Schneider Electric Wiser Micro Module Light Switch User Guide

Schneider Electric Wiser Micro Module Light Switch User Guide

Legal Information

The Schneider Electric brand and any trademarks of Schneider Electric SE and its subsidiaries referred to in this guide are the property of Schneider Electric SE or its subsidiaries. All other brands may be trademarks of their respective owners.

This guide and its content are protected under applicable copyright laws and furnished for informational use only. No part of this guide may be reproduced or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), for any purpose, without the prior written permission of Schneider Electric.

Schneider Electric does not grant any right or license for commercial use of the guide or its content, except for a non-exclusive and personal license to consult it on an “as is” basis. Schneider Electric products and equipment should be installed, operated, serviced, and maintained only by qualified personnel.

As standards, specifications, and designs change from time to time, information contained in this guide may be subject to change without notice.

To the extent permitted by applicable law, no responsibility or liability is assumed by Schneider Electric and its subsidiaries for any errors or omissions in the informational content of this material or consequences arising out of or resulting from the use of the information contained herein.

Safety information

Important information

Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service, or maintain it. The following special messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.

 The addition of either symbol to a “Danger” or “Warning” safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed.

 This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that accompany this symbol to avoid possible injury or death.

DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Failure to follow these instructions will result in death or serious injury.

WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE
NOTICE is used to address practices not related to physical injury.

Wiser Micro Module Light Switch

For your safety

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

Safe electrical installation must be carried out only by skilled professionals.
Skilled professionals must prove profound knowledge in the following areas:

• Connecting to installation networks.
• Connecting several electrical devices.
• Laying electric cables.
• Safety standards, local wiring rules and regulations.

Failure to follow these instructions will result in death or serious injury.

DANGER

HAZARD OF ELECTRIC SHOCK

• Make sure that the terminal connection area does not come in contact with the metallic parts of any device installed in the same location.
• Do not short the outputs to neutral.
• The switch contact and live conductor connection must be separated from one another by a 240 VAC basic insulation.

Failure to follow these instructions will result in death or serious injury.

WARNING

HAZARD OF ELECTRIC SHOCK

• Observe the regulations for working on live parts.
• Only actuate the device buttons using insulated auxiliary equipment that meets the requirements of EN 60900.

Failure to follow these instructions can result in death, serious injury, or equipment damage.

About the device

The Wiser Micro Module Light Switch (hereinafter referred to as Puck) combines the advantages of smart switch functionality with ordinary mechanical push- button switches. It transforms a conventional switch into a connected device that can be controlled from the switch or through the Wiser app. It can switch ohmic, inductive or capacitive loads.

NOTE: Do not control any devices that depend on a permanent power supply. Additional features:

• Remote controlled with maximum of 10 mechanical push-buttons.
• Setting a time schedule.

Installing the device

Refer to the installation instructions supplied with this product.

Testing the device

Before using the Puck, manually test the Puck and make sure that it works when connected to the devices.

WARNING

HAZARD OF ELECTRIC SHOCK

• Observe the regulations for working on live parts.
• Only actuate the device buttons using insulated auxiliary equipment that meets the requirements of EN 60900.

Failure to follow these instructions can result in death, serious injury, or equipment damage.

Short press the test button once, the connected device turns On/Off.

Pairing the device

Using the Wiser Home app, pair your Puck with the Wiser Hub to access and control the Puck.
Follow the steps to pair the Puck:

1. On the Home page, tap icon.

2. Tap Devices >   icon and tap Lights > Micromodule > Next.
   NOTE: The next screen shows the joining process of Puck.

3. Select any one of the options to add the device:

   • Short press the setup/reset button 3 times on the Puck with a screwdriver and make sure the LED blinks amber.
   • Short press the push button 3 times.
     NOTE: If the puck is located behind the push button, the status LED is not visible.

4. Wait for a few seconds until the LED turns green. You can also see in the app that the device is joined.

5. Tap Next to enter the name of the device and assign the device to a new room or an existing room.
   The Puck is now listed under All devices.

Configuring the device

Selecting a location for the device

Using the Wiser Home app, add the Puck to any room (such as living room, bedroom, kitchen etc).

1. On the Home page, tap icon.
2. Tap Devices > Micromodule Switch > Location (A) to assign the puck to an existing room or a new room (B) and tap Submit.
   NOTE: Micromodule Switch is the name given to the device by the user. Any name can be assigned when pairing with the Wiser hub.

Renaming the device

Rename the device using the Wiser Home app.

1. On the Home page, tap  icon.
2. Tap Devices > Micromodule Switch > Device Name (A) to rename the device.

Identifying the device

Using the Wiser Home app, identify the Puck among the devices available in a home.

1. On the Home page, tap  icon.
2. Tap Devices > Micromodule Switch > Identify (A).

The status LED blinks red and connected devices blinks On/Off, upon successful identification of the Puck.

