cardo Spirit Bluetooth 5.2 Intercom Instruction Manual

SPIRIT MANUAL

INTRODUCTION

Thank you for choosing the Cardo SPIRIT communication and entertainment system for motorcycle helmets. We wish you a great SPIRIT experience and encourage you to visit www.cardosystems.com/support/spirit/ regarding any questions, suggestions or comments you may have. If you have not yet installed the SPIRIT unit on your helmet, please install it as described in the Installation Guide provided in the package. You can also watch the installation video accessible on that link
www.cardosystems.com/spirit-installation/ For easy reference while on the road, download the Pocket Guide from www.cardosystems.com/wpcontent/uploads/guides/pocket/en/spirit.pdf And don’t forget to register your SPIRIT. Registering your SPIRIT allows you to download software updates, enjoy new features that are offered from time to time, and assures the smooth handling of warranty issues you may have. Also rest assured: Cardo does not share your details with others. This is version 1.0 of the SPIRIT Manual. The latest version of the manuals in your preferred language and various tutorials can be found at www.cardosystems.com/wp- content/uploads/guides/manual/en/spirit.pdf

GETTING STARTED

2.1 GETTING TO KNOW YOUR SPIRIT

2.2 CHARGING YOUR SPIRIT

Make sure that your SPIRIT battery is charged for at least 4 hours before initial use.
To charge the unit:

1. Using the supplied USB cable, connect your computer or wall charger to the USB port on your SPIRIT.

2. Fast charging
   You will have 2 hours of Talktime after 20 mins of charging. (1.5 – 2 hours for full charge).

3. Charge while riding: In case you need to charge it, connect your unit to a power outlet. You can continue charging while riding. The battery of your SPIRIT supports up to 10hours of Talktime.

Charging with the wall charger is faster than via a computer USB port.
Charging your unit switches it off automatically. To use your unit while it is being charged, switch it on. (see
Switching Your Unit On/Off on page 5).
While charging, the LED indicates the charging status as follows:

• Red LED on — charging
• Red LED off — charging complete

2.3 SWITCHING YOUR UNIT ON/OFF
To switch your SPIRIT on:

The speaker plays an ascending tone and a voice message greets you.
The LED confirms your SPIRIT is on:

• Normal battery — LED flashes blue three times.
• Low battery — LED flashes blue three times, then red.
• Charging — LED flashes red, blue, and purple.

To switch your SPIRIT off:

The LED flashes red three times, confirming that your unit is switching off. The speaker plays a descending tone and a voice message.
2.4 USING YOUR SPIRIT
You can operate the various features of your SPIRIT in the following ways:

• Press a button or combination of buttons on the unit
• Use the Cardo Connect App on your mobile device (once it is paired with the unit)

2.5 PAIRING YOUR UNIT TO BLUETOOTH DEVICES
Your SPIRIT has two Bluetooth channels for connection to Bluetooth devices such as mobile phones, GPS devices, and Bluetooth music players with A2DP. To connect your unit to a Bluetooth device, you must first pair them. Once paired, they automatically recognize each other whenever they are within range.

• If you are pairing more than one device, Cardo recommends that you pair the mobile phone to channel 1, and the additional device (such as GPS, music player or additional mobile phone) to channel 2.
• If you are pairing the unit to more than one mobile phone, the phone paired with channel 1 is the default phone for outgoing calls.

To pair Bluetooth channel 1 to a mobile phone:

1. Enable Bluetooth on the mobile phone.
2. On the unit in standby mode, press >

The LED flashes red and blue.
3. On your mobile phone, search for Bluetooth devices.
4. When your SPIRIT appears in the list of available devices, select it.
If prompted for a PIN or Passkey, enter 0000 (four zeros).
The phone confirms that pairing has succeeded and the LED flashes purple for 2 seconds.
To pair Bluetooth channel 2 to another Bluetooth device:
1. Enable Bluetooth on the device (for example, your mobile phone, GPS device, or music player).
2. On the unit in standby mode, press for  >   5 seconds.
The LED flashes red and blue.
3. Do the following:
a. GPS device: Tap. >   The LED flashes red and green.
b. Mobile phone: Tap. > The LED flashes red and green. Tap +
3. On the device you are pairing, search for Bluetooth devices.
4. When your SPIRIT appears in the list of available devices, select it. If prompted for a PIN or Passkey, enter 0000 (four zeros).
The device confirms that pairing has succeeded and the LED flashes purple for 2 seconds.

