on a vertical wall at a height of min. 1.8 meters from the floor. Avoid installing the heater behind the door.
• Never place the product on a bed or carpet!
• Do not place the device near flammable materials. There is a risk of fire. The minimum distance between the heater and flammable materials such as furniture, bedding, paper, clothing, curtains, and the like must be at least 1 m!
• When operating the heater, some parts may be hot, therefore, be careful not to touch the heater.
• Do not use the heater near a bath, shower, washbasin, or swimming pool (minimum distance is 1 meter). There is a risk of electric shock.
• Never touch the heater with wet or damp hands, there is a risk of electric shock.
• Do not touch an appliance that has fallen into the water.
• Do not allow children or animals to touch or play with the heater.
• Keep the power cord away from hot parts of the device.
• Place the power cord so that it does not impede the free movement of persons and no one trips over it.
• Do not insert fingers or any other objects through the heater grille when the appliance is connected to the power supply – there is a risk of electric shock, fire, or damage to the unit.
• Never use the heater if the power cord is damaged.
• If the power cord is damaged, stop using the heater and contact an authorized service center. To avoid a hazard, it may only be replaced by the manufacturer, a service center, or a similarly qualified person!
• If the heater is damaged or does not work, turn it off and do not manipulate it. In the event of a fault, do not disassemble the product. Contact your dealer or central service center. Never repair the heater yourself. Otherwise, the safety of the appliance may be endangered.
• Never switch off the heater by pulling the power cord!
• Do not bend the power cord or pull it over sharp edges, do not place it above another heating source or an open fire!
• The most common cause of overheating is the accumulation of dust or down in the appliance. Clean the air inlet and outlet regularly with a vacuum cleaner. Before cleaning or performing maintenance, turn off the heater and unplug the power cord.
• Do not leave the device switched on unnecessarily. If you do not intend to use it or you leave home, turn it off and unplug the power cord. Do not leave the heater unattended during operation. There is a risk of fire.
• Do not place the heater on or near another heating sources.
• Do not use this heater with a programming unit, timer, stand-alone remote control system, or any other device that automatically switches on the heater, because there is a risk of overheating and a risk of fire if the heater is covered or incorrectly positioned.
• Never place the heater directly above the power socket. Hot air can damage the power cord and socket.
• If the heater falls from the wall, disconnect the power supply and wait until the heater cools down! Do not touch the fallen heater, there is a burn hazard!
• Do not use the product in a dusty environ-ment!
• Do not use the extension cord to connect the device to the power supply. There is a risk of overheating and fire.
• Do not use the heater to dry laundry!

PACKAGING

• After unpacking the product, please check that the packaging is complete and that the product has not been damaged during transport! If you find any damage or incomplete packaging, contact an authorized dealer!
• Do not throw away the original packaging! It can be used for storage and transport purposes to prevent damage during transport!
• Disposal of packaging materials should be done accordingly. Keep packaging materials such as bags and staples out of the reach of children!

PACKAGE CONTENTS

• 1 x EWH 201 heater
• 1 x remote control (battery included)
• 1 x set of screws and dowels (2 pcs)
• 1 x user manual

TECHNICAL DATA – DESCRIPTION

ELIZ EWH 201 is a wall-mounted electric PTC heater designed for space heating, with electronic control, weekly timer, and open window detection.

Heater description – for Fig.1

1. Cold air inlet grille
2. Transparent LED display
3. Start / Stop button
4. Power switch
5. Power cord
6. Mounting / hanging holes
7. Hot air outlet
8. Remote control
9. Screws and dowels

DISPLAY DESCRIPTION
Temperature display

Indicator:   lights up when the Temperature setting mode, – flashes when the Open window detection

ELECTRICAL CONNECTION

Power supply: ~ 220 – 240 V, 50-60 Hz ; Fuse: 10 A
The electrical installation, as well as the connection, must be carried out under the applicable regulations and standards. The heater includes a flexible power cord with a 230 V plug. Plug the power cord into a socket with ground contact. Do not place the heater directly below or above a power socket.

HEATER LOCATION

• Place the heater on a flat wall and only in a horizontal position! It is necessary to mount the heater at least 180 cm above the floor. Keep the minimum distances among the heater, the ceiling, and the surrounding walls – the minimum distance must be kept! – see Fig. 2.
• Do not place the device in a vertical or leaning position. The device must not be mounted on the ceiling!
• The minimum distance of objects from the heater should be at least 1 meter – see the Fig. 2.

Wall mounting:

• Drill two holes in the wall at least 180 cm above floor level, 315 mm apart.
• Make sure that the diameter of the holes is the same as dowels with a diameter of 6 mm.
• Insert the dowels into the holes and drive the screws into the dowels so that the screw heads protrude approximately 10 – 15 mm from the wall. Screws and dowels are included in the package.
• Attach the heater with holes „A“ to the wall on the screws, move it slightly to the right, and then down to point „B“.
• The heater is installed, make sure that the device is stably mounted!

