Parani A20 Bluetooth Intercom Headset User Manual
- June 6, 2024
- Parani
Table of Contents
A20 Manual
Charging
Power On/Off
(+) Button + Multi-function Button for 1 sec
Volume Adjustment
(+) Button – Increase the volume
(-) Button – Decrease the volume
Phone, Music Pairing
Initially Pairing the A20
The Bluetooth system will automatically enter the phone pairing mode when you
initially turn on the Bluetooth system or in the following situation:
• Rebooting after executing Factory Reset
- Press and hold the Multi-function button and (+) Button for 1 second.
- Search for Bluetooth devices on your mobile phone. Select the Parani A20 in the list of the devices detected on the mobile phone.
- Enter 0000 for the PIN. Some mobile phones may not ask for the PIN.
Music Operation
Play or pause music: Press the Multi-function Button for 1 second.
Trackback: Press the (-) Button for 1 second.
Track forward: Press the (+) Button for 1 second.
Mobile Phone Call Making and Answering
Answering a call: Tap the Multi-function Button
Ending a call: Press the Multifunction Button for 2 seconds.
Voice dial: Press the Multi-function button for 3 seconds.
Speed dial: Press the (+) Button for 3 seconds.
Rejecting a call: Press the Multifunction Button for 2 seconds.
Intercom Pairing
- Press and hold the Multi-function Button of two Bluetooth systems for 5 seconds until the red LEDs of both units start to flash rapidly.
- Simply tap the Multi-function Button of any one of the two Bluetooth systems.
Intercom Start/End
1st Friend: Tap the Multi-function Button once.
2nd Friend: Tap the Multi-function Button twice.
3rd Friend: Tap the Multi-function Button triple times
Radio On/Off
\Turn on the FM radio: Press the (-) Button for 1 second.
Turn off the FM radio: Press the (-) Button for 1 second.
Radio Seek Stations
Seek up stations: Double-tap the (+) Button.
Seek down stations: Double-tap the (-) Button.
Setting
configuration Menu: Press the Multi-function button for 15 seconds.
Troubleshooting
Factory Reset
If you want to restore the Bluetooth system to factory default settings, use
the Factory Reset in the configuration menu. The Bluetooth system
automatically restores the default settings and turns them off.
Certification and Safety Approvals FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment on and
off, the user is encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antennae
-Increase the separation between the equipment and the receiver
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End-users must follow the specific operating
instructions for satisfying RF exposure compliance. The antenna used for this
transmitter must not transmit simultaneously with any other antenna or
transmitter, except in accordance with FCC multi-transmitter product
procedures.
When equipped, the distance between the antenna and one’s head surface is
38mm.
FCC Caution
Any changes or modifications to the equipment not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment.
Industry Canada(IC) Statement
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1)this device may not cause interference, and
(2)this device must accept any interference, including interference that may
cause undesired operation of the device.
Le present appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisee aux deux
conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioelectrique
subi, meme si le brouillage est susceptible d’en compromettre le
fonctionnement.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>