LOSRECAL B09FRBSX5P Logistics Label Printer User Guide
- June 5, 2024
- LOSRECAL
Table of Contents
- Product Introduction
- Quick Printer Installation
- Label Setup
- Driver Installation
- Windows Driver Installation
- Mac Driver Installation
- “FEED” Button Instruction
- LED Status
- Platform(Online Store) Setup
- FAQ
- Specifications
- Support
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
**LOSRECAL B09FRBSX5P Logistics Label Printer User Guide
**
Product Introduction
What’s in the box?
- Printer
- Power Adapter
- Power Cable
- USB Cable
- Labels
- User Manual
- Card
- USB Flash Drive
Quick Printer Installation
Note: Please use the power adapter provided by LOSRECAL.
Label Setup
- Facing the front of the printer, press the cover open button to open the top cover.
- Install the label paper with the holders on both sides.
- Finish the label paper installation, and then close the cover.
- For new label paper, do the label size calibration again.
Note : Before using the printer to print labels, please calibrate the paper size
Label size calibration:
- Load at least 4 consecutive sheets of label into the printer.
- Press FEED button and hold on.
- Release the button when you hear one “beep” sound.
- Then, the printer will calibrate the label size.
Driver Installation
Support downloading driver files via download link.
Printer driver download link: https://bit.ly/128driver
Warning
The print head (TPH) will be extremely hot after printing. Do not touch it or any parts around it.
Windows Driver Installation
Note: Please connect to the computer first and then turn on the printer
-
Open the driver file you downloaded. The download link: https://bit.ly/128wind
-
Follow the instruction to install the driver.
-
Check the printer Page Setup (4 in×6 in) in Printing preferences.
Note : If the USB interface cannot be recognized during the installation process, please restart the printer.
Mac Driver Installation
Note : Please connect to the computer first and then turn on the printer.
-
Open the driver software you downloaded. The download link: https://bit.ly/128macd
-
Start installation
-
Follow the guideline to install until “The installation was successful” appears.
-
4. Page Setup, choose 4×6” (100×150 mm), then we can open the document and select the printer to print shipping labels.
“FEED” Button Instruction
Printer status
|
Operation of FEED
|
Function
---|---|---
Standby
|
Short press the button(light)
|
Feed in a blank paper
**** Standby
|
Long press the button(light) until beep once
|
Automatically calibrate paper size
Standby
|
Long press the button(light) until beep twice
|
Print out Self-test page
Standby
|
Long press the button(light) until beep three times
|
Reset printer
LED Status
Description | LED indicator |
---|---|
Power on, waiting for printing instructions | Blue light |
**** The printer is downloading data or paused | Blue light flashing |
The printer is clearing data | Purple light |
The cover is open | Red light |
Printing errors, such as: out of paper, paper jam, or memory error, etc. |
**** Red light flashing
Platform(Online Store) Setup
- Shopify, https://bit.ly/128-shopify
- UPS, https://bit.ly/128-ups1
- Etsy, https://bit.ly/128-etsy-1
- Amazon, https://bit.ly/128-amazon
- eBay, https://bit.ly/128-ebay
- PayPal, https://bit.ly/128-paypal-1
- Pirate Ship, https://bit.ly/128pirateship
- Poshmark, https://bit.ly/128poshmark
- Stamps, https://bit.ly/128stamps
- Shipeasy, https://bit.ly/128shippingeasy
- FedEx, https://bit.ly/128-fedex-1
- USPS, https://bit.ly/128-usps1
- Endica, https://bit.ly/128-endica
- XPS, https://bit.ly/128xps-1
- DHL, https://bit.ly/128dhl1
- Canada Post, https://bit.ly/128-canadapost1
- Royal Mail, https://bit.ly/128-royalmail-1
FAQ
- Q1: What should I do when the printer flashes red?
- A1: When the red light on the top of the printer turns on, please power off the printer then on. Then the red light will change to blue, please follow the steps below to calibrate:
1. Load at least 4 consecutive sheets of label into the printer.
2. When the loaded labels stop moving, press the FEED button(blue light) and hold it until you hear one ‘beep’ sound, then release the button.
3. It will spit out two blank labels, and the gap between labels will stop on the printer’s edge.
-
Q2 :When the printing is too faint, how to adjust the density and printing speed?
-
A2: For Windows : Printer Preferences → Page Setup → Setting; For Mac OS: Can be set in drop-down menu under ‘Printer Features’
-
Q3: What can I do if paper is jammed or there are white spots in my print?
-
A3: Turn off the printer, and allow the printer head to cool down. Use the pad with alcohol to wipe the printer head clean.
-
Q4: Why I am printing blank labels?
-
A4: Make sure your labels are ‘Direct Thermal’ labels and the label that you peel off should be facing the ceiling when it comes out of the printer.
-
Q5: How can we print the label that is not in standard 4*6 size , such as the USPS?
-
A5: You can use the “Adobe Reader” to take a screenshot and print the abel in correct size. Adobe Reader download link: https://get.adobe.com/cn/reader/
The tutorial video: https://bit.ly/128-adobe -
Q6: How to print self-test label?
-
The self-test label can be used to determine whether the machine is malfunctioning and whether the printing performance is good. You can print self-test label as follows.
1. Turn on the printer.
2. Press FEED button and hold on.
3. Release the button when you hear two ‘Beep’ sound.
- FAQ download link : https://bit.ly/128faq
Specifications
Method | Direct Thermal |
---|---|
Resolution | 203 DPI |
Max Printing Speed | 152mm/s |
Paper Width | 108mm |
Paper Thickness | 0.06-0.25mm |
Power Adapter | 24V/2.5A |
Printing Life | TPH 30 Km |
Connection | USB |
Support
Need Tech Support, contact us by:
+86 18218184794
Monday to Friday, 24 hours
References
- (1)Amazon.mp4 - pCloud
- (4)ebay1.mp4 - pCloud
- (5)endica.mp4 - pCloud
- (11)Royal mail.mp4 - pCloud
- (16)USPS.mp4 - pCloud
- (17)XPS.mp4 - pCloud
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>