Shen Shing Electric SB8STPK-A-RM Waterproof Multicolor Strip Light User Manual
- June 6, 2024
- Shen Shing Electric
Table of Contents
User Manual
Waterproof Multicolor Strip
WARNING
PLEASE READ AND UNDERSTAND THIS ENTIRE MANUAL BEFORE INSTALLATION.
- Please carefully remove the plastic film.
- Please gently unravel the strip light from the roller circle.
- DO NOT stretch or twist the LED strip light as this will damage it.
- DO NOT power the LED strip light while it is on the roller as it will overheat
- DO NOT use the light in water.
- This is a strip light, not a cable, so treat it like one. DO NOT puncture, cut or shorten the light.
- Ground Fault Circuit Interrupter (GFCI) protection should be provided on circuits or outlets to use strip lights outdoors. Receptacles with built-in GFCI protection are available for this measure of safety.
- ONLY use on 120V AC.
- DO NOT cover this product as the cover may cause the light to overheat and melt or ignite.
- DO NOT operate this product while the light is tightly coiled.
- DO NOT use if there is any damage to the product or the cord insulation.
- Secure this strip light using ONLY the hangers or clips provided. DO NOT secure this product or its cord with staples, nails, or similar means that may damage the insulation or permanently attach to the building structure.
- The max extension length for this strip light is 100ft.
- This product has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock. This plug will fit in a polarized outlet ONLY one way. f the plug DOES NOT fit fully in the outlet, PLEASE reverse the plug. If it still DOES NOT fit, PLEASE contact a qualified electrician.
- DO NOT mount or secure the strip light in a manner that can cut the outer jacket or damage the cord insulation.
- DO NOT install the strip light in cabinets, tanks, or enclosures of any kind.
- DO NOT install the strip light near flammable liquids.
- Wash your hands after using. Handling this product may expose you to chemicals.
- This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov
- Please align the pins correctly when connecting the strip lights and tighten the waterproof wire nuts before use.
- Stretch the signal receiver wire to increase the signal intensity.
- This LED strip light is bendable. The minimum bend radius is 1.57inch.
PACKAGE CONTENT
INSTALLATION
CAUTION: These products may represent a possible shock or fire hazard if improperly installed or attached in any way. Products should be installed in accordance with these instructions, current electrical codes, and/or the current National Electric Code (NEC). Only use this strip light with the plug- in power cord that is supplied with the strip light. Any other power cord or feed may damage the strip light. LIGHT STRIP MOUNTING
| Carefully remove the Strip Light (A) from the package and uncoil it. Be
careful not to cut it.
---|---
| Ensure that the Power Cord (B) and the Waterproof Plug (E) are securely
fastened tooth ends of the Strip Light (A) in order to prevent water from
entering.
| Attach Plastic Clips (C) with MountingScrews (D) to the wall’s surface.
| Snap the Strip Light (A) into the Plastic Clips (C). Installation is now
finished.
| Plug the Power Cord (B) into the outlet and turn the Strip Light (A) on.
Note: If installed outdoors, please use a Ground Fault Circuit Interrupting
(GFCI) outlet
for safe operation.
EXTENSION MOUNTING
NOTE: The max extension length for this strip light is 100ft. Do not exceed 100ft when linking extension segments together.
| 1. Ensure that all Strip Lights are unplugged before adding any additional
Strip Lights to the series.
---|---
| 2. Remove the Waterproof Plug (E) from the end of the Strip Light (A].
| 3. Connect the end of the Strip Light(A1)to the head of the other Strip
Light(A2). Ensure that the connection is secured tightly to prevent water from
entering.
| 4. Ensure that the Waterproof Plug (E) is securely fastened to the end of
the last Strip Light in order to prevent water from entering.
REPLACE THE FUSE
NOTE: Disconnect power before replacing the fuses. Grasp plug and remove
from the receptacle or other outlet devices. Do not unplug by pulling on the
cord.
| Open the fuse cover by sliding it over the attached plug towards the blades.
---|---
| One spare fuse is in the plug. Turn the fuse holder over to remove the spare
fuse.
| Turn the fuse holder back over. Gently pry the end of the fuse nearest the
plug with a small blade screwdriver (not included) to remove the old fuse.
| Replace the old fuse with the spare fuse.
| Slide the fuse cover to the original position to close.
