RIDEVISION RV1 Collision Avoidance System User Manual
- June 5, 2024
- RIDEVISION
Table of Contents
RIDEVISION RV1 Collision Avoidance System
Introduction
Congratulations on buying the world’s most advanced Collision Avoidance System
for two-wheeled vehicles. We built this system specifically for riders like
you, who are dedicated to staying safe while enjoying every ride.
We hope you enjoy this lifechanging and fun product, and we encourage you to
write to us at support@ride.vision with any questions,
feedback, suggestions, or comments you may have.
We strongly encourage you to have the Ride Vision 1 (RV1) system installed on
your vehicle by a certified installer. Certified installers near you can be
found at
www.ride.vision/installers
Once the system is installed, simply open the Ride Vision mobile app to finish
the setup process. The Ride Vision app is available for iOS and Android
devices, more information on the app and its functions can be found at
www.ride.vision/app
Disclaimers
Warning:
RV1 is a rider aid and should be used for informational purposes only. This
product does not replace a safe and conscientious rider or override any rider
inputs. RV1 cannot
compensate for a rider who, without limitation, is distracted, tired or under
the influence of drugs or alcohol. It is the rider’s responsibility to use
safe driving judgment, to take
measures to avoid an accident and to comply at all times with all laws and
regulations.
Warnings:
The ability for RV1 to detect a threat and issue a warning may be limited in
some circumstances, such as, without limitation, bad weather, low visibility
or certain road conditions (e.g., limited view, road obstacles) or if you do
not comply with the maintenance steps described in this manual.
Whether or not RV1 is operating, it is the rider’s responsibility to maintain
vehicle control as described above. Failure to do so may result in serious
personal injury, severe property damage or death.
Ride Vision hereby disclaims any liability for injuries, damages, or death
arising from the use of RV1.
While RV1 represents a state-of-the-art innovation in machine vision software
and other technologies, Ride Vision cannot and does not guarantee 100%
accuracy in the detection of vehicles or driving lanes, and therefore does not
guarantee the provision of any related audio or visual warnings. In addition,
road, weather and other conditions can adversely affect RV1 systems’
recognition and response capabilities.
Limited Warranty:
Ride Vision warrants that the product when used in accordance with its
specifications and instructions will be free from material defects under
normal use for such period as prescribed in the user warranty received with
the purchase of the RV1. Warranty period as well as other applicable warranty
conditions shall be as prescribed in the warranty card received from your
local retailer. In the event of non-conformity during the warranty period,
please contact your nearest certified retailer.
Maintenance and daily use
To ensure optimal operation of the system please follow the scheduled tasks below:
-
Once a week: Clean both camera lenses with a dry cloth
-
Every 3 months: Replace the camera lens glass cover.
-
Once a month: Clean the Main Unit (ECU) by gently washing with water to remove dirt and debris.
-
If a camera position is changed, recalibrate it using the Ride Vision mobile app and the supplied calibration ruler.
-
On every ride, make sure the initial launch sequence is initiated:
Both Alert Indicators’ orange LEDs light up 3 times simultaneously after slow speed is reached. -
In the case of unit malfunction or load failure, all LED lights will dim 5 times.
-
Avoid direct washing of the units.
-
Make sure to synchronize the unit with the mobile app at least once every 2 weeks to ensure unit stays activated (security measure).
-
If the vehicle battery is replaced or drained out, sync the unit with the mobile app.
-
Only touch the ECU when the vehicle is off, and cold.
-
If the vehicle has fallen over or suffered a direct hit to cameras, camera recalibration is required immediately.
-
Make sure camera lenses are clean before each ride.
-
Auto video recording can be enabled from the mobile app.
-
Only use V30 Micro SD cards or higher.
RV1 is an assistive technology, it does not control or take over your vehicle in any way when installed.
Installation
Replacement parts can be purchased from your local retailer.
Installation and instructions:
Only install with a certified installer. Visit
www.ride.vision/installers to find a
certified installer near you. Make sure to secure both cameras and the main
unit with the provided
screws. Do not connect more than 1 extension cable. Once installed, do not
change the camera positions. If a camera position is changed, recalibrate it
using the Ride Vision mobile app and the supplied calibration ruler.
Product Safety Alert:
Only touch the ECU when the vehicle is off, and cold. For more detailed
information, specifications and the user manual please go to
www.ride.vision on the Ride Vision website as well
as the FAQ page located at www.ride.vision/faq
For support please contact support@ride.vision
Terms and conditions and privacy policy can be found on our website
www.ride.vision
Warning:
If you detect any malfunction, please contact us at:
support@ride.vision immediately.
Included Hardware:
- Main Unit (ECU)
- 2 wide-angle HD cameras + cable
- Right & left Alert Indicators + cable
- 2 Alert Indicator anchors
- GPS antenna
- Speed sensor + cable
- Speed Sensor bracket x2 + sensor trigger
- Calibration ruler
- Ball mount x2
Small Extras:
Adhesive tape + installation screws
Tech Specs
SIZE
Front, rear camera (L, W, H)| 38mm, 38mm, 51mm
Main Unit/ECU (L, W, H)| 82mm, 67mm, 39mm
Front, rear cable length| 2.8m, 1m
Electrical Characteristics
Input| 10-14Vdc, 2A
Operating temperature| -10°C to +60C°
Communication Characteristics
BT| 5.0
WIFI| IEEE 802.11ac/a/b/g/n
Display Characteristics
10 LEDs Right and 10 LEDs Left| Red color
5 LEDs Right and 5 LEDs Left| Yellow color
Functionality
Ride Vision (RV1) is an assistive technology, this means it does not control
or take over vehicle function in any way.
Ride Vision alerts (basic version):
| Alert Name | Alert Description | Alert Function |
|---|---|---|
| Forward Collision Alert | Alerts when there is a possibility for a collision | |
| with another vehicle | Blinking red LED lights on |
both mirrors
Distance Keeping Alert
| Alerts when you are consistently and dangerously close to the vehicle in front of you| ****
Constant red LED lights on both mirrors
Blind Spot Alert| Alerts when vehicles are in your blind spots| Constant
yellow LED lights on in relevant mirror
Dangerous
Overtake Alert
| Alerts when speeding vehicles are in your blind spots| Constant yellow LED lights on in relevant mirror
An updated list of features and alerts is always available at www.ride.vision More features and alerts are updated regularly to subscribed users.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>