Blast Radio Blast Box Musicians Stream User Manual
- June 6, 2024
- Blast Radio
Table of Contents
Blast Box Manual
Charging Device Blast Box can be charged through any micro USB cable connected
to a powered source.
Audio Input
Blast Box capture audio from any audio source through the RCA input in the
back of the device.
Headphone Monitoring and Volume Knob
There is a headphone jack on the front of the device that can be used to
monitor playback and ensure that audio is being captured through the device
properly. The volume knob can be used to raise and lower the headphone
monitoring volume but does not affect the capture and broadcast volume.
Buttons
Power Button (magenta) – Turns on and off the device, activates pairing mode,
starts and stops a recording or broadcast. Mode Button (cream) – Toggles
between Live Mode and Offline Mode.
Turning On and Off Device
When the device is turned on, press and hold the Power button to turn on the
device.
When the device is turned off, press and hold the Power button to turn off the
device.
Pairing Device Over Bluetooth
- Press and hold the Power button.
- Continue holding the Power button past the device powering on for 3 seconds until pairing mode is displayed on the screen.
- On your iOS or Android device, select “Blast Box” from the Bluetooth menu.
Connecting Device to Blast Radio App
- Pair the device with your iOS or Android device via Bluetooth.
- Open Blast Radio app. If you are not already logged in to your account be sure to log in. If you do not have an account, you must create an account and verify it.
- Your device should appear when you select “Start Broadcast” from the home screen.
Connecting Device to WiFi
Note: A WiFi connection is necessary to record all audio to your iOS or
Android device. This is in order to ensure the highest quality audio and
minimize dropouts when streaming live.
- With your device paired and appearing in the Start Broadcast section of your Blast Radio App, press the “i” button.
- Choose from the available, detected WiFi networks.
- Enter the WiFi network’s password.
- Once the connection is established, the WiFi and Password will be saved securely with your Blast Radio account in order to work with any Blast Box.
Broadcasting Live
- With your device on, paired, and connected to WiFi, press the Power button to start broadcasting when in Live mode The word LIVE appears in the top left corner by default, denoting Live Mode). If not in Live Mode, press the Mode button to toggle Live Mode on.
- A countdown timer will appear to count down from 3 and then start broadcasting live.
- Press the Power button to send a broadcast.
Notes:
- Broadcasts can also be started and stopped through the Blast Radio App broadcast screen.
- When in Live Mode, the current listener count is displayed in the top right corner.
- The display will flash red in order to signify a “vibe”. Vibes are activated when a new listener joins the broadcast or when a listener sends a reaction.
Offline Recording
- With your device on, paired, and connected to WiFi, press the Power button to start broadcasting when in Offline Mode The word LIVE appears in the top left corner by default, denoting Live Mode). If in Live Mode, press the Mode button to toggle Live Mode off to enter Offline Mode.
- A countdown timer will appear to count down from 3 and then start broadcasting live.
- Press the Power button to end a broadcast.
Factory Reset
With the device off, press and hold the Power and Mode buttons together for
20 seconds.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment
The devices have been evaluated to meet general RF exposure requirement the
device can be used in portable exposure condition with restriction
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>