• If pairing is not completed within 2 minutes, the unit automatically returns to Standby.
• Not all Bluetooth mobile phones broadcast Bluetooth Stereo music (A2DP) even if the phone has an MP3 player function.
• Consult your mobile phone’s user manual for more information.
• Not all Bluetooth GPS devices allow connection to Bluetooth audio devices. Consult your GPS User Manual for more information.

To cancel the pairing process:
Press the Media button > for 2 seconds.
The LED stops flashing red and blue/green.
3. CARDO CONNECT APP
The Cardo Connect App enables you to configure the settings of your SPIRIT. In addition, the App offers you remote-controlled operation from the screen of your smart. phone.
3.1 REGISTERING YOUR UNIT

1. Download the Cardo Connect App.

http://onelink.to/sup9q3

Register your SPIRIT.

1. Select your language.

3.2 UPDATING YOUR UNIT
Before using your unit for the first time, and whenever a new software update is available, make sure to have the latest software update. Updating with the latest software keeps your unit free of bugs and provides you with additional new functionalities.
Your SPIRIT can be updated Over the Air, via the Cardo Connect app.
To update your SPIRIT unit with the Cardo Connect App:
Whenever a new software update is available, a pop-up will open on your App screen. Press Install and follow the on-screen instructions.
If you press Remind me later, the pop-up will re-open the next day.
To update your SPIRIT at any moment

1. Open Cardo Connect app.
2. Press Settings.
3. Select your unit.
4. Select the software version.
5. Press Update Now. When the update is finished, press Finish going back to the main screen.

To update your SPIRIT unit with your computer:

1. Download and install the Cardo Update tool https://www.cardosystems.com/update
2. Open Cardo Update.
3. Register (first time only).
4. Connect the unit to the computer using a USB cable and update the firmware.
   Cardo Update on Windows / Mac – minimum requirements – Windows® 7 / macOS X 10.8

4. ON THE ROAD
SPIRIT makes it easy for you to receive phone calls and listen to music in a convenient and safe manner.
4.1 BASIC AUDIO FUNCTIONS
The basic audio functions are the same whether you are listening to music, speaking on the intercom, or having a phone conversation.
To turn the volume up:
Tap Volume up **+**to increase the volume.

An increasingly louder tone is played on the speaker until you reach the maximum volume, as indicated by the maximum volume tone.
To turn the volume down:
Tap Volume down **-**to reduce the volume.

An increasingly quieter tone is played on the speaker until you reach the minimum volume, as indicated by the minimum volume tone.
To mute the microphone completely and lower the speaker volume to the minimal level:
Tap Volume down- for 2 seconds to mute the microphone.

To unmute the microphone and raise the speaker volume to the previous level:
Tap any button.
4.2 MAKING AND RECEIVING PHONE CALLS
You can use your mobile phone to make and receive phone calls while paired to your SPIRIT.
You can make a hands-free call using your mobile phone’s voice dial option or using the Cardo speed dial or redial last call options.
To make a phone call:

• To dial using your mobile phone’s voice dial option, tap or say “Hey Siri” (if you are using an iOS device) or “OK Google” (if you are using an Android device), then make your call as per the instructions for your mobile device.
• To dial your preset speed dial number, tap twice.

To answer a call:
Tap the mobile button

To ignore a call:
Tap volume down **-**

To end a call:
Tap the mobile button.
4.3 STREAMING MUSIC
You can stream music from your paired device to your SPIRIT. To start a music streaming from your paired device:
Tap the Media Button** >**

To stop music streaming:
Tap mobile**>** and volume down**- ** To skip to the next track (while streaming):
Tap the media button.**>**

To skip back to the previous track (while streaming):
4.4 SWITCHING MUSIC SOURCES
If two music (A2DP) audio sources are paired, SPIRIT uses the audio source from which you last played music.
To switch to the other audio source:

1. Stop music (A2DP) playback from the current device.
2. Play music (A2DP) from the other device. SPIRIT automatically remembers your last played device.

