Shenzhen Hengyehui Technology W11 Car Wireless Charger Phone Holder User Guide
- June 6, 2024
- Shenzhen Hengyehui Technology
Table of Contents
Shenzhen Hengyehui Technology W11 Car Wireless Charger Phone Holder
Magnetic suction automatic positioning wireless charging mobile phone
holder.
This product is only compatible with iPhone 12 series.
Please read this operation
Instruction carefully and keep it properly before using this product.
Product Introduction
Thank you for purchasing and using this products! In order to ensure that you can provide a better operating experience for your mobile phone or electronic products.
Applicable model
| Compliance with QI standard cell phone.
---|---
Input power| 5V / 2A1 9V/ 1.7A I __ l 2V/ 1.SA| Output Power|
5W/7.SW/10W/1SW
Working frequency| 700″‘205KHZ| Efficiency|
80%-83%
PS: these above information is based on real sample testing/it will be a little bit different for different products in different conditions.
Operation
-
Please wipe the car dashboard carefully with the damp cloth.
-
Paste the patch on the dashboard.
-
Press the air switch so that the suction cup is firmly attached to the instrument panel.
-
Plug in the charging cable, shake the phone to align the magnets then complete the installation.
-
Loosen the nut and remove the wireless charger.
-
Other bracket bases can be replaced.
-
lnstall the bracket to the vent1 tighten the bracket by rotating the nut/ and then connect the car charger and mini USB cable that meet QC3.0 standard for power supply.
⚠ Note
- Please align the phone magnet with the wireless charging magnet to avoid the magnetic attraction does not work.
- Please make sure you are using Magsafe Cases. It can’t compatible with non-MagSafe cases. non-MagSafe cases make the magnetic force is weak and can’t charge.
- Please make sure you mount the 3M Gel Plate first. 3M Gel Plate included in the package.
- No metal plate on the back of the phone, because it will stop the phone charging.
- Don’t use the wireless charger in high temperature, humidity or corrosive environmentavoid damaging the circuit and avoid leakage.
- Take care of the children to ensure that they will not play the wireless charger as a toy/ to avoid unnecessary accidents.
- To ensure the fast and safe charging /we select the QC2.0/QC3.0/standard car charger and the best four-core universal data cable /others nonstanda rd car charger or cables will make the charging slow.
- If the car temperature inside is too high 1 the charging will become slow; with the cold wind from the air outletcharing on the air outlet will be much better /with the hot wind from the air outlet /pls charging the mount on the dashboard.
FCC Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Radiation Exposure Statement
This device complies with RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. This device must operate
with a minimum distance of 20 cm between the radiator and user body.