Promix SM308 Electromechanical Lock with Pusher And Door Position Sensor User Manual

SM308 Electromechanical Lock with
Pusher And Door Position Sensor
User Manual

PURPOSE

Electromechanical locks series Promix-SM308 with a hook-shaped locking mechanism (below called the locks) are intended for restriction of access to cells of luggage lockers  (post offices), drawers for storage of documentation, lockers, and cabins in locker rooms of fitness clubs, swimming pools, schools, factories; the locks can be opened remotely.

LABELING

The label stuck to the lock body contains the following information:

1. Lock model.
2. Patent number.
3. Nominal supply voltage.
4. Nominal consumed current.
5. Date of manufacture and QCD mark
6. Identification number.
7. Manufacturer’s website.

For the list of lock modifications that can be ordered, see 5.2.
The color of the product is shown on the sticker stuck to the box, after the product name. Series colors: Silver, White, Brown, Black. Other colors are provided optionally.

SET OF DELIVERY

Check the completeness of the lock set when buying! After buying, the manufacturer will not accept claims related to an incomplete set.

DESIGN AND PRINCIPLE OF OPERATION

The lock Promix-SM308 is produced in a normally closed version, i.e., it is in the closed state when de-energized and opens as the supply voltage is applied.
The lock is mounted on the inner surfaces of the locker transversely to the door and is operable in both vertical and horizontal positions. The mating part (latch) is mounted on the  door.
As the door is closed, the latch is inserted in the lock and becomes blocked therein. As supply voltage is applied, the lock deblocks the latch and pushes it with a built-in pusher,  which allows eliminating mounting of a handle on the door.
The spring-loaded pusher of the lock is connected to the door position sensor. The operating principle of the sensor is described in 6.3.

TECHNICAL DATA

OPERATING CONDITIONS
The lock operation environment must be explosion-safe, free of current- conducting dust or gases that cause metal corrosion and destroy insulation of current conductors and electric elements, free of current-carrying dust or water vapor, and preventing ingress of water, steam, fuel, and lubricants.
Climatic conditions of operation – У3.1 as per GOST 15150-69 with extended temperature range:

• ambient temperature: from -30 to +50 °С;
• Relative air humidity: not higher than 98% at 25°С or lower temperatures without moisture condensation and hoar-frost formation;
• installation indoors or outdoors excluding ingress of moisture, dust, dirt, etc. inside the lock.

TECHNICAL DATA

Modification

| Promix-SP11308.10.1| **Promix-SM308.11.1***
---|---|---
Version|

normally closed

DC supply voltage U, V

| 12±2| 24±2
Current consumed, A| 0.4 (at 12V)|

0.27 (at 24V)

Supply pulse duration (not more than), s

| 1-10
Minimum pause between pulses, s| 15

|

20

Built-in sensors

|

door position sensor

Maximum switch current of the sensor (DC), A:

| 0.2
Maximum switch voltage of the sensor (DC), V:|

24

Sensor output signal type

| “dry contact”
Lock weight (not more than), kg|

0.27

Holding force (not less than), kg

| 250
Initial latch pushing out force (not less than), kg|

1.2

• – Manufactured against the order
  Lock and latch overall and mounting dimensions.

INSTALLATION AND CONNECTION

LOCK AND LATCH MOUNTING

1. Screw out the screw on the front surface of the lock and remove the cover.

2. Mount the lock on a wall, at a distance of 15mm from the locker wall edge.
   

3. Connect the lock to the power supply (see 6.3).

4. Insert the latch into the lock.

5. Test operability of the lock – as the voltage is applied, the lock must push out the latch.

6. Fasten the latch to the door at a distance of 20±3mm from the base edge of the lock (see Fig. below).
   

7. Test operability in door closing.

EMERGENCY OPENING OF THE LOCK
For the emergency opening of the lock, insert a wire (e.g., a paper clip) and, having caught the part “lever” (see the Figure below), move it until the lock operates.

CONNECTING PROCEDURE
The lock operation is controlled by means of energizing and de-energizing. For this purpose, a controller (control board) or a switch (button) is generally used. The controller is mounted in accordance with its certificate.

Purpose of terminals:

1. Lock energizing.
2. Normally open contact of the sensor.
3. Common contact of the sensor.
4. Normally closed contact of the sensor.

Connect the lock power wires adhering to the following polarity:
Terminal 1 – positive pole of the power supply;
Terminal 2 – negative pole of the power supply;
Application of voltage of reverse polarity does not provide the lock operability but does cause its failure.