5. RIDING WITH OTHERS
Your SPIRIT features the traditional Bluetooth protocol intercom communication mode.
5.1 BLUETOOTH INTERCOM
To connect your unit to another unit with a Bluetooth intercom, such as a Cardo Bluetooth unit or other Bluetooth-enabled devices, you must first pair their channels. Once paired, the unit automatically recognizes the other one whenever they are in range (line of sight up to 400m / 0.25mi subject to terrain).

• Pairing a channel replaces any existing paired unit on that channel with the new unit.
• If you purchased the SPIRIT DUO, the retail package contains two pre-paired units.
• The Intercom range with other models is limited to the distance of the unit with the shorter range.

5.1.1 SETTING UP BLUETOOTH INTERCOM CONNECTION
To set up a Bluetooth connection:

1. Confirm your unit is in Standby mode (LED flashes slowly).
2. To initiate 2-way pairing:

On your unit, press   for 5 seconds to enter pairing mode.
The LED flashes red.

• The following announcement is heard: Rider A pairing.
• Bluetooth intercom pairing needs to be initiated on the other device.
• To cancel the pairing process, press  for 2 seconds. The LED stops flashing.
• If pairing is not completed within 2 minutes, the unit automatically returns to Standby.

To pair a non-Cardo Bluetooth intercom unit:

• The non-Cardo unit should be on phone pairing mode.
• All the steps are the same as with a Cardo Bluetooth intercom group.

5.1.2 USING THE BLUETOOTH INTERCOM
5.1.2.1 STARTING/ENDING BLUETOOTH INTERCOM CALLS
To start or end communication with a rider or passenger:

5.1.2.2 RECEIVING BLUETOOTH INTERCOM CALLS
If another paired unit calls you via Bluetooth intercom, the call begins instantly.
5.2 SHARING MUSIC

• You can share music with a passenger or other rider.
• Music can be shared with only one passenger/rider.
• Bluetooth intercom calls are disabled when sharing music.
• If you paired your unit to two mobile phones, music will be shared from the mobile phone through which you last played music.
• When you stop sharing music, the music continues to play on your unit only.

To start sharing:

Press **>**and **+** for 2 seconds to start sharing on channel A (by default).
To stop sharing:
Press the Volume Up button **+**for 2 seconds.

TROUBLESHOOTING

6.1 SOFT RESET
If your SPIRIT stops responding, reset it in one of these ways:

• Turning it off and then on again (see Switching Your Unit On/Off).
• Using the supplied USB cable, connect your unit to the computer or wall charger for 30 seconds.

6.2 RESET TO FACTORY SETTINGS
This option deletes all paired devices and all configuration settings.
To perform a factory reset through the unit:
1. Check that your SPIRIT is in Standby mode (see SPIRIT Modes and Events – LED Indications).

2. Simultaneously press + **+**+ **-** for 5 seconds.

The LED flashes purple 5 times slowly, confirming that the pairing has been reset.
6.3 FAQ
Additional answers to common problems can be found at www.cardosystems.com/support/spirit/

PERSONALIZING YOUR DEVICE

Get the most out of your SPIRIT by changing the settings and customizing your unit according to your own personal preferences, using either of the following methods:

• Cardo Connect App on iOS or Android devices.
• Unit buttons.
  Cardo recommends you customize your settings before going out on the road. You can adjust any of these settings as required after experiencing them under road conditions.

