KAUBER B07ZXZZGM6 CLR Projection Screen Installation Guide

KAUBER B07ZXZZGM6 CLR Projection Screen

IMPORTANT!!! INSTALLATION AND OPERATION NOTES

1. The screen should be installed in a place away from moisture and strong sunlight.
2. Use the gloves provided in the kit to mount the surface and install the screen.
3. Clean with a soft microfiber cloth, lightly moistened with soap dissolved in water. Due to the structure of the surface, wipe only with horizontal movements, do not make up and down movements. Do not use active cleaning agents. After cleaning, the screen should be carefully wiped dry to remove any residual moisture.
4. Correctly mounted screen must be absolutely level in every plane.
5. DIMENSIONAL TOLERANCE: Projection surface: ± 0.5% of the nominal size; components ± 5 mm. IMPORTANT: Any mechanical damage to the surface voids the warranty.

SCREEN MOUNTING

1. Place all frame parts on a clean and level surface. Insert the steel angles into the profile of the screen frame, as shown in Fig. 1, previously placing square washers in each profile as in Fig. 2. NOTE! Insert 4 additional washers into the upper profile of the frame, which will be used to install wall brackets Fig. 2.

2. Slide the second frame to make a right angle, then use the included “B” bolts to attach the angle to the screen frame (Fig. 3). Adjust the screen profiles to obtain a right angle and tighten the “B” bolts (Fig. 4).

3. If the frame profiles form a uniform plane, use the “A” bolts to calibrate the profile by tightening the bolts to obtain a maximum even plane (Fig. 5), leaving room for the bolts (Fig. 6), which will be used to fix the black frame profiles in the next step.

4. Unwind the surface gently with the black side up on the included sponge, as in Fig. 7. Remember that the surface is intended for directional projection. Pay attention to the correct direction when connecting to the frame, so that the top of the surface corresponds to the top of the frame.

5. Gently place the folded frame on the projection surface, so that the corners of the frame and the surface look the same on each of the corners (Fig. 8).

6.  Remember that the profile of the frame with 5 washers inserted is at the top of the screen, make sure the frame and the surface are positioned correctly (Fig. 9).

7. Start fixing the surface from the corners of the frame by fastening the springs opposite to each other (left-right side of the screen) Fig. 10, Fig. 11, making sure that the surface is evenly stretched.

8. Use a bolt to fix the surface in the center of each side of the screen to the previously placed square washer (Fig. 12, Fig. 13).
   NOTE! This step is only to keep the washer in position, do not tighten the bolt, just insert it slightly. It will help avoid the displacement of the washer during further assembly.

9. Fix the surface with springs starting from the corners of the screen going towards the center, starting from the shorter sides. Make sure the surface is evenly stretched. NOTE! The springs should be fastened by two people, so as to simultaneously fasten the springs opposite to each other. After installing a few springs, the frame can be slightly lifted to relieve surface tension.

10. Invert the screen slightly and check whether the surface is stretched evenly and there is no deformation. If there is such an occurrence, gently move the surface with your hand from the centre towards the corner. Fig. 14.
    IMPORTANT: the area where you can touch the surface is 10 mm from the edge of the screen (Fig. 14).

11. Place the black profile on the outer part of the frame by unscrewing the center fixing of the surface made in step 9., proceeding as shown in Fig. 15 to Fig. 18.
    NOTE! After placing the profiles in Fig. 17, slightly lift the screen, so as to reduce the distance between the bolt and the screen profile.

12. Fix the wall brackets to the frame, using the washers in Fig 19. Remember that it is possible to mount the brackets inside the screen, then the mounting system will not be invisible Fig 20.

13. Attach the included magnet (Fig. 21) to the bottom profile of the frame (Fig. 22), at a maximum distance of 20 cm from the edge of the frame.

14. The set includes two plates for wall mounting, in order to eliminate the protrusion of the bottom corners of the screen from the wall (Fig. 23).
    Advice! Pull off the suspended screen frame at the bottom and attach the metal plate (Fig. 23) to the magnet (Fig. 21). Move the screen as close to the wall as possible. Then, mark the shape of the plate on the wall, which will serve as a template for fixing it (Fig. 24).

TECHNICAL DATA

Housing dimensions:

FRAME

• A- surface width
• B- surface height
• C- A + 10 mm
• D- B + 10 mm
  Screen depth after assembly 48 mm

Thank you for choosing the KAUBER screen We invite you to buy other KAUBER products

Visit: www.kauber.eu 

References

• KAUBER :: Fully customizable screens

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>