Schneider Electric SQR621U1WHW Wi-Fi Plug-in Energy Monitoring Complement Instructions
- June 6, 2024
- Schneider Electric
Table of Contents
Instruction Bulletin
SQR621U1WHW Wi-Fi® Plug-in, Energy Monitoring
Complemento Wi-Fi® SQR621U1WHW
Prise pour duplex SQR621U1WHW Wi-Fi®
Retain for future use
Introduction
- You can control lights, fans, humidifiers, Air conditioners, and any small appliances in accordance with the Smart Plug’s specifications.
- Reduce energy consumption and enjoy Wireless Home Automation
- You can turn your devices on or off at any time or anywhere have Internet using the free SE Wiser App on your smartphone
- Wi-Fi® is a registered trademark of Wi-Fi Alliance R
Specifications
| Cat.No. | SQR621U1WHW |
|---|---|
| Voltage | 125 Vac, 60 Hz |
| Incandescent | 800 W |
| LED | 5 A |
| Rated Impulse voltage | 1500 V |
| Resistive | 1800 W (15 A) |
| Motor | 1/2 Hp |
| Operating Temperature | 32-104°F(0-40°C) |
| Supply Connection | 14AWGwires, suitable for at least167°F(75°C) |
| Wireless Type | Wi-Fi®, IEEE 802.11b |
| Wireless Frequency | 2.4 GHz |
Precautions
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
- Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E, NOM-029-STPS or CSA Z462, or local equivalent.
- Do not touch metal pins during plug-in or out.
- Indoor use only. Failure to follow these instructions will result in death or serious injury.
WARNING
HAZARD OF HEAT AND FIRE DAMAGE
Read all instructions before installation. The manufacturer will not be held
responsible for product damage resulting from not following the instructions.
- Wet hands are strictly prohibited.
- Work strictly according to the rated load.
- Do not continue working after self-disassembly of any nature and damage by external forces.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
CAUTION
HAZARD OF UNINTENDED USE This Z-
Wave plug-in is intended to be used for non-critical automation activities. It
is not intended to support life, safety, or medical equipment.
Failure to follow these instructions can result in personal injury or
equipment damage.
WARNING: This product can expose you to chemicals including Carbon-black
which is known to the State of California to cause cancer, and Bisphenol A
(BPA), which is known to the State of California to cause birth defects or
other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
Operation
1. Local control:
NOTE: After a power loss the switch returns to the off state.
Figure
2. SE Wiser App Control
2. 1. Download the Wiser by SE app from the App Store or Google Play.
QR code for iOS App download
QR code for Android App download
2. 2. Connect your mobile device to your 2.4GHz Wi-Fi® network. Please note
this Smart Dimmer Switch can only be connected to a 2.4GHz network.
Please Note: When power is reconnected after the interruption, the LED
indicator in green will flash quickly which means that the Dimmer is searching
for Wi-Fi®. It will stop flashing and turn off when Wi-Fi® is connected
successfully for 5 seconds. when the LED indicator is solid green means your
network anomaly, pls check the network.
snoitidnoC egnaR sseleriW
The wireless range is the effective distance of remote control and it will be
impacted by the following conditions:
- Each wall or obstacle (e.g., refrigerator, TV, etc.) between the remote or device and the destination device will reduce the wireless range.
- Brick, tile, or concrete walls block more of the wireless signal than walls made of wooden studs and plasterboard (drywall).
- The angle of direction between the remote or device and the destination device will also impact the wireless range; normally, placing the devices face-to-face will get the best wireless range
- Wall-mounted devices installed in metal junction boxes may suffer a significant loss of range since the metal box blocks a large part of the wireless signal.
LED Indication
| Indication | State | Description |
|---|---|---|
| AP | The LED indicator shall start single blinking. |
| Connected| The LED
indicator will be turned to solid once the cloud connectivity is established.
The on-state shall last for up to 1 minute.
| Offline| Once the device is offline, it shall enter a double blinking
pattern for 3 minutes. After, the indicator shall track load status.
| Operating| The LED
indicator shall track the load on/off status. By default, when the load is on,
the LED should be on, and vice versa. Notice the tracking state could be
Restoring Procedure
| L0 reset: Wi-Fi function reboot. | Long press (T > 5s) the on/off/reset button. |
|---|---|
| L1 reset: Leave network; Re-enter AP mode. | Long press (T > 10s) the |
on/off/reset button.
L2 reset: Leave network and clear all configurations.| Long press (T > 20s)
the on/off/reset button.
FCC Compliance Statement
Federal Communication Commission Interference Statement
The equipment has been tested and found to comply with the limits for a Class
B Digital Device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment uses, generates, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instruction, may cause harmful interference to radio communication. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
RF Exposure: A distance of 20 cm shall be maintained between the antenna
and users, and the transmitter module may not be co-located with any other
transmitter or antenna.
Non-modification statement
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
FCC Supplier’s Declaration of Conformity
Product Name: Wi-Fi® 15A PLUG-IN OUTLET
Model number: SQR621U1WHW
Suppliers Name: Schneider Electric
Suppliers Address (USA): 800 Federal Street Andover, MA 01810 USA
Suppliers Website : www.se.com/us
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
ISED Statement
This Class [B] digital apparatus complies with Canadian CAN ICES-003(B).
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may
cause undesired operation of the device.
This equipment complies with ISED RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20 cm between the radiator and any part of
your body.
Model numbers: SQR621U1WHW
Warranty Information
Schneider Electric warranties its products to be free of defects in materials and workmanship for a period of two (2) years. There are no obligations or liabilities on the part of Schneider Electric for consequential damages arising out of or in connection with the use or performance of this product or other indirect damages with respect to loss of property, revenue, profit, or cost of removal, installation, or reinstallation.
Electrical equipment should be installed, operated, serviced, and maintained
only by qualified personnel. No responsibility is assumed by Schneider
Electric for any consequences arising out of the use of this material.
Schneider Electric and Square D are trademarks and the property of Schneider
Electric SE, its subsidiaries, and affiliated companies. All other trademarks
are the property of their respective owners.
Schneider Electric USA, Inc. 800 Federal Street Andover, MA 01810 USA
888-778.2733 www.se.com/us
© 2020 Schneider Electric All Rights Reserved
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>