RaySharp RS-CH728H4C-WA28PW Wireless Camera User Guide
- June 5, 2024
- RaySharp
Table of Contents
Quick Start Guide
HD Network Camera
Wireless Camera
RS-CH728H4C-WA28PW
1 Camera Connection Diagram
Attention:There are two connection modes:
- For non-PoE router,pls connect the camera by a PoE switch or a PoE injector.
- For a POE NVR,pls connect the camera directly to the POE NVR, then follow the below steps.
2 Installation
Bullet Camera Installation
Ceiling Mounting
- Mounting Screws
- Expansion Bolt
Insert three expansion bolts in place into the ceiling and fix the equipment with three mounting screws.
Completion of Installation
Dome Camera Installation
Ceiling Mounting
Dome Camera
- Setup of Sticker
Paste the sticker in place at the proper position as selected.
- Collar
Remove the collar off the camera by rotating it down
- Locking Screw
- Expansion Bolt
Fix the pedestal by drilling locking holes around the sticker and inserting three expansion bolts into the holes and fastening it with three locking screws.
Mount the collar back by rotating it up
Adjust it to an appropriate angle.
Completion of Installation
Vandal-Proof Dome Camera Installation
Ceiling Mounting
- Position Sticker
Apply the position sticker to the desired camera mounting position.
Cover Component
Remove the cover component by loosening the three locking screws with the
included hex wrench.
- Expansion Bolt
- Mounting Screw
Use the position indicated on the position sticker to drill the holes needed to mount the camera base. Insert the expansion bolt into the holes. Match the base’s mount openings to the expansion bolts position, then place the mounting screws through the base’s mount opening into the expansion bolt. Tighten the mounting screws to ensure the camera base mounted securely.
Completion of Installation
- Locking Screws
※ Place the cover component back onto the base.
※ Please make sure the locking screw position on the cover component matches
the locking post on the base.
※ Tighten the locking screws after the cover component is in the correct
position.
3 Install the APP
There are two methods to install the App.
- Search for “RXCamView” in App Store or Google Play.
- Scan the QR code below to download the App.
For IOS For Android 08
4 Camera Settings
Open “RXCamView”, you will see the following interface to add the cameras.
If add the device successfully, you will see the following interface.
※ Please refer to “Help” section for more detailed instruction.
5 In Windows
1. log in the website www.al8.co and click “Device Search for Windows” to download “Device Config Tool”, it will help to search all the available devices on your local network.
2. Under “Device Config Tool”, you can modify the information of a selected device. Including IP, Media Port, Web Port, Gateway, Net Mask, Net Mode. (The default username & password is: admin & admin)
3. Open the Internet Explorer and input the device’s IP address;
Input the username & password in the following interface to login the device.
4 After login click Remote Setting” to change the setting.
6 In MAC OS
1. Open your router web interface and login.
2. Find the “Attached device” or “Connected device” menu.
Find the device’s IP address according to it’s MAC address.
The Mac address is labeled on the device.
Picture for reference only
3. Input the device’s IP address in Safari, login with your username &
password.
4. After login, click “Remote Setting” to modify the setting.
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>