WORKZONE RCUS 1464865 Rechargeable Led Work Light User Manual

WORK ZONE RCUS 1464865 Rechargeable Led Work Light

Package contents

Components

1. Handle
2. USB charging cable
3. Battery level indicator
4. Battery level indicator button
5. Micro USB port
6. USB port
7. Protective cover
8. On/off switch
9. USB power adapter

The package contents include a built-in Li-ion battery (6,600 mAh).

General information Reading and storing these instructions

These instructions are for this rechargeable work light (referred to as “light” below). They contain important information on setup and handling. Before using the light, read the instructions for use carefully. This particularly applies to the safety instructions. Failure to do so may result in serious injury or damage to the light. Store these instructions for any further use. Make sure to include these instructions when passing the light on to third parties.

Proper use
The light is designed exclusively to illuminate indoor and outdoor working areas. It is only intended for personal use and is not suitable for commercial use. Only use the light as described in the instructions. Any other use is considered improper and can result in material damage or even in harm to persons. The light is not a toy. The manufacturer or retailer assumes no liability for damage resulting from improper or incorrect use.

Explanation of symbols
The following symbols are used in these instructions, on the product or on the packaging.

Safety

Explanation of instructions

The following symbols and signal words are used in these instructions.

WARNING!

This signal symbol/word refers to a hazard with a medium level of risk that, if not avoided, may result in death or serious injury.

CAUTION!

This signal symbol/word refers to a hazard with a low level of risk that, if not avoided, may result in minor or moderate injury.

NOTICE!

This signal word warns of possible material damage.

General safety information

Risk of electric shock!
Faulty installation of electronics or an excessively high supply voltage may result in electric shock.

• The light source of this work light is not replaceable. When the light source has reached its end of life, replace the entire work light.

• Only plug in the USB power adapter if the supply voltage of the outlet corresponds with the information on the rating label.

• Only plug the USB power adapter into an easily accessible outlet. You can quickly disconnect the adapter from the power grid in the event of an incident.

• Do not operate the light if it is visibly damaged or if the USB charging cable or adapter is defective.

• Do not open the housing. Contact a specialist workshop, for repairs. If you perform repairs on your own, improperly plug in the light or incorrectly operate it, any liability and warranty claims will be deemed invalid.

• In the case of repairs, only parts that correspond to the original device data may be used. This light contains electrical and mechanical parts that are essential to ensuring protection against sources of danger.

• Do not submerge the light, the USB charging cable or the USB power adapter in water or other liquids.

• Do not position the light above tubs, sinks or other objects filled with water.

• Never try to pick up an electronic device connected to the grid if it has fallen into water. If this happens, immediately unplug the power plug from the outlet. Never handle the USB power adapter with wet hands.

• Never unplug the USB power adapter from the outlet by the USB charging cable. Always grasp the USB power adapter.

• Keep the light, the USB charging cable and the USB power adapter away from open flames and hot surfaces.

• Do not bend the USB charging cable or lay it over sharp edges.

• Never operate the light in damp rooms or in the rain.

• If the battery is fully charged, you would like to clean the light or a malfunction occurs, always switch off the light and unplug the USB power adapter from the outlet.

• Keep the light, the USB charging cable, and the USB power adapter away from children.

• The battery cannot be replaced. Never try to replace the battery.− Only charge the battery indoors.
  WARNING! Risks to children and people with reduced physical, sensory or mental capabilities (for example, partially disabled people, older people with limited physical and mental capabilities) or a lack of experience and knowledge.

• This light can be used by children aged eight and older as well as by people with reduced physical, sensory or mental capabilities or a lack of experience and knowledge if they are supervised or have been instructed in the safe use of the light and understand the dangers that result from said use. Children may not play with the light. Cleaning and user maintenance may not be done by children without supervision.

• Keep children younger than eight years of age away from the light and the connecting line.

• Do not let children play with the packaging film. Children may get caught in it and suffocate if they play with it.

WARNING!

Explosion and fire hazard!
Improperly handling the light and the battery may cause an explosion or a fire.

• Keep the light away from water, other liquids, open flames, and hot surfaces.
• Do not cover the light or the USB power adapter with items or clothing.
• Maintain a distance of at least 2 inches from highly flammable materials.
• Do not expose the light to excessive heat, such as direct sunlight, fire or the like.
• Only charge the light using the supplied accessories.

Risk of chemical burn!
Leaking battery fluid may cause burns if it comes into contact with skin or other parts of the body.

• If battery fluid is leaking, avoid contact with skin, eyes and mucous membranes. If you come into contact with battery fluid, immediately rinse the affected areas with a generous amount of clean water and seek medical attention right away.
• If a battery is leaking, make sure to wear protective gloves and remove the leaking battery fluid using a dry, absorbent cloth.

Risk of injury!
The LED light is very bright and may damage your eyes if you look directly into it.

• Never look directly into the lit LED of the light.
• When using the light, make sure that you do not shine it in anyone‘s eyes or in the eyes of other living things.

Risk of damage!
Improperly handling the light may cause it to become damaged.

• The light source of this light cannot be replaced. If the light source has reached the end of its life cycle, replace the entire light.
• Install the light on an easily accessible, level, dry, heat-resistant, and sufficiently stable work surface. Do not place the light on the edge of the surface.
• Never place the light on or near hot surfaces (hotplates, etc.).− Do not bring the USB charging cable into contact with hot parts.− Do not expose the light to bad weather.
• Do not use the light for longer than 2 hours. To avoid harmful deep discharging, recharge the battery after this period.
• If you do not want to use the light for a long period of time, charge the battery before storage.
• The light cannot be dimmed and may not be operated with an external dimmer.