OPERATION

• Before connecting and switching on the heater, make sure that the socket has the protection of at least 10 A.
• The device is controlled by the included remote control (or using the buttons on the front panel).
• At the bottom of the remote control remove the battery foil, which protects it from discharge.
• Plug the heater into an AC ~ 220-240 V, 50-60 Hz power socket and turn the power switch to the position I.
• When the power switch is turned on, the heater beeps and enters standby mode. The display shows the current room temperature in °C.

General use:

• The device is turned on and off by pressing on the remote control or Start/Stop on the back of the heater.
• When the button is pressed for the first time, the heater will turn on and start operating in fan mode – only cold air will blow. The fan indicator light is on.
• The button is used to select the heating output level LOW / HIGH, or the fan without heating
  • press the button once, the heating with a power of 1 000 W is switched on – indicator light is on – .
  • press the button twice, the heating with the full power of 2 000 W is switched on – indicator light is on – .
  • pressing the button again will turn off the heating and the heater will operate in fan mode again.

WARNING: We do not recommend using the LOW and HIGH heating modes separately, as the heater will heat up to a maximum temperature of 51 °C. It is necessary to switch the heater to the Temperature setting mode or the Weekly program mode.

HEATING MODE SETTING
The heater can be used in 2 heating modes – Temperature setting mode and Weekly program mode.
Temperature setting mode (with Off timer up to 8 hours)
in this mode, the set temperature is automatically regulated and kept at a constant level by the thermostat according to the set temperature (see Temperature setting) until you switch off the heater. It allows you to set the heating off timer for up to 8 hours.

Weekly program
in this mode, the heater works and heats the air only in periods according to the selected weekly timer program.
The set temperature in the room will be automatically regulated and kept at a constant level by the thermostat only during the time intervals of the selected timer program.

TEMPERATURE SETTING MODE

• To turn on this mode, press the button . Using the buttons + / – you can set the desired temperature in the range of 18 – 45 °C, displayed on the heater by flashing numbers. Confirm the temperature setting by pressing the OK button, or it will be confirmed automatically after 5 seconds. The default temperature is 25 °C.
• If the set temperature is equal to or lower than the room temperature, heating does not take place.
• If the temperature drops below the set temperature by 1 °C, the thermostat switches on the heating as follows:
  • If the set temperature is 1-2 °C higher than the room temperature, the power 1 000 W is switched on –
  • If the set temperature is higher by 3 °C or more, the full power of 2 000 W is switched on –
  • As soon as the room temperature reaches the set value, the heating is switched off, but the fan function remains in operation.

Setting the Off timer
Working only in Temperature setting mode and fan mode. Using the button on the remote control, you can set a timer – the remaining operating time of the heater up to a total of 8 hours in steps of 1 hour shown on the display. The setting is automatically confirmed after 5 seconds. The heater switches off automatically when the set time has elapsed. Turning off the device before the remaining time has elapsed clears the timer setting.

WEEKLY TIMER PROGRAM

The weekly timer program can only be switched on in heating modes (LOW or HIGH), or Temperature setting mode. Not when the heater is in a Fan mode.

The mode is switched on by pressing the button on the remote control. When switching on this mode for the first time (or in the event of a power supply failure), it is necessary to set the current day of the week and time!

Turning on the mode and setting the time
Press the , the display shows the day 01 (ie Monday). Use + / – buttons to set the current day from 1 to 7 (Monday – Sunday). Confirm by pressing the OK button and continue with the time setting. The display shows time 00, ie. 0 hours. Use the + / – buttons to set the current time in hours from 1 to 23. Confirm by pressing OK and continue with the time setting in minutes. The display shows time 00, ie. 0 minutes. Use the + / – buttons to set the current time in minutes from 1 to 59. Confirm by pressing OK. The display shows P1 symbol – timer program P1.

If you want to keep the set program P1, press the OK button. The weekly program indicator light is on
If you do not press the OK button within 10 seconds, the time setting is invalid. To reset the time, first, turn off the heater with the power switch, then turn it on and follow the procedure above.

Changing the weekly program
If you want to change the program setting from P1 to another, press the button until the desired program
P1 – P6 is selected (description below). Confirm the program by pressing OK. After confirming the program, the indicator will be on or flash depending on the program and the current time. If you do not press the OK within 10 seconds, the program setting is invalid. If you press the button 7 times, you will deactivate the Weekly program.

If the heating mode LOW or HIGH is working when activating (switching on) the Weekly program, the heater will continue in heating at the selected stage. However, heating will take place up to the maximum temperature, therefore switching on the Weekly program in heating modes LOW or HIGH is not recommended!