Object| Default
Value| Description| Cardo Connect App
(iOS/Android)
---|---|---|---
Cardo Conned App
(105/Android)
✓
AGC sensitivity  (Off/Low/Medium/High)| Medium| AGC automatically adjusts speaker volume according to ambient noise and riding speed. For example, when set to Low, higher ambient noise will cause the volume to increase to kick in at a higher level.
Audio priority (A2DP/Bluetooth intercom)| Bluetooth intercom| Priority of audio source playing through speakers. Either music is not interrupted by an intercom call, or vice-versa.| ✓
Background Audio Level| N/A| Sets the background audio volume when parallel audio streaming is on (see Parallel audio streaming in Bluetooth mode (Enable/Disable) below).| ✓
Bluetooth friendly name| SPIRIT| Sets the name that appears on your phone while pairing and in the Cardo app.| ✓
Language| According to Your Region| Voice announcements and voice-assisted menus language (see “Spoken Status Announcements” below).| ✓
Mobile priority| Mobile 1| If you paired your unit to two mobile phones, you must
set one of them as the default phone for outgoing calls.| ✓
Parallel audio streaming in Bluetooth mode (Enable/Disable)| Disable| You can hear two audio sources simultaneously. For example, hear GPS while listening to music.
Note: Parallel audio streaming may not work properly with some iOS devices (i.e., music player or GPS navigator) due to connected device limitations.| ✓
Set speed dial numbers| Empty| Pre-set phone numbers for automatic dialing.| ✓
Spoken Status Announcements (Enable/Disable)| Enable| Voice announcements inform you to whom or to what device you are connected.| ✓

AGC and voice control performance vary based on environmental conditions, including riding speed, helmet type, and ambient noise. For improved voice control performance, minimize the wind impact on the microphone by closing the visor and using the large microphone sponge.
7.1 USING PARALLEL AUDIO STREAMING
With parallel audio streaming, you can hear GPS instructions during a mobile or Bluetooth intercom call, or while listening to other audio sources, such as music.
Parallel audio streaming may not work properly with some iOS devices (i.e., music player or GPS navigator) due to connected device limitations.
Your SPIRIT sets the various audio sources to either foreground (volume remains the same) or background (volume reduced) as described in the following table:

1If you add an intercom call to a mobile phone call creating a conference call, the volume for both audio sources is the same.
2If you make two intercom calls simultaneously creating an intercom conference call, the volume for both audio sources is the same.
3If you make two intercom calls simultaneously creating an intercom conference call, you cannot hear the mobile phone or GPS.
4If you play music only, the music volume is not reduced.
In some cases, parallel audio streaming may not work properly due to connected device limitations (music player or GPS navigator).
You can configure parallel audio streaming via the Cardo app.

7.2 AUDIO SOURCE PRIORITIES
If Parallel Audio Streaming is disabled, SPIRIT manages the audio sources you hear through the speakers according to the following audio source priorities.

Higher Priority
↑
Lower Priority| Mobile phone, GPS device instructions 1
Intercom or Music2
Music or Intercom3

1Phone calls and GPS temporarily mute the intercom, but group members remain part of the intercom group.
2When audio priority is set to Intercom, you cannot hear navigation apps or SMS messages from your phone during an ongoing intercom call.
3When audio priority is set to A2DP (music), the intercom is disabled while listening to music (via A2DP). A rider calling you by intercom hears a sound indicating you are not available.
If you paired your unit to two mobile phones, music will be shared from the mobile phone through which you last played music

GLOSSARY

music over Bluetooth.
AGC sensitivity| AGC (Automatic Gain Control) automatically adjusts speaker volume and microphone sensitivity according to ambient noise and riding speed.
Device| Mobile phone, GPS, or music player.
Language| Voice announcements.
Unit| Cardo or non-Cardo Bluetooth Communication system.
Voice control| Voice activation (by saying a word or phrase)
Voice control sensitivity| Adjust your microphone sensitivity for voice activation while you are riding.

SUPPORT

• For additional information: : www.cardosystems.com/support/spirit/
• To avoid potential problems and to receive our support and warranty coverage, we strongly recommend buying our products only from authorized Cardo dealers.
• Your favorite brick-and-mortar store is always your best bet. Unauthorized online resellers and online auction sites such as eBay are not among Cardo’s authorized dealers, and purchasing our products from such sites will be at your own risk. Cardo strives to provide quality products and exceptional customer service. We select dealers who share that vision. Buying grey market items from unauthorized online dealers is counterproductive and also adversely affects unsuspecting online consumers who may be purchasing used, counterfeit or defective products or devices whose warranties are void. Protect your investment by purchasing genuine Cardo and scala rider® products only from authorized dealers.

© 2022 Cardo Systems
All rights reserved. Cardo, the Cardo logo, and other Cardo marks are owned by Cardo and may be registered. All other trademarks are the property of their respective owners. Cardo Systems assumes no responsibility for any errors that may appear in this document. Information contained herein is subject to change without notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>