Dongguan City Xuanyixuan Technology GEPC363AB Wireless Mouse User Manual

Dongguan City Xuanyixuan Technology GEPC363AB Wireless Mouse

PACKING LIST

• Mouse
• USB Receiver
• User Manual
• Charging Cable

DIAGRAM

1. Left Button
2. Right Button
3. Scroll Wheel
4. DPI Button
5. Power Indicator Light
6. Forward Button
7. Backward Button
8.  Charging Port
9. Light Switch
10. Button 10.0n/Off
11. USB Receiver

FEATURES

1. RGB Backlight. Both left and right sides have RGB light strips that support lS RGB light effects. Short press the bottom light switch button to switch light effects. Long press to turn on or turn off RGB backlight.
2. 3 Levels DPI. 800/1200/1600. Short press DPI button to switch in cycle. The default DPI is 7200.
3. Power-saving mode: the mouse will automatically enter into sleep mode without operation of l5min. Press any button to wake it up.
4. Rechargeable Design. Built-in 650mAh lithium battery. The mouse can be recharged with included charging cable. When the battery is running low, its indicator light will light on to remind you of charging. The light will keep on during charging and go out once it’s fully charged.

INSTRUCTIONS

1. For first use, please fully charge the mouse.
2. Turn on the mouse when fully charged.
3. Open the cover to take out USB receiver and plug it into computer. The mouse will work after its driver is installed on computer automatically.

SOLUTIONS TO 2.4G WIRELESS CONNECTION ISSUES
Turn off the mouse and turn it on again, press left, right button and scroll wheel simultaneously for 3-5s and then release. Plug the USB receiver into computer and the mouse will work.

NOTE
If the product is sti 11 unworkable after above solutions, you cou Id repeat those steps for a few ti mes. If your problem can’t get solved yet, please contact our Customer Service for help (Email: csforcustomer@gmail.com)..)

FCC STATEMENT

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: OJ This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC RADIATION EXPOSURE STATEMENT:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

CORRECT DISPOSAL OF THIS PRODUCT
( Waste Electrical& Electronic Equipment ) This Marking shown on the product or its literature,indica-te that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household user should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contact. This product should not be mixed with other commercial wastes for disposal.

FCC Information and Copyright
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC RF warning statement: the device has been evaluated to meet general RF exposure requirements, The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>