Activation of the Weekly program is recommended in Temperature setting mode!
First switch on the Temperature setting mode and set the desired temperature (see Temperature setting mode), and then switch on the Weekly program so that the heater only heats up to the set temperature in the Weekly program. The display shows the room temperature, the indicator lights and will light on.

OFF
P4| 18:00 – 7:00| 18:00 – 7:00| 18:00 – 7:00| 18:00 – 7:00| 18:00 – 7:00| OFF| OFF
P5| OFF| OFF| OFF| OFF| OFF| 00:00 – 23:59| 00:00 – 23:59
P6| custom setting| custom setting| custom setting| custom setting| custom setting| custom setting| custom setting
Note:| P2 / P4 mode – switching off is the next morning

P6 – time setting range is 0-24 hours. Starting time must be set before ending time, otherwise, the setting is invalid.

P6 program setting – custom timer setting
In the P6 program, you can set only 1 time period per day (on-off), the time is set only in hours. Press the button
to select program P6 and confirm with the OK button. If you do not press the OK button within 10 seconds, the program setting is invalid. The display shows day 1 (Monday), using the + / – buttons you can select the day from 1 to 7 (Monday-Sunday) for which you want to set the period.

Setting for day 1 – Monday
The display shows 1 and flashes. Press OK, the display shows the time 00 – the beginning of the period. Use the + / – buttons to set the starting time 0 – 24 hours, then press OK, the heating starting time setting is completed. The display shows the ending time of period 00. Use the + / – buttons to set the ending time 0 – 24 hours, then press OK, the heating ending time setting is completed. The heater switches the heating on and off only on the selected day and the set period, e.g. 7 a.m. – 3 p.m.
If the period 00 – 00 is set, the heater will not work on that day. If you do not press OK while the day selection (1) is flashing, the setting will automatically move to the next day (2) after 5 seconds, the time 00-00 will be set for day 1.
The program setting for days 2-7 (Tuesday – Sunday) is the same as for day 1.

Note: It is necessary to set the starting time and the ending time of the heating! The setting must be completed for all days 1-7 (custom period or time 00:00). When the custom setting for day 7 is completed, the P6 Weekly program will start and the indicator will be on.

CANCELING THE WEEKLY PROGRAM

1. Press during program setting
2. If the setting has already been completed, press first and then .

If the Weekly program has been switched on in Temperature setting mode, after canceling it, the heater will return to Temperature setting mode. (If the Weekly program has been switched on in LOW or HIGH heating modes, after canceling it, the heater will continue in the selected LOW / HIGH heating mode).

CANCELING THE TEMPERATURE SETTING MODE
Press during program setting. 2. If the setting has already been completed, press first and then .
When the mode is canceled, the heater switches to fan mode. 3. Press , the heater switches to heating mode.

OPEN WINDOW DETECTION

This function can be activated in all heating modes except fan mode.

Press the button to turn detection on or off. When the detection is switched on, the indicator flashes. Temperature detection starts 1 minute after switching on (temperature detection checkpoint is created). If the heater electronic control detect an open window and a sharp drop in the ambient temperature of 8 °C within 10 minutes – (one round, temperature detection once every 5 minutes), the heater automatically stops heating.

Description of the function/time intervals of one detection round:

• 0:00 – Open window detection activation
• 1:00 – Starting temperature detection, start of the round. A temperature detection start checkpoint is created.
• 6:00 – Temperature detection checkpoint 1 – temperature fast down detection check point
  • Temperature detection check point 1 reduce from Temperature detection starting checkpoint is ≤ 8 °C – the heater continues to heat, open window detection remains active.
  • Temperature detection check point 1 reduce from Temperature detection starting checkpoint is > 8°C – the heater switches off the heating and turns into standby mode, open window detection is switched off – see Notes.
  • The measured temperature is higher than Temperature detection start checkpoint – the heater continues to heat, open window detection remains active. (Maximum detection temperature is 51 °C – Overheat protection)
• 11:00 – Temperature detection checkpoint 2 – temperature slow down detection check point
  • The temperature measured at this point is the end of the first round and the beginning of the second round of measurement. For 10 minutes as one round, the temperature is measured every 5 minutes. At this point, the temperature detection method is the same as in detection point no. 1.

Notes on Open window detection:
If the heater detects a drop in temperature and switches off the heating, the alarm is activated for 5 seconds, OF is on and the entire display flashes. The heater works for another 30 s in fan mode and then switches off to standby mode. To restore the function to the original mode, press before switching off. When the Open window detection mode is restored, a new round of detection will start.

SWITCHING OFF THE HEATER
To switch off the heater, press the button. The display will start counting down the time of 30 seconds during which the heater will work as a fan, then it switches to standby mode. The current room temperature remains on the display. To switch off the device completely, disconnect the power cord from the socket!
Warning: During the first use and heating, there is a firing of the heating element. It is just a temporary phenomenon that stops after a few minutes. Ventilate the room and continue heating.

