WAYTO KP-SUPER7 5-in-1 Super charger User Manual
- June 5, 2024
- WAYTO
Table of Contents
**WAYTO**
User Manual
5 IN 1 SUPER CHARGER
Specification
Capacity:20000mAh 3.85V 77Wh ±5%
Input: 100-240V~50/60Hz 0.5A Type-C Cable PD 5V 3A/9V 2A/12V 1. 5A
Charger mode Output:5V 3A(Total)
Power bank Output: Type-C& Lightning Cable PD/PPS 5V 2.4A/9V 2.22A/12V
1.67A(20W)
2xUSB Output: 4.5V 5A/5V 4.5A/9V 2A/12V 1.5A(22.5W)
MagSafe Wireless Output: 15W/10W/7.5W/5W
Total Output: Cable+2xUSB+Wireless:5V 4.5A(22.5W)
Size: 125x72x33mm
Weight: 400g
Using the adapters
- UK/EU/AU adapters: Attach the appropriate adapter to the charging base/US adapter: pull the adapter out from the charging base then plug it into the plug socket and switch on the power.
- insert your USB cable into one of the USB ports and connect to your device.
- The light will turn blue for a moment and then turn green again to confirm that it’s charging.
Optional Plug for Global Travel ( US plug is standard in the package, more EU/AU/UK plug need additional cost if you need them.)
Function Description
a. Switch Press it once to turn on USB output and wireless charging output It
automatically turns off in 30 seconds under the no-load status
b. Charging the LED digital power display blinks while charging It shows 100
after fully charged.
c. Wireless Charging Make sure your phone is equipped with QI wireless
charging receiver, otherwise, additional wireless charging receiver is needed
to install with your phone.
Working Mode
Dis-Charging:
*Qi wireless charging is 7.5W/10W/15W fast charge while using QI only, it becomes 5W when more USB output in use simultaneously
- Power Delivery (PD) is 20W max while using Type-C&Lightning Cable output only, it becomes common 5V 4.5A max when either QI wireless charging or USB-A output in use simultaneously. Three outputs intelligently distribute the current
Charging: - It’s 5V 3A when use AC plug charging mode, charging time is about 5.5 hours
- Support pass-through charging, Type-C&USB-A output is 5V and intelligent current.
AC Charge For Power Bank
Insert the plug into the socket, and the power bank will be charged.
Car Charge For Power Bank
Connect the built-in Type-C cable with car charger, it will charge your supercharger power bank.
Charge through the wireless charging function
Put the Qi-enabled mobile devices on the supercharger, it will charge your
devices after turning on the power switch. It supports MagSafe charging for
the latest phones like iPhone 12 and 13.
Attention! When using the built-in cable charging, you cannot put the
phone on the wireless charging area, otherwise, it turns to slow charging.
Use supercharge to charge other devices
Connect your mobile device with the built-in charging cable, press the power
button and the Super Charger starts charging your device.
Built-in charging cable USB-C PD20W is suitable for charging laptops up to
30W, not recommended for charging higher power laptops.
Attention! When the iPhone is quickly charged to 80%, it will
automatically switch to slow charging mode without current. The power bank
will automatically shut down and you need to press the switch again to keep
charging the iPhone to 100%.
AC Charge devices through the adapter
Connect a charging cable and charge your mobile device directly. Press the
power button and the super charger starts to charge your devices.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>