HOW TO USE
Use ON and OFF buttons for power control and refer to the chart below for
button functions and mode options. There are 24 keys on the control panel for
this 433M RF
remote controller.
| RF| |
---|---|---|---
ON| Static RED| Static ORANGE
OFF| Static GREEN| Static YELLOW
SPEED+| Static BLUE| Static CYAN
SPEED-| Static WHITE| Static PURPLE
Brightness| Brightness 80%| Brightness50%| Brightness 30%
100%| 3 colors fade| 1 color shines| START/SET
3 colors jump| 7 colors fade| 3 colors shine| PAUSE
| | |
NOTE:
A. When it is in”Static” mode, Brightness 100%/Brightness 80%/Brightness
50%/Brightness 30% mean different brightness of light modes.
B.When it is in “Dynamic” mode, “SPEED+” means increasing the speed, and
“SPEED-.” means decreasing the speed.
C. It can memorize the last setting before power off.
D 3 colors jump: The strip light shines in 3 RGB colors ( red. green & blue).
7 colors jump: The strip light shines in 7 colors.
E.3 colors face:3 RGB colors (red, green & blue) will be slowly changed, from
one color shade to another, without flashing.7colors fade: 7 colors will be
slowly charged, from one color shade to another, without flashing.
F: 1 color shines: The strip light flashes in a specified color.
G: If there are several RF transmitters and receivers in a small range, they
may affect each other because 433M RF remote control’s distance is long So a
specific identification code has been added to this new version remote control
to prevent the interference.
PAIR & UNPAIR OPERATIONS
Each strip light has been paired with a remote control before leaving the
factory, so you can use the strip light directly without any extra
operation.But you may need to pair the remote control again when it cannot
control your strip light correctly.
NOTE: Unpair the remote control before pairing it again.
HOW TO UNPAIR THE RF REMOTE CONTROL
NOTE: The valid time of unpairing is 1 minute. Please complete unpairing
the RF remote control in 1 minute.
-
Turn off the strip light if it’s on and disconnect the strip light from the power
supply. Then wait at least 10 seconds before turning on the strip light. -
Turn the strip light on. Put the remote control close to the controller in the power cord. Hold the “PAUSE” button on the remote control for 3-5 seconds. If the strip light flashes in blue and purple, then the unpairing is successful. The unpairing is now complete. Other remote controls can also control this strip light now.
HOW TO PAIR THE RF REMOTE CONTROL
NOTE: The valid time of pairing is 1 minute. Please complete pairing the
RF remote control in 1 minute.
- Turn off the strip light if it’s on and disconnect the strip light from the power supply. Then wait at least 10 seconds before turning on the strip light.
- Turn the strip light on. Put the remote control close to the controller in the power cord. To pair the remote control, press and hold the “START/SET” button on the remote control for 3-5 seconds. If the strip light flashes in red and green, then the pairing is successful. The controller now only receives control instruction from this remote control, regardless of interference from other remote controls and products.
SPECIFICATIONS
Light Strip
| Input voltage| AC 120V
---|---|---
Material| PVC
Waterproof rating| IP67
Working location| Indoor & outdoor
Length| 50ft
Lifespan| 50,000hrs
Working temp| -31°F-113°F
LED Chip
| Quantity| 80pcs
Size| 5050
RF Remote Control
| Working temp| -4°F-140°F
Output signal| RGB
Control mode| 433M RF control remote
Attended mode| Common anode
Weight| 150g
| Dimension| 3.94 inch(L) 1.85 inch (W) 1.50 inch (H)
---|---|---
MAINTENANCE
- DO NOT use chemical solvents or harsh abrasives to clean the fixture. Use a soft dry cloth to clean if needed.
- The working temperature for the remote control is -4°F-140°F.
TROUBLESHOOTING
-
The light does not come on at all:
Make sure the wall switch and circuit breaker are both on. -
Fuse blows when the light turns on:
Shorten the total extended length to 100ft or less and replace the fuse in the plug.
WARRANTY
warrants that this product is free from defects in materials and workmanship
for a period of 12 months from the day of purchase. If the product has been
misused, damaged by accident, or in any other way of improper use, this
warranty becomes void.
FCC Statement
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Radiation Exposure Statement
This device complies with RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>