Vanergy HF001 Bluetooth Earphone Instructions

Vanergy HF001 Bluetooth Earphone

Bluetooth Earphone

Features

• Made from premium knitted material.
• Built-in microphone for answering or calling.
• Hand-washable are removing the Bluetooth modules.
• Compatible with any Bluetooth-enabled device.
• Universal micro-USB cable.

Specifications

• Bluetooth Version: 5.0 + EDR
• Frequency:2.402 GHz-2.480 GHz
• Standby time: up to 120 hours
• Music playing time: up to 12 hours
• Transmission distance: 15 m(45ft)
• Battery: Li-ion 3.7V/180mAh
• Charging time: 2 hours
• Talking tme: up to 12 hours

At a Glance

Turning On/Off Bluetooth Earphone

Pairing Bluetooth Earphone

1. Turn on Bluetooth on devices
2. Turn on Music Headband
3. Connect to Music Headband on devices

LED STATUS COLOR////////////////MEANING

• Rapidly flashing blue and red
• Slowly flashing blue
• Pending to be Paired
• Connected to a device

Note: When turned on, the Music Headband will automatically connect to the last connected device if available.if no previously paired device is detected,it will keep pairing mode

Control

Charging the Bluetooth Earphone

Washing instruction removal of electronics

Please note that you MUST remove the control panel & speaker before washing your Bluetooth Headband

How to Remove the control panel & speakers

• Step 1 The control panel is held in a pocket between a double layer inside the Headband. You can gently ease the control
• Step 2 You will see a  small opening at the rear of the Bluetooth Headband Continue to ease the control panel towards this opening.
• Step 3 Repeat step 1 for the additional speaker located at the opposite side of  the Bluetooth Headband

Precautions

• Do not expose the Headband to liquid or moisture.
• Do not attempt to tamper with Headband by dropping, disassembling, or opening.
• Remove the Bluetooth module before washing the Headband.
• Keep the Headband away from fire.
• Do not store the Headband near acidic or alkaline material.

Once the electronics are completely removed:  Machine wash cold, air dry (Do NOT tumble dry).

Bluetooth Earphone

TECHNICAL SPECIFICATION

Material: 95%Polyester + 5% spandex Rated Power: RMS 10mW x 2 Speaker Unit: 32Ω/20mm Frequency Response: 20HZ-20khz Plug and play  Audio lnput:Universal 3.5mm Audio Jack

How to remove the Speakers

• The headset is held between a double layer inside the  Headband. You can gently take the speakers out of its pocket.
• You will see a small opening at the rear of the Headband. Continue to ease the speakers towards this opening.
• Repeat step 1 for the additional speaker located at the opposite side of the Headband.

Precautions

• Do not expose the Headband to liquid or moisture.
• Do not attempt to tamper with Headband by dropping,
• disassembling, or opening.
• Remove the headset module before washing the Headband.
• Keep the Headband away from fire.
• Do not store the Headband near acidic or alkaline material.

Warranty

12-Month Warranty and friendly customer service. Once the electronics are completely removed: Machine wash cold, air dry (Do NOT tumble dry).

FCC

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and

• this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
  NOTE:
  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
  However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help. .
  • The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction FCC ID: 2AZIWHF001

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>