Shenzhen Rigic Wit Control Technology PGL01 Smart Plant Grow Light User Manual

Shenzhen Rigic Wit Control Technology PGL01 Smart Plant Grow

Light

Installation Instructions

Installation Method

• Opt1ong- paste the Lamp
• Opt1on2-install by ZIP toes(cable ties)
• Opt1onJ-Mount to Ce1llng

Operating Instructions

Install Smart Life APP

• Please scan the QR code with a mobile phone, and install the app according to the instruction
• Please scan the QR code with a mobile phone, and install the app according to instruction

Adding New Device

Enter network figuration mode. Steps: Quickly turn on and off the controller power 5 times, power on 2S and 4S count as 1 time, after power on for the 5th time, keep the power on and wait for 5S-10S. When LED Grow Light flashes quickly, it indicates that the controller has successfully entered the network figuration mode

• Connect to WIFI network, turn on Bluetooth and GPS function
•  Open app “Smart Lift”, click the “ ”button on the upper right corner to add the new device
• When the app found new devices, click “Go to add” to add this device
•  Choose WIFI name and input password
• Waiting for 1-2min for the device to distribute network
• After the network is distributed successfully, click “NEXT”
• Click“ ”to edit the name for the new device, and click “save”
• A new device is added successfully

Operation of LED Grow Light app

Slide “Bright” to adjust the brightness of the LED Grow Light

Select the ratio in the “Matching ratio selection” table to choose different ratios of red light and blue light, so as to adapt to the light source needed by plants in different periods

• Rhizome plants: recommended ratio of red and blue light 0:1—:3:1
  For example carrots, yams, sweet potatoes, potatoes, onions, and so on

•  Cauline plant: recommended ratio of red and blue light1:1—5:1

• Succulent plants: recommended ratio of red and blue light 3:1—7:1
  For example cactus, Echinopsis tubiflora, Sedum rubrotinctum, Plectranthus hardiness var. tomentosus, Golden Finger, Thor, Jewel Flower。

• Flowering and fruiting plants: recommended ratio of red and blue light7:1—8:1 or 1:0 For example pepper, eggplant, cucumber, bitter gourd, tomato, strawberry

• Click” “to turn on LED Grow Light, click” “to turn off LED Grow Light, click” “to check the instructions

• Click” “to set a timer for the LED Grow Light to be turned on or off

  • Repeat is used to choose repeated timer choice
  • Note is used to record
  • Notification is used to perform notification
  • ON/OFF is used to set a timer, to decide to turn on or off when the timer ends

Remove Device
Method 1: click” “, then scroll down to the bottom and click “Remove Device”

Method 2: Quickly turn on and off the controller power for 5 times, power on for 2S and off for 4S counted as 1 time, after power on for the 5th time, keep the power on and wait for 5S-10S. When LED Grow Light flashes quickly, then it indicates that the controller has successfully exited the network, and at the same time the device is in-network distribution mode

Note

•  Please handle with care, don’t press and don’t drop it;
• When installing lamps, the wiring should be insulated to prevent leakage of electricity；
• Can not be used in flammable, explosive, high temperature and corrosive places
• In case of malfunction, repair or replacement must be processed by professionals

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>