HiteVision AX1802-GT Network Module for Conference Display User Manual
- June 6, 2024
- HiteVision
Table of Contents
《Operation Manual of WLAN Module》
| VER： | V2.0 |
|---|---|
| Product name： | Network Module For Conference Display |
| Model No. | AX1802-GT |
Fictioner: Liu Zhi Yong
Checker: Zhang Chao Bing
Approver ：Zeng Xiang Long、Tan Yi
Date： 2022. 02 . 10
Product Description
The product described in this document is the basic information of network module hardware, and the unified model name of network module is AX1802-GT. This module mainly establishes the network foundation for the large screen customer environment of commercial display. The products respectively support wired and wireless wan to realize data access to the external network, and provide high-speed and stable wireless hot spots to meet the terminal wireless internet access and business needs.
Basic information of network module products
- Hardware interface and function
Without Bluetooth
Interface distribution:
| Port Name | Function Explain |
|---|---|
| 80pin-connector | It is mainly connected with Android main board through 80pin- |
connector to realize module power supply (voltage 12V). At the same time, it
integrates three LAN ports to realize LAN data transmission
Port: Intelnet| One support 10 \ 100 \ 1000m Ethernet port, realize WAN port
data access function
Port: LAN| One support 10 \ 100 \ 1000m Ethernet port, realize LAN port data
access function
Wifi-Antenna| Support 2.4 G & 5 G radio frequency signal output, the biggest
gain 5 dbi; As a wireless hotspot, the product provides wireless
access/transmission services for terminal equipment;2 * 2 MIMO antenna with
the highest link rate of 867mbps
Product block diagram description
- The product is a plug – in network module, dedicated for honghe commercial display large screen. The power supply and outage of the module are provided by the internal power bus of the display screen.
- The product is a plug – in network module, dedicated for honghe commercial display large screen. The rf antenna of the product module is divided into external antennas. The antenna is an integral and non-detachable structure.
Built in diagram of network module：
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/Canada. This device is intended only for OEM integrators under the following conditions:
- The antenna must be installed such that 20 cm is maintained between the antenna and users, and
- The transmitter module may not be co-located with any other transmitter or antenna,
Important Note:
This modular transmitter is only FCC authorized for FCC Part 15.247&15.407 as
listed on the grant, and the host product manufacturer is responsible for
compliance to any other FCC rules that apply to the host not covered by the
modular transmitter grant of certification. The final host product still
requires Part 15 Subpart B compliance testing with the modular transmitter
installed.
End Product Labeling
If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: 2ACYT-AX1802
Information that must be placed in the end-user manual:
The OEM integrator has to be aware not to provide information to the end-user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module. The end-user manual shall include
all required regulatory information/warning as show in this manual.
OEM integration instructions:
This device is intended only for OEM integrators under the following
conditions: The transmitter module may not be co-located with any other
transmitter or antenna. The module shall be only used with the external
antenna(s) that has been originally tested and certified with this module. As
long as the conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed (for example, digital device emissions, PC peripheral
requirements, etc.).
Validity of using the module certification:
In the event that these conditions cannot be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC
authorization for this module in combination with the host equipment is no
longer considered valid and the FCC ID of the module cannot be used on the
final product. In these circumstances, the OEM integrator will be responsible
for re-evaluating the end product (including the transmitter) and obtaining a
separate FCC authorization.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>