OVERHEATING PROTECTION
The heater has a built-in fuse that automatically switches off the heater when overheated (at 51 °C). In this case, unplug the heater and let it cool down. Check that the air inlet and outlet are not blocked. After cooling down, switch on the heater again. If the heater still does not work, contact an authorized service center.

STORAGE

• Before storing the heater, unplug it and let it cool down!
• If you will not be using the heater for a long time, store it in its original packaging or bag. It will be protected from the concentration of dust and dirt.
• The product must be stored in a dry place, out of direct sunlight.
• It is expressly forbidden to store the device in humid or wet areas.

CLEANING AND MAINTENANCE

The device does not require special maintenance. Routine surface cleaning is recommended.

• The heater can only be cleaned when it is switched off and when it has cooled down!
• Before cleaning, turn off the heater, unplug the power cord, and let the heater cool down.
• The surface can be cleaned with a damp cloth, vacuum cleaner, or soft brush.
• Never immerse the heater or power cord in water – there is a risk of electric shock!
• Never clean it with acids, chemical thinner, gasoline, abrasive cleaners, etc.!

WARRANTY TERMS AND CONDITIONS, WARRANTY SERVICE

By following the instructions for installation, operation, and maintenance, the manufacturer guarantees that the product will have the properties specified by the relevant technical conditions and standards throughout the warranty period.
The product is guaranteed for 2 years from the date of sale stated on the proof of purchase.

Warranty conditions:

1. Proof of purchase required.
2. The condition and functionality of the product are not disturbed by violent and unprofessional interventions of the user or by a natural disaster.
3. Installation and operation have been performed according to the instructions in user manual.

The warranty expires in the following cases:

• Damage to the product during transport of goods
• Improper use and storage
• Using a power supply with a higher voltage than indicated on the rating label
• Natural disasters or other circumstances
• Failure to follow the instructions
• In case of repair or attempt to repair the device by an unauthorized person
• Any intervention in the construction of the heater, its modification, or change.

If a malfunction occurs during the warranty period that was not caused by the user or a natural disaster, contact an authorized service center to verify the repair. After a justified claim, the service center will repair the product free of charge.

WARNING!

• In the event of failure to submit the necessary documents (proof of purchase), damage to the product by the user, or failure to follow the instructions for installation, operation, and maintenance, the service center will repair the product only at the user‘s expense.
• Discharging the battery of the remote control cannot be recognized as a product defect under warranty!
• Any intervention in the interior part of the product is prohibited. Repairs and related activities may only be performed by an authorized service center!
  The manufacturer reserves the right to make design changes without prior notice, as long as such change does not affect the functional properties and safety of the product.

ENVIRONMENTAL PROTECTION

This product is labeled under the Waste Electrical and Electronic Equipment (WEEE) Directive. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health.

This product must not be treated as household waste. The product must be handed over to the applicable collection point for the recycling of electrical and electronic equipment. For more detailed information about the treatment and recycling of this product, please contact your local authority, the household waste disposal office, or the store where you purchased the product.

INFORMATION REQUIREMENTS FOR ELECTRIC LOCAL SPACE HEATERS

Model Identifier: EWH 201

Item| Symbol| Value 1| Unit| Item| Jednotka
Heat output| Type of heat input for electric storage local space heaters only (select one)
Nominal heat

output

| Pnom| 2,0| kW| Manual heat charge control, with integrated thermostat| No
Minimum heat output (indicative)| Pmin| 1,0| kW| Manual heat charge control, with room and/ or outdoor temperature feedback| No
Maximum continuous heat output (indicative)| Pmax,C| 2,0| kW| Electric heat charge control, with room and/or outdoor temperature feedback heat charge control, with integrated thermostat| No
Auxiliary electricity consumption| Fan assisted head output| No
At nominal heat

output

| elmax| –| kW| Type of heat output/room temperature control (select one)
At minimum heat

output

| elmin| –| kW| Single stage heat output and no room temperature control| No
In standby mode| elSB| 0,39| W| Two or more manual stages, no room temperature control| No
 | With mechanic thermostat room temperature control| No
With electronic room temperature control| No
With electronic room temperature control plus day timer| No
With electronic room temperature control plus week timer| Yes
Other control options (multiple selections possible)
Room temperature control, with presence detection| No
Room temperature control, with open window detection| Yes
With distance control option| No
With adaptive start control| No
With working time limitation| Yes
With black bulb sensor| No
Contact details:| ELÍZ – ohrievače vody s.r.o., Technická 7 821 04 Bratislava, Slovakia

Tel.: + 421 2 5363 4207
www.eliz.sk
[email protected]

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>