When the pusher is embedded in the lock (the door is closed), the output contacts 3-4 of the sensor are closed 3-4 (5-4 are open); when the pusher is shifted out of the lock (the door is open), the output contacts 3-4 of the sensor are open (5-4 are closed).

See operating voltage range in 5.2. Avoid supply of overvoltage.
Example of the lock connection to the remote control system Promix-RDS.

Provide a reliable electric contact. To prevent short-circuiting, insulate places of connection.

SPECIAL ASPECTS OF INSTALLATION AND OPERATION

1. The possibility of using the lock and the place of installation (outdoors or indoors) are determined by the installation organization on the basis of the design features and the lock operating principle, method of installation, room criticality level, the purpose of the access restriction regime and other factors (the presence of security providers,  video surveillance, etc.).
2. To prevent deformations of the door due to attempts to open the door with the lock closed, it is recommended to mount the lock in the area of the door handle.
3. It is recommended to install the lock together with a door closer – this reduces the impact load on the lock and extends its service life.

TROUBLE-SHOOTING

Check the absence of supply voltage.
Adjust the latch position (see 6.1) so that the latch, with the door closed, enters the lock slot until the catch hook operates.
The latch does not enter the lock slot or enter with friction.| Restore the position of the door that changed in the course of operation. If  restoration is impossible, adjust the latch (see 6.1)

MAINTENANCE

Maintenance of the lock is performed at least once every two months and includes:

• Visual inspection of the lock to check the reliability of fastening. If necessary, tighten the fasteners of the lock and the latch.
• Checking the proper position of the latch. (see section 8).

The lock does not need lubrication!

STORAGE AND TRANSPORTATION

Prior to putting into operation, the locks must be stored in the manufacturer’s packing, in rooms with an ambient temperature of -30 to +50 °С and a relative humidity not higher than 98% at 25º С in compliance with storage conditions as per GOST 15150-69.
Locks transportation conditions must comply with group C as per GOST 23216-78 in terms of exposure to mechanical factors, and Ж2 as per GOST 15150-69 in terms of exposure to climatic factors.

SAFETY REQUIREMENTS

The design of the locks ensures the safety of personnel involved in mounting and maintenance.
Due to low DC supply voltage, the products correspond to class III as per GOST 12.2.007.075 and are electrically safe. Fire safety of the locks is ensured by use of non-combustible or hardly combustible materials, and low supply voltage.

DISPOSAL
The product is not hazardous for human life and health or for the environment; disposal after its service life is performed without taking any special measures for environmental protection.

WARRANTY LIABILITIES

The manufacturer, ETC PROMIX LLC, warrants conformity of Promix-SM308 locks to requirements of current Technical Specifications provided that transportation, storage,  installation, and operation rules established in this Manual are followed.
The warranted operation period is 12 months from the date of sale but not longer than 18 months from the day of acceptance by the manufacturer’s QCD.
Within the period of warranty, ETC PROMIX LLC undertakes to repair defective products free of charge. Expenses for transporting the product to the place of repair and back will be borne by the Buyer.
Warranty liabilities do not cover any defects and damages caused by:

• Improper maintenance by the Buyer;
• Use of the product under conditions that do not comply with the operational requirements;
• Mechanical damages or disassembly of the products by the Buyer;
• Non-observance of the transportation and storage rules.

Faulty products are accepted for repair only together with the latch, on the obligatory condition that factory labels are retained on the product body.
On the expiration of the warranty service period, the manufacturer provides after-warranty service on a contractual basis.
To improve product quality the manufacturing plant reserves the right to make modifications to the product design without prior notice.

ACCEPTANCE AND PACKING CERTIFICATE

Electromechanical lock Promix-SM308 in the quantity of ____ pieces (1 pc. by default) bearing the manufacturing date and QCD mark on the body was manufactured and accepted in compliance with Specifications, obligatory requirements of state standards, and current technical documentation, recognized as fit for operation and packed by ETC PROMIX LLC.

PROMIX Engineering and Production Center LLC
Russia, 214030, Smolensk, Krasninskoye sh., 35, lit. A
Phone: (4812) 619-330
www.promix-center.com
facebook.com/promixcenter
mail@promix-center.com<https ://promix-center.com/electromechanical-locks/>

References

• Electromechanical locks and other products from Promix
• Electromechanical locks and other products from Promix
• Купить Promix-SM308 по выгодной цене от производителя | Электромеханические замки с толкателем и датчиком положения двери Promix-SM308 от Промикс

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>