Ningbo Haishu Di Bi Audio ARIES CP2 Party Speaker User Manual
- June 6, 2024
- Ningbo Haishu Di Bi Audio
Table of Contents
Ningbo Haishu Di Bi Audio ARIES CP2 Party Speaker
INTRODUCTION
Thank you for purchasing the NBVOICE PARTY SPEAKER ARIES CP2. Please read this manual carefully, and keep it safe if in feature reference.
CONTROL PANEL
-
AUX IN
Accepts 3.5mm Minijack input connections. -
USB SLOT
Play media files from a USB device by connecting the device to the solt. -
TRELBE
Increase and decrease the low frequency for MIC/LINE/AUX/MP3 sources at a range between -10dB to +10dB. -
BASS
Increase and decrease the high frequency for MIC/LINE/AUX/MP3 sources at a range between -10dB to +10dB. -
M-REVERB
Increase the echo effect of the microphone sound, and make people live more full. -
M-ECHO
Adjust the knob to make the microphone sound more pleasant. -
GT-VOL
Adjust the volume of the guitar. -
M-VOL
Adjust the volume of the microphone. -
MICROPHONE
Accept 1/4’’ microphone jack in. -
GT
Accept 1/4’’ guitar jack in. -
POWER
Power switch button -
AC IN
Plug in the adapter to charge.
The media player can play audio tracks stored on a USB memory stick or stream audio from your Bluetooth-enabled device. -
MODE
Press this button to switch USB or Bluetooth mode. -
PREVIOUS
Press this button to play the previous song. -
PLAY MODE
Press repeatedly to cycle through the available play modes:- All. Plays all tracks on loop, regardless of folder.
- Repeat one. Plays the current track on loop.
- Random. Plays tracks from all folders in random order.
- Repeat folder. Plays all tracks in the current folder on loop.
-
MIC PRI
Eliminate the singer’s voice in the music, allowing you to sing freely. -
NEXT
Press this button to play the next song. -
PLAY/PAUSE
Plays or pauses the USB or Bluetooth media. -
SCENE SWITCHING
Switch the sound mode, outdoor or indoor. -
CHRACK
There are four voice changing effects. The sound from the microphone can be changed to a different sound. -
LCD DISPLAY
Display the media panel modes for USB&Bluetooth. -
MASTER
This knob controls the speaker all of output volume.
Remote control
Inserting the battery into the remote control Press the lock of the battery holder to the centre of the housing and pull out the battery holder like a drawer. Insert the battery. The battery is correct if the positive pole points to the housing base of the remote control. Slide the battery holder back into the remote until it clicks into place. When shipping, the battery is already installed in the remote and protected against discharge by a transparent plastic foil. Remove the plastic foil prior to first use
Bluetooth connection method
-
Open the bluetooth speaker bluetooth
Long press -
In the mobile phone set Open the equipment bluetooth phones Find ARIES CP2 click ARIES CP2 pairing.
Warning Statement
.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>