3. Tap OK to finish identifying the device.

Removing the device from Wiser system

Using the Wiser app, you can remove the Puck from the system.
Follow the steps to remove the device:

1. On the Home page, tap  icon.
2. Tap Devices > Micromodule Switch > Delete (A).

NOTE:

  * Removing the device will reset the Puck. After reset the LED turns amber indicating that the Puck is ready to pair with another network.
  * If there is a problem while pairing or resetting the Puck, refer to Resetting the device manually.

Using the device

Manual operation

When the puck is connected to a mechanical push button, the connected devices can be controlled manually by short pressing the push-button rocker.
NOTE: Since the puck is installed inside the wall box, the status LED is not visible while using the puck.

Turning On/Off Puck using app

Using the Wiser Home app, you can turn On/Off the Puck remotely.
Follow the steps to turn On/Off the Puck using the app:

1. Go to the Home page, tap All and find the device.
2. Tap (A) icon to turn On/Off puck.

Setting up a schedule

The devices can be fully controlled by schedule. Once the schedule is set, the devices operates at a given time.
Follow the steps to create a schedule:

1. On the Home page, tap icon.

2. Go to Schedules > + icon to create a schedule.

3. Enter the name of the schedule (A).

4. In the TYPE menu, select Lights (B).

5. In the APPLIES TO menu, select Micromodule Switch (C) from the listed devices.

6. Tap Create to setup events.

7. Tap icon to add an event such as STATE (lights On/Off) and WHEN ( sunrise/sunset or specific time range).

8. Tap Set to save the schedule.

Moments

Moment allows you to group multiple actions that are usually performed together. By using the Wiser Home app, you can create moments based on your needs.

Creating a moment

Follow the steps to create a moment:

1. On the Home page, tap icon.

2. Go to Automation > + icon to create a moment.

3. Enter the name of the moment (A).
   TIP: You can choose the cover image that best represents your moment by tapping icon.

4. Tap Add actions (B) to select the list of devices.

5. In the Add actions menu, you can select the devices (C).

6. Once all the device are selected, tap Done.

7. On the Moment creator page, tap on the device to set the condition:
   – Tap to turn on (D)

8. Once all conditions are set, tap Save.
   Once the moment is saved, it is visible on the Automation tab. You can tap on the moment to enable it.

Editing a moment

Follow the steps to edit a moment:

1. On the Home page, tap icon.
2. Go to Automation, locate the moment you want to edit and tap  (A) icon.
3. On the Moment Editor page, you can tap each item to change the settings and tap Save (B).

Deleting a moment

Follow the steps to delete a moment:

1. On the Home page, tap  icon.
2. Go to Automation, locate the moment you want to delete and tap  (A) icon.
3. On the Moment Editor page, tap Delete (B).

Resetting the device manually

Select any one of the options to reset the device to factory default mode:

• Short press the Setup/Reset button 3 times and then long press the Setup/ Reset button once for 10 s on the puck with a screwdriver.
• Short press the push button 3 times and then long press the push button once for 10 s.
  

LED indication

Pairing the device

once per second.
| Pairing mode is active for 30 seconds. When pairing is completed, LED displays green for a few seconds before turning Off.

Resetting the device

Short press the setup/reset button or push button 3 times and hold it down once for > 10 s or < 20 s.| LED blinks red once per second.
| The device is in reset mode. The device then restarts and LED turns amber indicating that the device is ready for pairing.

Troubleshooting

Resetting the device manually, page 15

Technical data

Compliance

Compliance information for Green Premium products

Find and download comprehensive information about Green Premium products, including RoHS compliance and REACH declarations as well as Product Environmental Profile (PEP) and End-of-Life instructions (EOLI).

General information about Green Premium products

Click the link below to read about Schneider Electric’s Green Premium product strategy.

https://www.schneider-electric.com/en/work/support/green-premium/

Trademarks

This guide makes reference to system and brand names that are trademarks of their relevant owners.

• Zigbee is a trademark of the Connectivity Standard Alliance™.
• Apple® and App Store® are brand names or registered trademarks of Apple Inc.
• Google Play™ Store and Android™ are brand names or registered trademarks of Google Inc.
• Wi-Fi® is a registered trademark of Wi-Fi Alliance®.
• Wiser™ is a trademark and the property of Schneider Electric, its subsidiaries and affiliated companies.

Other brands and registered trademarks are the property of their respective owners.

Schneider Electric
35 rue Joseph Monier
92500 Rueil Malmaison
France

+ 33 (0) 1 41 29 70 00
www.se.com

As standards, specifications, and design change from time to time, please ask for confirmation of the information given in this publication.

© 2021 – Schneider Electric. All rights reserved.
Device user guide_00

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>