First use Checking the light and the package contents

Risk of damage!
If you open the packaging carelessly using a sharp knife or other sharp objects, the light may quickly become damaged.

1. Remove the light from the packaging
2. Check the package for completeness (see Fig. A).
3. Check whether the light or the individual parts are damaged. If this is the case, do not use the light. Contact the manufacturer via the service address indicated on the warranty card.

Charging the light
Before using the light for the first time, you must first fully charge the light‘s battery. A full charge usually takes approx. 8 hours.

Risk of damage!
Improperly handling the light may cause it to become damaged.

• Always switch off the light during the charging process.
  • Make sure that the light is switched off.
  • Unwind the USB charging 2 completely.
  • Plug the supplied micro-USB/USB cable into the micro-USB 5 on the light (see Fig. B) and connect the cable to the USB power adapter U , or a computer, laptop, etc. that has a USB port.
  • While charging, the battery level indicator 3 flashes green. (see Fig. B).
  • As soon as the battery is fully charged, all four lights on the battery level indicator will shine green. Disconnect the light from the power supply.

Operation

The light cannot be used during the charging process. The light provides three levels of brightness (100%, 50%, and 25%).

1. To find out the battery‘s charging level, press the Battery level indicator button 4 to view the battery level indicator (see Fig. B). If the battery is fully charged, all four lights on the battery level indicator 3 shine green. The lower the charging level, the lower the number of lit lights. Each light represents 25% of the battery charge. The operating time on a fully charged battery is approx. 2 hours.
2. Using the handle 1 , carry the light to the desired location of use.
3. To set up the light, unfold the handle in such a way that the light hits the area of use at the desired angle.
4. To switch on the light, press the on/off switch 8 (see Fig. B). The LED shines at 100% brightness level.
5. To reduce the brightness, press the on/off switch very lightly. The LED shines at 50% brightness level.
6. To further reduce the brightness, press the on/off switch very lightly once again. The LED shines at 25% brightness level.
7. Press the on/off switch a third time to switch off the light.

Using the battery as a power bank

Connect the device you would like to charge to the light via a USB charging cable (not included) by plugging the USB connector into the USB port 6 (see Fig. B).

Cleaning

Risk of damage!
Improperly handling the light may cause it to become damaged.

• Do not use any abrasive cleaning agents, brushes with metal or nylon bristles or any sharp or metallic cleaning accessories such as knives, hard scrapers and the like. They may damage the surfaces of the light.
• Do not submerge the light, the USB cable or the USB power adapter in water for cleaning and do not under any circumstances put the parts in a dishwasher.
• Do not clean the light, the USB cable or the USB power adapter under running water and refrain from spraying the parts with a garden hose or high-pressure cleaner.
• Remove dust and dirt from the light using a soft, slightly damp cloth.
• If necessary, use a mild detergent for stubborn dirt.

Storage

• Fully charge the battery before storage (see the chapter “Charging the light”).
• Always store the light in a dry place (an indoor environment or garage) that is protected from direct sunlight and out of the reach of children.

Technical data

Light

• Model:                                            869
• Item number:                                 803560
• Dimensions (H × B × T):              approx. 7 x 5 x 1.7 inches (178 x 129 x 44 mm)
• Material:                                        Housing: Aluminium and plastic. Handle: Aluminium and plastic
• Input voltage:                               5 V __
• Protection class:                           III
• Lamp:                                          Epistar COB-LED-Chip, permanently installed
• LED power:                                20 W
• Luminous output:                       2,000 lm ± 10 % (100 % brightness), 1,000 lm ± 10 % (50 % brightness), 500 lm ± 10 % (25 % brightness)
• Service life:                                  50 000 h
• Beam angle:                                 105° ± 10 % in front of the max. projection surface
• Dimmable:                                  no
• Battery type:                               Li-Ion, 6 600 mAh
• Protective glass:                          Plastic (PC), thickness 0.44 inch (11.24 mm), diameter 1.5 inches (38 mm)
• Protection:                                  IP 65 – Complete protection against penetration of solid bodies as well as dust and protection against hose water.
• Power bank output voltage:        5 V, max. 1 A

USB power adapter

• Model:                                      RSS1002-050050-W2-W
• Input voltage:                           100-240 V AC; 50/60 Hz; 0.2 A
• Output voltage:                         5.0 V DC; 1000mA
• Protection class:                        II

Disposal

Disposing of packaging
Please dispose of package in an environmentally friendly way.

Disposing of the product
If the product should no longer work at all, please make sure that it is disposed of in an environmentally friendly way and according to local regulations.

Batteries and rechargeable batteries may not be disposed of with household waste!
As the end user, you are required by law to bring all batteries and rechargeable batteries, regardless whether they contain harmful substances* or not, to a collection point run by the city, county, or state, or to a retailer, so that they can be disposed of in an environmentally friendly manner. labeled with: Cd = cadmium, Hg = mercury, Li= Lithium, Pb = lead.

FCC

FCC PART 15
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may cause harmful interference, and (2) this device must accept any interference received, including interferences that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B ISM equipment, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experience radio/TV technician for help.

Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>