BY JASCO JPY3176 LED Puck Lights User Manual

: June 6, 2024
: BY JASCO

Table of Contents

INSTALLATION
OPERATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BY JASCO JPY3176 LED Puck Lights User Manual

BY JASCO JPY3176 LED Puck Lights User Manual

INSTALLATION

Carefully plan out your installation prior to securing your lights to the mounting surface, making sure that your 5ft. line cord will reach the nearest electrical outlet.
For kitchen installations, the recommended mounting surface is near the front lip of your kitchen under cabinets. This will provide the best light distribution across a countertop.

STEP 1: CHOOSE INSTALL LOCATION
Before installing, select a suitable mounting location that is dry and capable of supporting the pucks. Make sure that there is plenty of room for the included 5ft. power cord to reach the nearest outlet.
DO NOT ATTEMPT TO INSTALL LED PUCK LIGHTS WHILE PLUGGED IN.

STEP 2: MARK SCREW LOCATIONS
On either side of the puck are keyhole tabs. Using these for guidance, hold the puck in place and use a pencil to mark the location for the screws.

STEP 3: PRE-DRILL HOLES
Using the pencil marks for guidance, predrill holes in the mounting surface with a 1/16in. (1.5mm) drill bit for soft woods and a 3/32in. (2.4mm) drill bit for hard woods.

STEP 4: INSERT SCREWS
Insert the screws with a #1 Phillips screwdriver, leaving 1/8in. beyond the surface.

STEP 5: MOUNT PUCKS Align the keyhole tabs with the screws and slide the puck into place. Tighten the screws as needed.

OPERATION

STEP 6: CONNECT WITH LINKING CORDS Insert the 3-pin connector on the power cord into the fixture and the flat plug into the nearest 120VAC 60Hz outlet.

STEP 7: PLUG IN TO POWER The included power cord has a flat plug on one end and a 3-pin connection point on the other. Plug the 3-pin connector into the nearest puck in the sequence and the flat plug into a 120VAC 60Hz outlet.

LOW/OFF/HIGH SWITCH Use the switch on the side of each LED puck to change between OFF, low-level white light and high-level white light. Each puck in the sequence is independently controlled.

LINKING ADDITIONAL FIXTURES: To add more light pucks (sold separately), simply follow the steps above. Keep in mind the distance between each puck and not to exceed the maximum of 20 LED light fixtures per outlet. The sequence is independently controlled.

WARNINGS TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS:
This fixture has a polarized plug (one blade is wider than the other) to reduce the risk of electric shock. This plug will fit into a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never use an extension cord unless the plug can be fully inserted. Do not alter the plug.

Read the entire installation procedure before you begin.
Not to be used with a dimming circuit or any other electronically switched control.
Do not attempt to install the fixture while plugged in.
Save these instructions so you can refer to them at a later time.

CLEANING INSTRUCTIONS: Your fixture is made from quality materials that will last for many years with minimum care. When cleaning, make sure you have unplugged your fixture and allowed sufficient time for the unit to cool to room temperature. You should clean the housing and lens using a soft, damp cloth. You should plug your fixture back in only after the fixture has thoroughly dried.

FCC STATEMENT: Suppliers Declaration of Conformity | Model #: 54849 54937 | Jasco Products Co., 10 E. Memorial Rd., Oklahoma City, OK 73114, www.byjasco.com

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.

WARNING

RISK OF ELECTRIC SHOCK
DO NOT USE IN WET LOCATIONS.
USE INDOORS ONLY.
USE ONLY INSULATED STAPLES OR PLASTIC TIES TO SECURE THE CORDS.
ROUTE AND SECURE THE CORDS SO THAT THEY WILL NOT BE PINCHED OR DAMAGED.
NO SERVICEABLE PARTS
NON-REPLACEABLE LEDS
LED LIGHT OUTPUT IS STRONG ENOUGH TO INJURE HUMAN EYES. PRECAUTIONS MUST BE TAKEN TO PREVENT LOOKING DIRECTLY AT THE LEDS WITH UNAIDED EYES FOR MORE THAN A FEW SECONDS.
RISK OF FIRE
NOT INTENDED FOR ILLUMINATION OF AQUARIUMS.
NOT INTENDED FOR USE ABOVE STOVES, COOK TOPS, SINKS OR OTHER HEAT PRODUCING APPLIANCES, SUCH AS COFFEE MAKERS, TOASTERS, OR TOASTER OVENS.
NOT INTENDED FOR RECESSED INSTALLATION IN CEILINGS OR SOFFITS.
NOT INTENDED FOR SURFACE INSTALLATION INSIDE OR ON TOP OF BUILT-IN FURNISHINGS SUCH AS KITCHEN CABINETS, CHINA CABINETS, OR TROPHY CASES.
DO NOT CONCEAL POWER SUPPLY CORD OR LINKING CORDS INSIDE A WALL, CEILING, SOFFIT, KITCHEN CABINET, OR SIMILAR PERMANENT STRUCTURE.
DO NOT RUN THE POWER SUPPLY CORD OR LINKING CORDS THROUGH HOLES IN WALLS, CEILINGS OR FLOORS.

MADE IN CHINA GE is a trademark of General Electric Company andis under license by Jasco Products Company LLC,10 E. Memorial Rd., Oklahoma City, OK 73114. This Jasco product comes with a limited-lifetime warranty. Visit www.byjasco.com for warranty details.

Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483 between 7AM-8PM, M-F, Central Time.
54849 54937 v2 02/21

byjasco.com/recycle

BY JASCO JPY3176 LED Puck Lights User Manual - Thank you
Page